UL 1248-2006 UL Standard for Safety Engine-Generator Assemblies for Use in Recreational Vehicles《旅游车用安全发动机发电机组件的UL标准》.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL 1248Engine-Generator Assembliesfor Use in RecreationalVehiclesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL N

2、OT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUnderwriters Laboratories Inc. (UL)333 Pfingsten RoadNorthbrook, IL 60062-2096UL Standard for Safety for Engine-Generator Assemblies for Use in Recreational Vehicles, UL 1248Third Edition, Dated December 8, 2006Revisions

3、: This Standard contains revisions through and including August 29, 2008Summary of TopicsThis revision to UL 1248 includes a correction to a typographical error in paragraph 23.4.Text that has been changed in any manner is marked with a vertical line in the margin. Changes inrequirements are marked

4、with a vertical line in the margin and are followed by an effective date noteindicating the date of publication or the date on which the changed requirement becomes effective.The revisions dated August 29, 2008 include a reprinted title page (page1) for this Standard.The UL Foreword is no longer loc

5、ated within the UL Standard. For information concerning the use andapplication of the requirements contained in this Standard, the current version of the UL Foreword islocated on ULStandardsInfoNet at: http:/ master for this Standard at ULs Northbrook Office is the official document insofar as it re

6、lates to aUL service and the compliance of a product with respect to the requirements for that product and service,or if there are questions regarding the accuracy of this Standard.ULs Standards for Safety are copyrighted by UL. Neither a printed copy of a Standard, nor the distributiondiskette for

7、a Standard-on-Diskette and the file for the Standard on the distribution diskette should bealtered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding thoseStandards shall remain the sole and exclusive property of UL.All rights reserved. No part of this publication

8、may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwisewithout prior permission of UL.Revisions of UL Standards for Safety are issued from time to time. A UL Standard for Safety is currentonly if it incorpo

9、rates the most recently adopted revisions.UL provides this Standard as is without warranty of any kind, either expressed or implied, including butnot limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequent

10、ial, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this Standard, even if UL or an authorized UL representative has been advised of thepossibility of such damage. In no event shall ULs liabilit

11、y for any damage ever exceed the price paid forthis Standard, regardless of the form of the claim.AUGUST 29, 2008 UL 1248 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUL will attempt to answer support requests concerning electronic versi

12、ons of its Standards. However, thissupport service is offered on a reasonable efforts basis only, and UL may not be able to resolve everysupport request. UL supports the electronic versions of its Standards only if they are used under theconditions and operating systems for which it is intended. ULs

13、 support policies may change fromtime-to-time without notification.UL reserves the right to change the format, presentation, file types and formats, delivery methods andformats, and the like of both its printed and electronic Standards without prior notice.Purchasers of the electronic versions of UL

14、s Standards for Safety agree to defend, indemnify, and holdUL harmless from and against any loss, expense, liability, damage, claim, or judgement (includingreasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing anelectronic Standard on the purchasers c

15、omputer system.If a single-user version electronic Standard was purchased, one copy of this Standard may be stored onthe hard disk of a single personal computer, or on a single LAN file-server or the permanent storagedevice of a multiple-user computer in such a manner that this Standard may only be

16、accessed by one userat a time and for which there is no possibility of multiple concurrent access.If a multiple-user version electronic Standard was purchased, one copy of the Standard may be stored ona single LAN file-server, or on the permanent storage device of a multiple-user computer, or on an

17、Intranetserver. The number of concurrent users shall not exceed the number of users authorized.Electronic Standards are intended for on-line use, such as for viewing the requirements of a Standard,conducting a word search, and the like. Only one copy of the Standard may be printed from eachsingle-us

18、er version of an electronic Standard. Only one copy of the Standard may be printed for eachauthorized user of a multiple-user version of an electronic Standard. Because of differences in thecomputer/software/printer setup used by UL and those of electronic Standards purchasers, the printedcopy obtai

19、ned by a purchaser may not look exactly like the on-line screen view or the printed Standard.An employee of an organization purchasing a UL Standard can make a copy of the page or pages beingviewed for their own fair and/or practical internal use.The requirements in this Standard are now in effect,

20、except for those paragraphs, sections, tables, figures,and/or other elements of the Standard having future effective dates as indicated in the note following theaffected item. The prior text for requirements that have been revised and that have a future effective dateare located after the Standard,

21、and are preceded by a SUPERSEDED REQUIREMENTS notice.New product submittals made prior to a specified future effective date will be judged under all of therequirements in this Standard including those requirements with a specified future effective date, unlessthe applicant specifically requests that

22、 the product be judged under the current requirements. However, ifthe applicant elects this option, it should be noted that compliance with all the requirements in thisStandard will be required as a condition of continued Listing and Follow-Up Services after the effectivedate, and understanding of t

23、his should be signified in writing.Copyright 2008 Underwriters Laboratories Inc.AUGUST 29, 2008 UL 1248tr2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULThis Standard consists of pages dated as shown in the following checklist:Page Date1.Augu

24、st 29, 20082-45 December 8, 200646August 29, 200847-58 .December 8, 2006AUGUST 29, 2008 UL 1248 tr3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULAUGUST 29, 2008 UL 1248tr4No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

25、 REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULDECEMBER 8, 2006(Title Page Reprinted: August 29, 2008)1UL 1248Standard for Engine-Generator Assemblies for Use in RecreationalVehiclesFirst Edition July, 1978Second Edition August, 1993Third EditionDecember 8, 2006An effective date included as

26、a note immediately following certain requirementsis one established by Underwriters Laboratories Inc.Revisions of this Standard will be made by issuing revised or additional pagesbearing their date of issue. A UL Standard is current only if it incorporates themost recently adopted revisions, all of

27、which are itemized on the transmittal noticethat accompanies the latest set of revised requirements. Comments or proposalsfor revisions on any part of the Standard may be submitted to UL at any time.Proposals should be submitted via a Proposal Request in ULs On-LineCollaborative Standards Developmen

28、t System (CSDS) at http:/.COPYRIGHT 2006, 2008 UNDERWRITERS LABORATORIES INC.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULDECEMBER 8, 2006UL 12482No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBU

29、TION WITHOUT PERMISSION FROM ULCONTENTSINTRODUCTIONALL UNITS1 Scope .62 General 72.1 Units of measurement .72.2 Undated references .72.3 Terminology .73 Components 74 Instructions and Drawings 8CONSTRUCTIONALL UNITS5 Protection Against Personal Injury 85.1 General .85.2 Enclosures and guards 95.3 Sh

30、arp edges 135.4 Provision for mounting .135.5 Temperature 13MECHANICAL SYSTEM6 Fuel Systems Gasoline .146.1 Tanks and pumps .146.2 Fuel lines and fittings 146.3 Nonmetallic parts 156.4 Corrosion resistance .156.5 Carburetors .167 Fuel Systems Liquefied Petroleum Gas .167.1 General 167.2 Containers 1

31、77.3 Gauges 187.4 Fuel lines and fittings 197.5 Vaporizers 207.6 Safety control and relief devices .207.7 Nonmetallic parts 217.8 Corrosion resistance .228 Exhaust System .22ELECTRICAL SYSTEM9 Enclosure .229.1 General 229.2 Battery compartment .2610 Assembly 2611 Wiring .2711.1 Field connection .27D

32、ECEMBER 8, 2006 UL 1248 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL11.2 Wiring terminals and leads 2811.3 Factory wiring 3011.4 Internal high-voltage wiring 3011.5 Separation of circuits .3212 Electrical Components .3312.1 Live parts .33

33、12.2 Electrical insulation .3312.3 Insulation systems 3412.4 Windings 3412.5 Nonmetallic functional parts .3412.6 Capacitors .3512.7 Transformers and reactors 3512.8 Resistors 3512.9 Switches and controllers 3512.10 Receptacles 3513 Bonding for Grounding 3613.1 Internal parts 3613.2 Generator frame

34、.3814 Generator Protection 3915 Generator Output Circuit Protection .3915.1 Ground fault circuit interrupter .3916 Spacings 3916.1 General .3916.2 Barriers and liners 41PERFORMANCEALL UNITS17 General 4118 Test Installation .4219 Instrumentation .4220 Temperature Test .43MECHANICAL SYSTEMS21 Blocked

35、Inlet Test .4522 Backfire-Deflector Test 4523 10-Day Moist Ammonia-Air Stress Cracking Test .4624 Overspeed Test 4725 LP-Gas Container Load Tests 47ELECTRICAL SYSTEMS26 Output Waveform Analysis .4727 Variation in Output Voltage and Frequency Test 4728 Dielectric Voltage Withstand Test .4929 Overtemp

36、erature Protection 4929.1 Maximum temperature test 4929.2 Overload and endurance operation tests 5029.3 Limited short circuit test .5030 Overload Test 5031 Rain Test 51DECEMBER 8, 2006UL 12484UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULMAN

37、UFACTURING AND PRODUCTION TESTS32 General 5433 Dielectric Voltage Withstand Test .5434 Generator Output Measurements .54MARKING35 General 5536 Installation and Operating Instructions .5636.1 Mechanical 5636.2 Electrical 57DECEMBER 8, 2006 UL 1248 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER R

38、EPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULINTRODUCTIONALL UNITS1 Scope1.1 These requirements cover the fire and casualty aspects associated with the mechanical performanceand the electrical features of engine driven generator assemblies intended for installation in recreationalvehicles.1.

39、2 These requirements cover generators rated: 15 kilowatts or less, 115 volts, 2-wire single phase; 240volts, 2-wire single phase; 115/230 volts, 3-wire single phase; 3 or 4 wire, any voltage, three phase. Thegenerators may incorporate alternator or direct current generator sections for supplying ene

40、rgy to batterycharging circuits. Only generators having systems voltages of less than 150 volts to ground are permittedfor noncommercial applications.1.3 These requirements cover both open and totally-enclosed generators.1.4 A totally-enclosed generator is so enclosed as to prevent the free exchange

41、 of air between the insideand the outside of the enclosure for windings but not sufficiently enclosed as to be airtight.1.5 A generator having ventilating openings that permit the passage of external cooling air over andaround the windings is an open generator.1.6 These requirements cover generator

42、parts and combinations of such parts.1.7 These requirements do not cover generators for use in hazardous locations as defined in the NationalElectrical Code.1.8 These requirements cover only the identified hazard aspects of motor-generator assemblies intendedfor use with recreational vehicles. These

43、 requirements do not cover other possible hazard aspects of suchequipment.1.9 A product that contains features, characteristics, components, materials, or systems new or differentfrom those in use when the standard was developed and that involves a risk of fire, electric shock, or injuryto persons s

44、hall be evaluated using the appropriate additional component and end-product requirementsas determined necessary to maintain the level of safety for the user of the product as originally anticipatedby the intent of this standard.DECEMBER 8, 2006UL 12486UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURT

45、HER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL2 General2.1 Units of measurement2.1.1 If a value for measurement is followed by a value in other units, in parentheses, the second valuemay be only approximate. The first stated value is the requirement.2.2 Undated references2.2.1 Any undate

46、d reference to a code or standard appearing in the requirements of this standard shallbe interpreted as referring to the latest edition of that code or standard.2.3 Terminology2.3.1 The term product as used in this Standard, refers to any equipment covered by this Standard.3 Components3.1 Except as

47、indicated in 3.2, a component of a product covered by this standard shall comply with therequirements for that component.3.2 A component need not comply with a specific requirement that:a) Involves a feature or characteristic not needed in the application of the component in theproduct covered by th

48、is standard, orb) Is superseded by a requirement in this standard.3.3 A component shall be used in accordance with its recognized rating established for the intendedconditions of use.3.4 Specific components are recognized as being incomplete in construction features or restricted inperformance capab

49、ilities. Such components are intended for use only under limited conditions, such ascertain temperatures not exceeding specified limits, and shall be used only under those specific conditionsfor which they have been recognized.3.5 If the manufacturer assigns a rating or an intended use to a component of a generator (for example,an integral auxiliary switch intended to control an external circuit) the component is to be evaluated forthat rating or use or both.DECEMBER 8, 2006 UL 1248 7UL COP