TIA-4963-2013 Electrical Characteristic of Generators and Receivers with Reversed-Wire Immunity for Use in Balanced Digital Multipoint Systems.pdf

1、 TIA-4963 April 2013Electrical Characteristic of Generators and Receivers with Reversed-Wire Immunity for Use in Balanced Digital Multipoint Systems ANSI/TIA-4963-2013 APPROVED: MARCH 26, 2013 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through elimina

2、ting misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not

3、 in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. S

4、tandards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Stan

5、dard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its u

6、se. (From Project No. ANSI/TIA-PN-4963, formulated under the cognizance of the TIA TR-30 Multi-Media Access, Protocols and Interfaces, TR-30.2 Subcommittee on DTE-DCE Interfaces.) Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 1320 N. Courthouse Road Arlingt

7、on, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call IHS, USA and Canada (1-877-413-5187) International (303-397-2896) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserve

8、d Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact

9、 the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright or Telecommunications Industry Association Technology (b) there is no assurance that the Document

10、will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights

11、(“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested

12、, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the partie

13、s involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Doc

14、ument contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandato

15、ry, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of

16、 voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Pate

17、nt(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPR

18、ESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DI

19、SCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR

20、 PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAM

21、AGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT

22、 OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. ANSI/TIA-4963 i Electrical Characteristic of Generators and Receivers with Reversed-wire Immunity for Use in Balanced Digital Multipoint Systems (From TIA Standards Proposal ANSI/TIA-PN-3-4

23、963 formulated under the cognizance of TIA Subcommittee TR-30.2 on Data Transmission Interfaces) Contents Page 1 SCOPE 1 2 DEFINITIONS, SYMBOLS AND ABBREVIATIONS . 1 2.1 Common-mode voltage (Vcm), 1 2.2 Data signaling rate 1 2.3 Differential . 1 2.4 Generator (Driver), 1 2.5 Ground potential differe

24、nce (Vgpd), . 1 2.6 Longitudinally coupled noise voltage 1 2.7 Multipoint . 1 2.8 Passive-state . 2 2.9 Receiver . 2 2.10 Star (*) 2 2.11 Transceiver 2 2.12 Measured parameter . 2 2.13 Forced voltage 2 3 APPLICABILITY 2 4 ELECTRICAL CHARACTERISTICS . 3 4.1 Unit load characteristics 5 4.1.1 DC Unit l

25、oad specification . 5 4.1.2 AC Load characteristics 6 4.2 Generator characteristics 7 4.2.1 Open circuit output voltages 7 4.2.2 Differential and offset output voltages . 7 4.2.3 Differential output voltages with common-mode loading (Figure 7) 8 4.2.4 Off-state output current . 9 4.2.5 Short-circuit

26、 output characteristics 9 4.2.6 Transient over voltage tolerance . 10 4.2.7 Output signal waveform 10 4.3 Receiver characteristics 11 ANSI/TIA-4963 ii 4.3.1 Input voltage ranges . 11 4.3.2 Input thresholds 12 4.3.3 Input balance measurements 13 4.3.4 Receiver unit load test 13 4.3.5 Transient over v

27、oltage tolerance . 14 4.4 Transceiver characteristics . 14 4.5 System requirements . 14 4.5.1 Balanced interconnecting media characteristics . 14 4.5.2 Cable termination 14 4.5.3 Total load limit . 14 4.5.4 Fail-safe operation 14 Annex A (Informative) . 16 GUIDELINES FOR APPLICATION 16 A.1 Multipoin

28、t system configuration . 16 A.2 Data signaling rate vs. cable length . 16 A.3 Stub lengths 16 A.4 Optional grounding arrangements . 16 A.4.1 Signal common (Ground) 16 A.4.2 Configuration “A“ . 16 A.4.3 Configuration “B“ . 16 A.4.4 Shield ground 17 A.5 Termination . 17 A.6 References 17 ANSI/TIA-4963

29、 iii FOREWORD (This foreword is not part of this Standard.) This Standard was formulated under the cognizance of TIA Subcommittee TR-30.2 on Data Transmission Interfaces. Many applications which use TIA-422-B or TIA-485-A are wired on-site by third-party installers. This opens the door to the possib

30、ility of miss-wiring, especially for far-flung networks with many stations (or nodes). Neither TIA-422-B nor TIA-485-A allows correct communications when the bus wires (typically a twisted-pair) are swapped. The existing solutions for this case require active intervention, either by the installer or

31、 maintenance technician, or by an automated controller. TIA-4963 offers a way to replace TIA-422-B or TIA-485-A networks with communication over the same bus lines. This interface is immune to communication errors caused by crossed bus wires. Its signaling levels are similar to TIA-422-B and TIA-485

32、-A, so signaling rates, cable lengths, and noise immunity will be comparable. TIA-4963 is not completely interoperable with TIA-422-B or TIA-485-A. ANSI/TIA-4963 1 1 SCOPE This Standard specifies the electrical characteristics of generators and receivers that may be employed when specified for the i

33、nterchange of binary signals in multipoint interconnection of digital equipment. When implemented within the guidelines of this Standard, multiple generators and receivers may be attached to a common interconnecting cable. The generators and receivers operate with no errors if the balanced interconn

34、ecting cables are connected normally or with the differential signal wires reversed. An interchange system includes one or more generators connected by a balanced interconnecting cable to one or more receivers with or without terminating resistors. The electrical characteristics of the circuit are s

35、pecified in terms of the required voltage, current, and resistance values obtained by measurements at the equipment interconnect points. This Standard does not specify other characteristics, such as signal quality, timing, protocol, pin assignments, power supply voltage, operating temperature range,

36、 etc., that are essential for proper operation of interconnected equipment. Any devices complying with this Standard shall do so within the ranges of those factors appropriate for the device operation, such as power supply voltages, and ambient temperature. It is intended that this Standard be refer

37、enced by other standards and specifications that specify the additional characteristics necessary to assure satisfactory interoperation of equipment. 2 DEFINITIONS, SYMBOLS AND ABBREVIATIONS For the purposes of this Standard, the following definitions, symbols and abbreviations apply: 2.1 Common-mod

38、e voltage (Vcm), one half of the sum of the voltages between each conductor of a balanced interchange circuit and ground. The common-mode voltage is the sum of ground potential difference; generator offset voltage and longitudinally coupled noise voltage. 2.2 Data signaling rate, expressed in the un

39、its bits (bits per second), is defined as 1/T where T is the minimum interval between two significant instants. 2.3 Differential, the signal is the voltage difference between the A and B, not with respect to common (C). 2.4 Generator (Driver), the component of an interchange circuit that is a source

40、 of the transmitted signal. 2.5 Ground potential difference (Vgpd),the difference between the signal ground potential between the active generator and a receiver of an interchange circuit. 2.6 Longitudinally coupled noise voltage, unwanted voltage coupled inductively or capacitively between any two

41、points along the balanced interconnecting cable (see 2.1). 2.7 Multipoint, a bus structure that has two or more generators and one or more receivers. ANSI/TIA-4963 2 2.8 Passive-state, the output state of the generator presents high impedance. The generator either provides binary 0 outputs or the ge

42、nerator is off. 2.9 Receiver, the component of an interchange circuit that provides for the detection of interchange circuit signals at the receiving equipment. 2.10 Star (*) represents the complementary logical state of a binary signal. For example, the symbol Q represents the receiver output state

43、 for one input condition, while Q* represents the output state for the opposite input state. 2.11 Transceiver, a component that includes both a receiver and generator. 2.12 Measured parameter: 2.13 Forced voltage: 3 APPLICABILITY The provisions of this Standard apply only to the electrical character

44、istics of generators and receivers employed in communications between equipments. The information being conveyed is in the form of binary signals that may have a DC component. This Standard is not, therefore, an interface standard, but shall be referenced by those interface standards or specificatio

45、ns employing generators and receivers having these electrical characteristics. The circuits whose characteristics are specified herein will be utilized normally in data, timing, or control interconnections where the data signaling rate is up to 5 Mbit/s. Devices meeting the electrical characteristic

46、s of this Standard need not operate over the entire data signaling rate range specified nor be limited to 5 Mbps. They may be specified to operate at data rates to satisfy specific applications. The upper bound is application dependent and beyond the scope of this Standard. Maximum data signaling ra

47、te is typically limited by the following: ratio of signal transition time to the unit interval, maximum allowable stub length, and the bandwidth of the interconnecting media. The characteristics are defined such that any device in the system can operate with a common-mode voltage as great as 7V. Com

48、pliant generators may be active simultaneously (contention) without damage. While generator contention may exist, there is no provision within this Standard for the detection of contention. Iib Via ANSI/TIA-4963 3 While the balanced generators and receivers described in this Standard are intended fo

49、r use at high data signaling rates, they may (in preference to the unbalanced generators and receivers) generally be required where any of the following conditions prevail: a) A multipoint (multiple generators) system is required. b) The interconnecting cable is too long for effective unbalanced circuit operation. c) The interconnecting cable is exposed to extraneous noise sources that may cause an unwanted voltage up to 7V measured differentially between the signal conductor and circuit common at the load end of the cable with a 50 resistor substituted for the generator. d) Logical