TIA-612-1993 Electrical Characteristics for an Interface at Data Signaling Rates up to 52 Mbit s《在数据信令高达52 Mbit s的接口的电气特性》.pdf

1、 TIA/EIA-612-1993 APPROVED: NOVEMBER 2, 1993 REAFFIRMED: SEPTEMBER 10, 1999 REAFFIRMED: SEPTEMBER 14, 2005 REAFFIRMED: JULY 29, 2014 TIA-612 December 1993Electrical Characteristics for an Interface at Data Signaling Rates up to 52 Mbit/s NOTICE TIA Engineering Standards and Publications are designed

2、 to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence

3、 of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA membe

4、rs, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties ad

5、opting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applica

6、bility of regulatory limitations before its use. Any use of trademarks in this document are for information purposes and do not constitute an endorsement by TIA or this committee of the products or services of the company. (From Project No. PN-3-4394-RF3, formulated under the cognizance of the TIA T

7、R-30.2 Subcommittee on DTE-DCE Interfaces). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Technology (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in

8、 the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR co

9、nsisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope

10、 or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or

11、 represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged in the formulation, developmen

12、t or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Procedures for American National Standards) then (i) TIA disclaims any duty or obligation

13、to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see TIA Procedures for American National Standards Annex C.1.2.3) of Essential Patent(s) and published pending pa

14、tent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents

15、 of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY

16、 OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRAN

17、TIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT O

18、R INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT,

19、 BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATION

20、S. EIA TIA-bL2 93 = 3234600 0552390 4b7 ELECTRICAL CHARACTERISTICS FOR AN INTERFACE AT DATA SIGNALING RATES UP TO 52 Mbis (From Standards Proposai Nos . 2795. 2795-1 and 2795.2. formulated under the cognizance of TIA TR30.2 Subcommittee on Data Transmission Interfaces) Contents Page 1 2 3 3.1 3.1.1

21、3.1.2 3.1.3 3.1.4 3.2 3.2.1 O 3.2.2 3.2.3 3.2.4 3.3 4 5 SCOPE 1 APPLICABILITY . 2 ELECTRICAL CHARACTERISTICS . 3 Generator Characteristics 3 Open Circuit Measurement . 4 Output Signal Waveform 6 Test Termination Measurements . 5 Short Circuit Measurement 5 Load Characteristics . 7 Input Current-Volt

22、age Measurements . 7 Input Sensitivity Measurements 7 Failsafe Operation . 9 Cable Termination . 9 Interconnecting Cable Electrical Characteristics . 10 ENVIRONMENTAL CONSTRAINTS . 10 CIRCUIT PROTECTION 11 Annex A (informative) . 12 A . 1 A.l.l Length 12 A.1.2 Cable Physical Characteristics 12 A.1.3

23、 Cable Termination . 12 A.2 A.2.1 A.2.2 Interconnecting Cable 12 ECL Generators and Receivers 13 ECL - Emitter Coupled Logic Technology 13 Failsafe Biasing of Receivers . 13 Annex B (informative) . 14 References 14 a i EIA TIA-612 93 m 3234600 0552191 3T3 m This Page Intentionally Left Blank EIA TIA

24、-h32 93 m 3234h00 0552392 23T = FOREWORD (This foreword is not part of this Standard) This Standard was formulated under the cognizance of TIA Subcommittee TR-30.2 on Data Transmission Interfaces. It is intended to be used with ANSIKIAEIA-613-1993, High Speed Serial Interface for Data Terminal Equip

25、ment and Data Circuit- Terminating Equipment. This Standard specifies generators and receivers capable of operating at data signaling rates up to 52 Mbits. This Standard was developed in response to a demand from the data communications community for a high speed general purpose DTE-DCE interface. A

26、nnex A of this Standard is informative and provides guidelines for application. Annex B of this Standard is also informative and provides references to this Standard. Neither Annex is considered part of this Standard. I iii EIA TIA-bL2 93 323YbOO 0552393 376 This Page Intentionally Left Blank iv EIA

27、 TIA-b32 93 m 3234600 0552394 O02 m ANSI/TIA/EIA-612-1993 1 SCOPE This Standard sDecifies the electrical characteristics of the balanced diaital interface circuit, normally implemented in integrated circuit technology, ?hat may be employed when specified for the interchange of serial binary signals

28、between Data Terminal Equipment (DTE) and Data Circuit-Terminating Equipment (DCE) or in any point-to-point interconnection of serial binary signals between data equipments. The interface circuit includes a generator connected by a balanced interconnecting cable to a load consisting of a receiver an

29、d a termination. The electrical characteristics of the circuit are specified in terms of required voltage, and current values obtained from direct measurements of the generator and receiver components at the interface points. The logic function of the generator and the receiver is not defined by thi

30、s Standard, as it is ap pl cat io n -dependent. Minimum electrical requirements for the interconnecting cable are f u rnis h ed. It is intended that this Standard will be referenced by ANSI/TIA/EIA-613-1993, High Speed Serial Interface for Data Terminal Equipment and Data Circuit- Terminating Equipm

31、ent, that specifies the other necessary components of an interface (e.g., connector, pin assignments, function) for applications where the electrical characteristics of a high speed balanced digital circuit are required. 1 EIA TIA-bL2 93 3239600 0552195 T49 D D T E ANSI/TIA/EIA-612-1993 D C E 2 APPL

32、ICABILITY Id L The provisions of this Standard may be applied to the circuits employed at the interface between equipments where information being conveyed is in the form of binary signals. Typical points of applicability for this Standard are depicted in figure 1. Legend: DTE = Data Terminal Equipm

33、ent DCE = Data Circuit-Terminating Equipmc E = Interface Generator = Interface Receiver = Balanced Interface Circuit - Figure 1 - Applications of balanced digital interface circuit The balanced digital interface circuit will normally be utilized on data and timing, or control circuits where the data

34、 signaling rate is up to a maximum limit of 52 Mbis. In this Standard, the term: data signaling rate, expressed in the units bit/s (bits per second), is the significant parameter. It may be different from the equipments data transfer rate, which employs the same units. Data signaling rate is defined

35、 as 1/T where T is the minimum interval between two significant instants. In a binary system for which this Standard is designed, the data signaling rate in bitk and the modulation rate in bauds are numerically equal when the unit interval used in each determination is the minimum interval. star (*)

36、 represents the opposite input condition for a parameter. For example, the symbol Q represents the receiver output state for one input condition, while Q represents the output state for the opposite input state. 2 EIA TIA-bL2 93 3234600 055219b 985 = ANSITTINEI-612-1993 3 ELECTRICAL CHARACTERISTICS

37、The balanced digital interface circuit is shown in figure 2. The circuit consists of three parts: the generator (G), the balanced interconnecting cable, and the load. The load is composed of a receiver (R) and a cable termination/faiIsafe network. The electrical Characteristics of the generator and

38、receiver are specified in terms of direct electrical measurements while the interconnecting cable is described in terms of its electrical characteristics. + GENERATOR )+BALANCED INTERFACL LOAD b Cable CABLE Vee B 755- B 1 Rt = 110 R Rrp = Q 1.5 k(l I I Legend: G = Generator Rgp = Generator Pull Down

39、 Resistor R = Receiver Rt = Termination Resistor Rrp = Receiver Bias Resistor (Optional, Receiver Dependent) Vcpd = Common Potential Difference Vee = Negative Voltage Power Supply NOTE: All resistors f 2% A,B = Generator Interface Points A,B = Receiver Interface Points C = Generator Circuit Common C

40、 = Receiver Circuit Common Figure 2 - Balanced digital interface circuit 3.1 Generator Characteristics The generator electrical characteristics are specified in accordance with the measurements illustrated in figures 3 to 6 and described in 3.1.1 through 3.1.4. The generator circuit meeting these re

41、quirements results in a low impedance 3 EIA TIA-bL2 93 m 3234b00 0552377 BLL ANSITTINEIA-612-1993 balanced source that will produce a differential voltage applied to the interconnecting cable in the range of 590 mV to 1500 mV. The signaling sense of the voltages appearing across the interconnecting

42、cable are defined as follows: a. The A terminal of the generator shall be negative with respect to the B terminal for a binary O (SPACE or OFF) state. b. The A terminal of the generator shall be positive with respect to the B terminal for a binary 1 (MARK or ON) state. NOTE -, The sense of data bina

43、ry O (SPACE) and data binary 1 (MARK) are inverted from that specified in ElMIA-422-A. The logic function of the generator and the receiver is beyond the scope of this Standard, and therefore is not defined. 3.1.1 Open Circuit Measurement (Figure 3) For either binary state, the magnitude of the diff

44、erential voltage (VOC or VOC) measured between the two generator output terminals shall not exceed 1.5 V. Vee T- OPEN CIRCUIT MEASUREMENT I VOC I 51.5 v, I VOC I 5 1.5 V 0 = Measured Parameter I Vee Figure 3 - Open circuit measurement 4 ANSITTINEIA-612-1993 3.1.2 Test Termination Measurements (Figur

45、e 4) With a test load of the resistors shown in figure 4, the magnitude of the differential output voltage (Vt), shall be 590 mV or greater. For the opposite binary state, the polarity of Vt shall be reversed (Vt*). The magnitude of the difference between Vt and Vt shall be less than 100 mV. The mag

46、nitude of the generator offset voltage (Vos), measured between the center point of the test load and the generator circuit common shall be -1.6 V or more positive for either binary state. The magnitude of the difference of Vos for one binary state and Vos for the opposite binary state shall be 1 O0

47、mV or less. Vee TEST TERMINATION MEASUREMENTS I Vt I 2 590 mV, I Vt I 2 590 mV I I Vt I - I Vt I I I 100 mV I Vos - Vos I I 100 mV = Measured Parameter O V 2 VOS 2 -1.6 V, O V 2 VOS 2 -1.6 I Vee Figure 4 - Test termination measurements 3.1.3 Short-Circuit Measurement (Figure 5) With the generator ou

48、tput terminals short-circuited to each other, the magnitude of the current (los) following between each output terminal shall not exceed 50 mA in magnitude, for either binary state. SHORT CIRCUIT MEASUREMENT I los I s 50 mA, I los I I50 mA = Measured Parameter Vee Figure 5 - Short-circuit measuremen

49、t 5 EIA TIA-bL2 73 3234600 0552377 b74 ANSI/TIA/EIA-612-1993 3.1.4 Output Signal Waveform (Figure 6) During transitions of the generator output between alternating binary states (one-zero-one-zero, etc.), the differential voltage measured across the 1 1 O Q test load connected between the generator output terminals shall be such that the voltage monotonically changes between 0.2 and 0.8 of Vss within 0.5 ns to 2.3 ns. Thereafter, the signal voltage shall not vary more than 10% of Vss from the steady state value, until the next binary transition occurs, and at no tim