1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1004-1 Rotating Electrical Machines General RequirementsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT
2、AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Rotating Electrical Machines General Requirements, UL 1004-1 Second Edition, Dated September 19, 2012 Summary of Topics This revision of ANSI/UL 1004-1 includes the following change in requireme
3、nts: Revised denitions for air-over motors and continuous duty motors Revised temperature test method to include SF Temperature test stabilization requirement Revisions to direct-support material properties for universal motors Alternative method to evaluate materials used as splice insulation The e
4、ffective date for UL LLC will be announced through Industry File Review Announcement Letter. The new and revised requirements are substantially in accordance with Proposal(s) on this subject dated January 30, 2015. Text that has been changed in any manner or impacted by ULs electronic publishing sys
5、tem is marked with a vertical line in the margin. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this S
6、tandard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, l
7、ost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standa
8、rd, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation
9、 introduced while purchaser is storing an electronic Standard on the purchasers computer system. JUNE 18, 2015 UL 1004-1 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JUNE 18, 2015 UL 1004-1 tr2 No Text on This PageUL COPYRIGHTED MATERI
10、AL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SEPTEMBER 19, 2012 (Title Page Reprinted: June 18, 2015) 1 UL 1004-1 Standard for Rotating Electrical Machines General Requirements First Edition September, 2008 Second Edition September 19, 2012 This ANSI/UL Stand
11、ard for Safety consists of the Second Edition including revisions through June 18, 2015. The most recent designation of ANSI/UL 1004-1 as an American National Standard (ANSI) occurred on June 16, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages and Title Page. Co
12、mments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor ele
13、ctronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2015 UNDERWRITERS LABORATORIES INC. ANSI/UL 1004-1-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZ
14、ED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SEPTEMBER 19, 2012 ROTATING ELECTRICAL MACHINES GENERAL REQUIREMENTS - UL 1004-1 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTI
15、ON 1 Scope .5 2 Components 6 3 Units of Measurement .6 4 Undated References 6 5 Glossary .7 CONSTRUCTION 6 Current and Horsepower Relation 11 7 Motors Provided With Controls 14 8 Mechanical Assembly 15 9 Frame and Enclosure 16 9.1 General 16 9.2 Cast metal enclosures .17 9.3 Sheet metal enclosures 1
16、7 9.4 Polymeric enclosures 19 10 Grounding .20 11 Grounding Identication .21 12 Ventilation Openings 22 12.1 General .22 12.2 Barriers used with ventilation openings 23 13 Accessibility of Uninsulated Live Parts, Film-Coated Wire, and Moving Parts .25 14 Protection Against Corrosion .31 15 Cord-Conn
17、ected Motors .33 16 Input and Output Connections 35 17 Factory Wiring Terminals and Leads 41 18 Spacings 42 19 Current-Carrying Parts 45 20 Internal Wiring 45 21 Bonding for Grounding 48 21.1 Bonding conductor .48 21.2 Bonding and grounding connections 49 21.3 Resilient elastomeric mountings 49 22 E
18、lectrical Insulation .50 23 Insulation Systems 50B 24 Windings 55 25 Brush Holders 55 26 Capacitors .56 27 Switches .56 28 Non-metallic Functional Parts 57 29 Traction Motors .59 PERFORMANCE 30 General 59 31 Ratings Tests 60 31.1 Generator output test .60 31.2 Motor rating test 61 SEPTEMBER 19, 2012
19、 ROTATING ELECTRICAL MACHINES GENERAL REQUIREMENTS - UL 1004-1 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 31.3 Air-over motor rating test 61 32 Temperature Test .61 33 Mechanical Tests .65 33.1 General .65 33.2 Pressure test 66 33.3 Im
20、pact test 66 33.4 Mold stress relief .66 33.5 Conduit hubs 67 33.6 Rain test 67 33.7 Lifting lugs 71 33.8 Vibration test for traction motors .71 34 Strain Relief Test .71 34.1 Power-supply cord 71 34.2 Interconnecting leads .71 34.3 Clamps .72 35 Push-Back Relief Test .72 36 Resilient Elastomer Moun
21、ting Tests .72 36.1 General .72 36.2 Overcurrent test 73 36.3 Humidity conditioning test .75 36.4 Oven conditioning test 75 36.5 Ozone conditioning .75 36.6 Oil conditioning test .76 37 Dielectric Voltage-Withstand Test .76 37A Commutator Conditioning Test .76A 38 Limited Short Circuit Test 77 39 Gr
22、ounding Test .78 40 Oil Compatibility Test 78 41 Electrolytic Capacitor Overvoltage Test 79 42 Locked Rotor Test for Non-metallic Functional Parts 79 42.1 General .79 42.2 Motors not provided with thermal motor protection 80 42.3 Motors provided with thermal motor protection in the form of a thermal
23、 cutoff 81 42.4 Impedance protected motors 81 42.5 Motors provided with thermal motor protection in the form of an automatically reset thermal motor protector .81 42.6 Motors provided with thermal motor protection in the form of an manually reset thermal motor protector, single-operation device, or
24、a self-holding thermal motor protector . . .82 MANUFACTURING AND PRODUCTION TESTS 43 Production-Line Dielectric Voltage-Withstand Test 82 MARKINGS 44 General 84 45 Legibility and Permanence .86 46 Environmental Related Markings .86 INSTRUCTIONS 47 General 87 JUNE 18, 2015 ROTATING ELECTRICAL MACHINE
25、S GENERAL REQUIREMENTS - UL 1004-1 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 This Standard applies to rotating electrical machines and linear motors, both AC and DC, rated 7,200 volts or less. 1.2 This Standar
26、d is used to evaluate both motors intended to be eld installed as well as those intended to be factory installed. Motors intended to be factory installed need not comply with the requirements in Section 12, Ventilation Openings; Section 13, Accessibility of Uninsulated Live Parts, Film-Coated Wire,
27、and Moving Parts; 16.9 16.16, 16.28, 18.1 18.5, 33.1 33.3, 33.5 33.7, and 34.1. 1.3 For the purposes of this Standard, the term “machine” is representative of and equivalent to the terms rotating electrical machine and rotating machine, and is understood to mean all manner of electric motors and gen
28、erators covered by the scope of this Standard. The term “machine” is understood to apply to both AC and DC machines. 1.4 These requirements do not cover machines intended for use in hazardous locations as dened in the National Electrical Code, NFPA 70. The National Electrical Code and NEC are regist
29、ered trademarks of the National Fire Protection Association, Inc., Quincy, MA 02169 1.5 These requirements do not cover sealed (hermetic type) motor-compressor parts, which are evaluated under the Standard for Hermetic Refrigerant Motor-Compressors, UL 984. 1.6 If the risk of re does not exist at a
30、machine, part, or circuit, then the requirements of this Standard and associated parts of this Standard, intended to address the risk of re shall not apply to that machine, part, or circuit. 1.7 If the risk of electric shock does not exist at a machine, part, or circuit, then the requirements of thi
31、s Standard and associated parts of this Standard, intended to address the risk of electric shock shall not apply to that machine, part, or circuit. 1.8 The requirements of this Standard and associated parts of this Standard, intended to address the risk of re do not apply to a motor provided with a
32、metal enclosure in which there are no openings in the enclosure through which molten metal, burning insulation, aming particles, or other ignited material could fall onto ammable material, or through which a ame could be projected. SEPTEMBER 19, 2012 ROTATING ELECTRICAL MACHINES GENERAL REQUIREMENTS
33、 - UL 1004-1 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 Components 2.1 Except as indicated in 2.2, a component of a product covered by this Standard shall comply with the requirements for that component. In particular: a) Positive Te
34、mperature Coefficient devices (PTCs) used in self-holding thermal motor protectors shall comply with the Standard for Thermistor-Type Devices, UL 1434. b) Solid-state controllers shall comply with the Standard for Automatic Electrical Controls for Household and Similar Use, Part 1: General Requireme
35、nts, UL 60730-1. c) Thermal protectors shall comply with the Standard for Automatic Electrical Controls for Household and Similar Use; Part 2 Particular Requirements for Thermal Motor Protectors, UL 60730-2-2. 2.2 A component is not required to comply with a specic requirement that: a) Involves a fe
36、ature or characteristic not required in the application of the component in the product covered by this standard, or b) Is superseded by a requirement in this standard. 2.3 A component shall be used in accordance with its rating established for the intended conditions of use. 2.4 Specic components a
37、re incomplete in construction features or restricted in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 3 Units of Measurement 3.1 Values sta
38、ted without parentheses are the requirement. Values in parentheses are explanatory or approximate information. 4 Undated References 4.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or s
39、tandard. JUNE 18, 2015 ROTATING ELECTRICAL MACHINES GENERAL REQUIREMENTS - UL 1004-1 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5 Glossary 5.1 For the purpose of this standard, the following denitions apply. 5.2 AIR-OVER MOTOR A motor
40、that relies upon a stream of air to cool the motor and is marked in accordance with 44.8. 5.3 ARAMID PAPER An aromatic polyamide (such as Nomex). 5.4 ARMATURE The part of a machine that has windings and rotates. 5.5 AUXILIARY SWITCH A switch that is actuated by motor rotation and intended to control
41、 an external load. 5.6 BONDED (BONDING) The permanent joining of metallic parts to form an electrically conductive path that provides electrical continuity and the capacity to conduct any current likely to be imposed without a risk of electric shock, re, or injury to persons. 5.7 BONDING CONDUCTOR A
42、 conductor, including a strap or similar part, that is used to provide the required electrical conductivity between metal parts required to be electrically connected. 5.8 BRUSH A conducting part that provides electrical connection to the armature of a machine through a commutator. 5.9 BRUSH HOLDER A
43、 structure that supports the brush and provides a means to maintain contact with the commutator of the armature. 5.10 CAMBRIC A varnish-impregnated white linen fabric using an electrical grade resin. 5.11 COMMUTATOR An assembly of conducting members insulated from one another, against which the brus
44、hes bear, that provides electrical connection to the circuits of the armature. 5.12 CONTINUOUS DUTY MOTOR A motor intended to operate indenitely at rated load. 5.13 DIRECTLY ACCESSIBLE MACHINE A machine that can be physically contacted without opening or removing any part, or is located so that it i
45、s accessible to contact. 5.14 ELECTRICAL GRADE PAPER Paper produced from wood pulp formed by wood chips boiled in an alkaline solution containing sodium sulfate. 5.15 ENCLOSED MACHINE A machine that is totally enclosed in order to prevent the free exchange of air between the inside and outside of th
46、e enclosure for the windings. It may not be sufficiently enclosed to be airtight. 5.16 ENCLOSURE That portion of a unit that: a) Reduces the accessibility of a part that involves a risk of re, electric shock, or injury to persons; or b) Reduces the risk of propagation of ame, sparks, and molten meta
47、l initiated by an electrical disturbance occurring within. JUNE 18, 2015 ROTATING ELECTRICAL MACHINES GENERAL REQUIREMENTS - UL 1004-1 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5.17 END SHIELD A part of the machine used to protect the
48、 windings and to support the bearing, but does not include either part. It is secured to the frame. Also called an end bell, end cap, or bracket. 5.18 FACTORY INSTALLATION The act of wiring and mounting a rotating electric machine in a manufacturing environment under controlled conditions by trained
49、 personnel. 5.19 FIELD INSTALLATION The act of wiring and mounting a rotating electric machine outside of a manufacturing environment where the installation is subject to the requirements of the National Electrical Code, NFPA 70. 5.20 FIELD TERMINAL COMPARTMENT Where the outgoing power is connected to the machine at the eld installation site and the connection is a wire-to-terminal connection. 5.21 FIELD WIRING COMPARTMENT Where the outgoing power
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1