TIA-568-B 2-11-2005 Commercial Building Telecommunications Cabling Standard Part 2 Balanced Twisted-Pair Cabling Components Addendum 11 Specification of 4-Pair UTP and SCTP Cabling.pdf

1、 TIA STANDARD ANSI/TIA-568-B.2-11-2005Approved: December 2, 2005 Commercial Building Telecommunications Cabling Standard Part 2: Balanced Twisted-Pair Cabling Components Addendum 11 Specification of 4-Pair UTP and SCTP CablingTIA-568-B.2-11 (Addendum No.11 to TIA-568-B.2) DECEMBER 2005 TELECOMMUNICA

2、TIONS INDUSTRY ASSOCIATION Representing the telecommunications industry in association with the Electronic Industries Alliance Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NO

3、TICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay

4、 the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards an

5、d Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent own

6、er, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropri

7、ate safety and health practices and to determine the applicability of regulatory limitations before its use.(From Standards Proposal No. 3-4426-AD11-A-1, formulated under the cognizance of the TIATR-42.7 Subcommittee on Telecommunications Copper Cabling Systems). Published by TELECOMMUNICATIONS INDU

8、STRY ASSOCIATION Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARDS AND ENGINEERING PUBLICATIONS or call Global Engineering Documents, USA and Canada (1-800-854-7179) Int

9、ernational (303-397-7956) or search online at http:/www.tiaonline.org/standards/search_n_order.cfm All rights reserved Printed in U.S.A. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from

10、IHS-,-,-NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact TIA Standar

11、ds Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/about/faqDetail.cfm?id=18 OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Comm

12、ittee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending o

13、r issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the

14、 Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opi

15、ne or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. TIA does not enforce or monitor compli

16、ance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES C

17、ONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO RE

18、PRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AN

19、D ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED U

20、PON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA

21、WITHOUT SUCH LIMITATIONS. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-568-B.2-11 i SPECIFICATION FOR INCREASED DIAMETER OF 4-PAIR UTP AND ScTP CABLES TABLE OF CONTENTS 1

22、 INTRODUCTION.1 2 PURPOSE AND SCOPE.1 2.1 Applicability . 1 3 NORMATIVE REFERENCES .1 4 MODIFICATIONS TO TIA-568-B.2 .1 4.1 Cable diameter1 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license fr

23、om IHS-,-,-TIA-568-B.2-11 ii FOREWORD (This foreword is not part of the Standard) TIA standards documents are developed within the Technical Committees of the TIA and the standards coordinating committees of the TIA standards board. Members of the committees serve voluntarily and without commission.

24、 The companies that they represent are not necessarily members of the TIA. The standards developed within the TIA represent a consensus of the broad expertise on the subject. This expertise comes from within the TIA as well as those outside of the TIA that have an expressed interest. The viewpoint e

25、xpressed at the time that this standard was approved was from the contributors experience and the state of the art at that time. Users are encouraged to verify that they have the latest revision of the standard. This standard has been prepared by the TR-42.7 Subcommittee and approved by the TR-42 En

26、gineering Committee. There are no annexes in this Standard. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-568-B.2-11 1 1 INTRODUCTION This Standard specifies an increased

27、maximum cable diameter for 4-pair balanced UTP and ScTP cables. Deleted text is shown as strikethrough and new text is shown as underlined. 2 PURPOSE AND SCOPE This Standard specifies the requirements for the cable diameter of 4-pair balanced UTP and ScTP cables specified in TIA-568-B.2. 2.1 Applica

28、bility This Standard applies to 4-pair balanced UTP and ScTP cables specified in TIA-568-B.2 and TIA-568-B.2-1. 3 NORMATIVE REFERENCES The following standards contain provisions that, through reference in this text, constitute provisions of this Standard. At the time of publication, the editions ind

29、icated were valid. All standards are subject to revision; parties to agreements based upon this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated. ANSI and TIA maintain registers of currently valid national standards published by t

30、hem. TIA-568-B.2 Commercial Building Telecommunications Cabling Standard, Part 2: Balanced twisted pair cabling components, 2001 TIA-568-B.2-1 Addendum 1: Transmission Performance Specifications for 4-Pair 100 Category 6 Cabling, 2002 4 MODIFICATIONS TO TIA-568-B.2 4.1 Cable diameter The requirement

31、 in clause 4.3.3.4 of TIA -568-B.2 shall be revised as follows: The diameter of the completed cable shall be less than 6.35 mm (0.25 in.) 9.0 mm (0.354 in). NOTE: Larger cable diameter cables may not be compatible with certain designs of modular connecting hardware. For example, the termination caps

32、 in some modular outlets designs may not accommodate larger diameter cables. When 4-pair cables with overall diameters of greater than 6.35 mm (0.25 in.) are used, compatibility with connecting hardware should be considered. Copyright Telecommunications Industry Association Provided by IHS under lic

33、ense with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Telecommunications Indu

34、stry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-