1、g3g3TIA-631-B (Revision of TIA-631-A) February 2011Telecommunications Telephone Terminal Equipment Radio Frequency Immunity Requirements ANSI/TIA-631-B 2011 APPROVED: FEBRUARY 15, 2011 NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating mis
2、understandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any
3、respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards
4、 and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard doe
5、s not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (Fro
6、m Project No. 3-3210-RV2-1, formulated under the cognizance of the TIA TR-41 User Premises Telecommunications Requirements, TR-41.7 Subcommittee on Environmental (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (
7、c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA
8、 makes no search or investigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims an
9、y obligation to investigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are rea
10、sonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organizatio
11、n (“other SSO”) engaged in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then
12、 (i) TIA disclaims any duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and publis
13、hed pending patent applications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance wit
14、h the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNIN
15、G THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTAT
16、IONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAM
17、AGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREAC
18、H OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT S
19、UCH LIMITATIONS. TIA-631-B TABLE OF CONTENTS 1. SCOPE_ 1 2. CATEGORIES OF CRITERIA _ 1 3. NORMATIVE REFERENCES _ 1 4. ABBREVIATIONS, ACRONYMS, AND DEFINITIONS _ 2 4.1. ABBREVIATIONS AND ACRONYMS _ 2 4.2. DEFINITIONS_ 3 5. TECHNICAL REQUIREMENTS_ 4 5.1. GENERAL INFORMATION _ 4 5.1.1. Ambient Conditio
20、ns _ 4 5.1.2. TTE Configuration and Operating Conditions _ 4 5.1.3. Test Configuration Conditions _ 5 5.1.4. CO Simulator Analog DC Feed Test Circuit _ 6 5.1.5. Standardized Telephone Load Test Circuit_ 7 5.2. IMMUNITY TO RADIATED ELECTRIC FIELD (E-FIELD) INTERFERENCE _ 7 5.2.1. Receive (Near End In
21、terference) Requirements _ 7 5.2.2. Transmit (Far End Interference) Requirements _ 8 5.2.3. Functionality Requirements _ 9 5.2.4. Method of Measurement_ 9 5.3. IMMUNITY TO CONDUCTED INTERFERENCE ON SIGNAL LEADS _ 14 5.3.1. Receive (Near End Interference) Requirements _ 14 5.3.2. Transmit (Far End In
22、terference) Requirements _ 15 5.3.3. Functionality Requirements _ 15 5.3.4. Method of Measurement_ 15 5.4. IMMUNITY TO CONDUCTED INTERFERENCE ON POWER LEADS_ 19 5.4.1. Receive (Near End Interference) Requirements _ 19 5.4.2. Transmit (Far End Interference) Requirements _ 20 5.4.3. Functionality Requ
23、irements _ 21 5.4.4. Method of Measurement_ 21 6. ALTERNATIVE METHOD CONDUCTED RF SIGNALS ON POWER AND SIGNAL LEADS_ 24 ANNEX A - TEST EQUIPMENT (INFORMATIVE)_ 25 ANNEX B OVERVIEW (INFORMATIVE) _ 28 ANNEX C HISTORICAL BACKGROUND (INFORMATIVE) _ 29 ANNEX D RFI CONSIDERATIONS (INFORMATIVE) _ 30 ANNEX
24、E EXTENSION TO PRODUCTS OTHER THAN HANDSET TELEPHONES (INFORMATIVE) _ 31 ANNEX F INFORMATIVE REFERENCES _ 33 i TIA-631-B Table of Figures Figure 1 CO simulator .6 Figure 2 Standardized telephone test set simulator7 Figure 2 Radiated mode near end requirement 8 Figure 3 Radiated mode far end requirem
25、ent.9 Figure 4 General TEM cell test setups for radiated E-field immunity.11 Figure 5 Cordless TTE handset orientation for radiated E-field immunity .12 Figure 6 Cordless TTE angled handset orientation for radiated E-field immunity12 Figure 7 Corded handset orientation for radiated E-field immunity1
26、3 Figure 8 Adjunct TTE orientation for radiated E-field immunity13 Figure 9 Conducted mode on signal leads near end requirement 14 Figure 10 Conducted mode on signal leads far end requirement.15 Figure 11 Test configuration for conducted immunity on signal leads .17 Figure 12 Cordless TTE handset or
27、ientation for conducted immunity18 Figure 13 Corded TTE orientation for conducted immunity .18 Figure 14 Adjunct TTE orientation for conducted immunity 19 Figure 15 Conducted mode on power leads near end requirement20 Figure 16 Conducted mode on power leads far end requirement 21 Figure 17 Detailed
28、test configuration for metallic conducted immunity on power leads 23 Figure 18 TEM cell test configuration for conducted immunity .24 Figure 19 Types of TEM cell25 Table of Tables Table 1 Climatic conditions during testing4 Table 2 RF signal characteristics for radiated mode E-field7 Table 3 RF sign
29、al characteristics for conducted mode on signal leads14 Table 4 RF signal characteristics for conducted mode on power leads .19 ii TIA-631-B FOREWORD (This foreword is not a part of this Standard.) This Standard was originally developed in the early 1990s in response to numerous consumer complaints
30、to the Federal Communications Commission (FCC) about landline telephones being susceptible to Radio Frequency Interference (RFI), with the most frequent complaints concerning telephones picking up AM radio broadcasts. Additional information concerning its development may be found in the annexes. The
31、 Standard was revised in 2002 with a major restructuring in format, additional clarity about testing procedures, and some minor changes to the requirements. The main purpose of the current revision is to update references and to clarify that the document as written only applies directly to telephone
32、s with handsets. However, a new informative annex has been added to suggest how the test procedures and performance requirements may be extended to additional products such as speakerphones, answering systems, and telephones with headsets. There are 6 annexes, all of which are informative and are no
33、t considered part of this Standard. This Standard was produced by Subcommittee TR-41.7, Environmental and Safety Considerations, of Engineering Committee TR-41, User Premises Telecommunication Requirements. It was developed in accordance with TIA procedural guidelines and represents the consensus po
34、sition of the Subcommittee, which served as its formulating group. It also received the concurrence of TR-41. The leadership of the TR-41.7 Environmental and Safety Considerations Subcommittee (Chair Randy Ivans, Underwriters Laboratories) acknowledges the written contributions provided by the follo
35、wing individuals in the development of this Standard. Organization Representative TIA-631-B VTech Communications Stephen R Whitesell 9 Editor AST Technology Labs, Inc. Don McKinnon 9 Suggestions for improvement of this standard are welcome. They may be sent to: Telecommunications Industry Associatio
36、n Engineering Department Suite 300 2500 Wilson Boulevard Arlington, VA 22201 iii TIA-631-B 1. SCOPE This standard specifies Radio Frequency (RF) immunity performance criteria for two-wire Telephone Terminal Equipment (TTE) having an acoustic output and two-wire TTE adjunct devices with connection po
37、rt for Telephone Terminal Equipment (TTE) having an acoustic output. Acoustic output requirements are only defined for TTE having a handset normally held to the ear of the user, but guidance on extending the requirements to TTE having other types of acoustic outputs, such as speakerphones, answering
38、 systems and telephones with headsets, is provided in an informative annex. Criteria are specified for immunity to radiated RF signals over the frequency range from 150 KHz to 150 MHz and for immunity to longitudinal (common mode) conducted RF signals over the frequency range from 150 KHz to 30 MHz.
39、 Criteria for immunity to metallic (differential) conducted RF signals on signal leads are not covered. In addition to the performance levels themselves, this standard includes recommended test procedures or references to existing standards wherein such procedures will be found. This standard does n
40、ot consider immunity performance criteria to intentional network signals (e.g. xDSL). 2. CATEGORIES OF CRITERIA Three types of requirements are specified in this standard; Mandatory, Recommended and Permissive 1. Mandatory requirements are designated by the terms “shall” and “shall not”. These requi
41、rements are used to indicate conformity in which no deviation is permitted. 2. Recommended requirements are designated by the terms “should” and “should not”. These requirements generally relate to compatibility or performance advantages towards which future designs should strive. 3. Permissive requ
42、irements are designated by the terms “may” and “may not”. These requirements are used to indicate an action that is permitted within the limits of the standard. 3. NORMATIVE REFERENCES The following standards contain provisions, which, through reference in this text, constitute provisions of this St
43、andard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. ANSI and TIA maintain re
44、gisters of currently valid national standards published by them. 1. ANSI/TIA-470.110-C Telecommunications - Telephone Terminal Equipment- Handset Acoustic Performance Requirements for Analog Terminals 1 TIA-631-B 4. ABBREVIATIONS, ACRONYMS, AND DEFINITIONS For the purpose of correct interpretation o
45、f this document, the following key technical terms and abbreviations apply. Terms used in the document but not defined in this section shall be interpreted according to their internationally accepted definition. 4.1. ABBREVIATIONS AND ACRONYMS For the purposes of this Standard, the following abbreviations and
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1