UL 1472-2015 UL Standard for Safety Solid-State Dimming Controls (Second Edition Reprint with revisions through and including November 10 2017).pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 1472 Solid-State Dimming ControlsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER

2、REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Solid-State Dimming Controls, UL 1472 Second Edition, Dated September 25, 2015 Summary of Topics This second edition of ANSI/UL 1472 includes the following: 1. Addition of requirements for eld replaceable actuator ass

3、emblies 2. Revising and adding requirements with respect to wall-box dimmer switches for use with LED lamp with integral driver light source 3. Addition of requirements for ground leakage current As noted in the Commitment for Amendments statement located on the back side of the title page, UL and C

4、SA are committed to updating this harmonized standard jointly. A UL effective date is one established by UL LLC and is not part of the ANSI approved standard. The revised requirements are substantially in accordance with Proposal(s) on this subject dated June 20, 2014 and February 6, 2015. All right

5、s reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expresse

6、d or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out

7、 of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the elect

8、ronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standa

9、rd on the purchasers computer system. SEPTEMBER 25, 2015 UL 1472 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SEPTEMBER 25, 2015 UL 1472 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIB

10、UTION WITHOUT PERMISSION FROM UL Solid-State Dimming Controls September 25, 2015 CSA Group CSA-C22.2 No. 184.1 Second Edition Underwriters Laboratories Inc. UL 1472 Second Edition ANSI/UL 1472-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM

11、 UL Commitment for Amendments This standard is issued jointly by the Canadian Standards Association (operating as CSA Group) and Underwriters Laboratories Incorporated (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA Group or UL at any time. Revisions to

12、this standard will be made only after processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will issue revisions to this Standard by means of a new edition or revised or additional pages bearing their date of issue. This ANSI/UL Standard for Safety consis

13、ts of the Second edition. The most recent designation of ANSI/UL 1472 as an American National Standard (ANSI) occurred on September 24, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revision

14、s on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- help/how_to_order.aspx or call toll-free 1-888-853-

15、3503. ISSN 0317-5669 Copyright 2015 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. Copyright 2015 Underwriters Laboratories Inc.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTR

16、IBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .5 1 Scope .8 2 Denitions 9 3 General requirements 10 3.1 Components 10 3.2 Normative references 10 3.3 Units of measurement 11 4 Construction .12 4.1 Polymeric materials 12 4.2 Actuating member .13 4.3 Spacings .13 4.4 Means for mounting .14 4.5 C

17、urrent-carrying parts 14 4.6 Grounding and bonding 16 4.7 Switches .17 4.8 Flush-device cover plates 17 4.9 Touch dimmers .18 5 Tests .18 5.1 Test conditions 18 5.2 Test loads 19 5.3 Overload tests 21 5.4 Endurance test 22 5.5 Temperature test 23 5.6 Dielectric voltage-withstand test .25 5.7 Air-gap

18、 switch test .26 5.8 Security of lead test .26 5.9 Torque and pull-out tests .26 5.10 Limited short-circuit test .27 5.11 D-C offset test .28 5.12 Mold stress-relief distortion test 28 5.13 Leakage current test for touch dimmers .29 5.14 Leakage current test 29 5.15 Grounding and bonding conductor t

19、est .30 5.16 Field Replaceable Actuator Assembly Test 30 6 Manufacturing and production tests 30 6.1 Dielectric voltage-withstand test .30 7 Markings 31 7.1 General 31 7.2 Field wiring terminals 33 7.3 Cautionary 34 ANNEX A Standards for Components A1 Component Standards A1 SEPTEMBER 25, 2015 CSA-C2

20、2.2 NO. 184.1 UL 1472 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL ANNEX B French translations and markings SEPTEMBER 25, 2015 CSA-C22.2 NO. 184.1 UL 1472 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION W

21、ITHOUT PERMISSION FROM UL Preface This is the common UL and CSA Standard for Solid-State Dimming Controls. It is the second edition of both CSA-C22.2 No. 184 and UL 1472. This common Standard was prepared by a Task Force comprised of members representing CSA, UL, NEMA (National Electrical Manufactur

22、ers Association) and the EFC (Electro-Federation of Canada). This standard includes all items presently covered in C22.2 No. 184-M1988 except the following: a) Lighting controls without integral switching (disconnecting control). b) Devices used as table mounted unit to which a portable luminaire ca

23、n be temporarily connected. c) Devices installed in lampholders. d) Devices permanently installed in the supply line of a lamp. e) Direct plugin devices. The above will be accommodated either in a new edition of C22.2 No. 184, or in future revisions of this standard. Note: Although the intended prim

24、ary application of this Standard is stated in its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose. Level of Harmonization This Standard is published as an identical standard for UL and CSA. An identi

25、cal standard is a standard that is the same in technical content except for conicts in Codes and Governmental Regulations. Presentation shall be word for word except for editorial changes. Interpretations The interpretation by the SDO of an identical or equivalent standard shall be based on the lite

26、ral text to determine compliance with the standard in accordance with the procedural rules of the SDO. If more than one interpretation of the literal text has been identied, a revision shall be proposed as soon as possible to each of the SDOs to more accurately reect the intent. CSA Group Effective

27、Date The effective date for CSA Group will be announced through a CSA Informs or CSA Group Certication Notice. UL Effective Date A UL effective date is one established by UL LLC and is not part of the ANSI approved standard. SEPTEMBER 25, 2015 CSA-C22.2 NO. 184.1 UL 1472 5UL COPYRIGHTED MATERIAL NOT

28、 AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL SDO Forewords The UL Foreword is no longer located within the UL Standard. The CSA Foreword is included as an SDO-specic page in the CSA version of this co-published standard. The current version of the UL Foreword is lo

29、cated on ULStandardsInfoNet at: http:/ SEPTEMBER 25, 2015 CSA-C22.2 NO. 184.1 UL 1472 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL This page intentionally left blank. SEPTEMBER 25, 2015 CSA-C22.2 NO. 184.1 UL 1472 7UL COPYRIGHTED MATERIA

30、L NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Solid-State Dimming Controls 1 Scope 1.1 These requirements cover permanently installed devices, hereafter referred to as dimmers, that employ a dimming function intended for control of lighting loads of the magneti

31、c ballast, transformer, electronic ballast, self-ballasted lamp, tungsten-lament type, or light-emitting-diode (LED), and are intended to be installed in a wallbox or are provided with an enclosure for ush or surface mounting in accordance with the Canadian Electric Code, Part 1 (CEC), and the Natio

32、nal Electrical Code (NEC), ANSI/NFPA 70. 1.2 These requirements cover dimmers, other than touch dimmers, rated 600 volts ac or less, for installation on a 20-ampere or less branch circuit. 1.3 These requirements cover touch dimmers rated 120 volts ac or less for installation on a 20-ampere or less b

33、ranch circuit. 1.4 These requirements cover dimmers, including touch dimmers, and electronic switches, having a minimum power rating of 300 watts incandescent or 300 volt-amperes in increments of 50 watts or 50 volt-amperes. 1.5 Devices may have additional current ratings based upon the additional l

34、ighting loads as specied by the manufacturer. 1.6 A device incorporating other functions (for example, speed control) in addition to a dimming function is investigated on the basis of compliance with the applicable requirements for the dimming function in this Standard as well as requirements for th

35、e other functions in the applicable standards. 1.7 These requirements do not cover dimmers that use only a resistor or a transformer to perform the dimming function. 1.8 These requirements do not cover modular, cabinet or console type constructions. 1.9 These requirements do not cover dimmers intend

36、ed primarily for use in theaters. Dimmers for use in theaters are covered by the Standard for Industrial Control Equipment, UL 508/CSA C22.2 No. 14. SEPTEMBER 25, 2015 CSA-C22.2 NO. 184.1 UL 1472 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM

37、 UL 2 Denitions 2.1 The following denitions apply in this Standard. Actuating member Part of the operating mechanism that is used for the dimming control functions. This member may also be used to operate the air-gap switch. CFL Compact Fluorescent Lamp. CCFL Cold Cathode Fluorescent Lamp. Dimmer A

38、device intended to change lighting to various intensities. For the purposes of these requirements, the term dimmer refers to all products covered by this Standard. Electronic ballast A ballast, generally involving high-frequency switching that is controlled by active components (transistors, thyrist

39、ors, and the like), and with the lamp ballasting impedance provided by a series capacitive or inductive reactance appropriate for the high switching frequency. “Ballast” also refers to other drivers or supplies that operate lamp technologies other than uorescent. Electronic switch A solid-state devi

40、ce that performs strictly an on-off function and meets the requirements of this standard including the air-gap switch requirement. Grounding/bonding conductor A conductor that is dened in the National Electrical Code (NEC) as an Equipment Grounding Conductor, and a conductor that is dened in the Can

41、adian Electrical Code (CE Code), Part I, as a Bonding Conductor. Lamp, self-ballasted A device such as a CFL, CCFL, LED, etc. that is provided with a lamp base and incorporating a nonreplaceable light source and any additional elements such as an electronic ballast necessary for starting and stabili

42、zing operation of the light source, which cannot be dismantled without being permanently damaged. Off position The air-gap switch is in the open position. Opposite polarity A difference of potential between two points where shorting of these two points would result in a condition involving overload,

43、 rupturing of printed wiring board tracks, components, fuses, or the like. Touch dimmer A device using circuitry for touch actuation in accordance with Clauses 4.9 and 5.13. Examples of such circuitry are non-isolated sensing or conductively connected dead metal. Type I dimmer A dimmer in which the

44、air-gap switch is used to energize preset lighting levels. Type II dimmer UL A dimmer with an air-gap switch that opens and closes the load circuit at the minimum output voltage setting only. Type IIa dimmer A dimmer with an air-gap switch that opens and closes the load circuit at the maximum output

45、 voltage setting only. Type III dimmer A dimmer incorporating solid-state components providing preestablished rectied output settings. Type IV dimmer A dimmer not covered by Types I III. SEPTEMBER 25, 2015 CSA-C22.2 NO. 184.1 UL 1472 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION O

46、R DISTRIBUTION WITHOUT PERMISSION FROM UL 3 General requirements 3.1 Components 3.1.1 Except as indicated in Clause 3.1.2, a component of a product covered by this standard shall comply with the requirements for that component. See Annex A for a list of Standards covering components generally used i

47、n the products covered by this Standard. A component shall comply with both the Underwriters Laboratories Inc. and Canadian Standards Association Standards for the component. 3.1.2 A component need not comply with a specic requirement that: a) involves a feature or characteristic not needed in the a

48、pplication of the component in the product covered by this Standard, or b) is superseded by a requirement in this Standard. 3.1.3 A component shall be used in accordance with its rating for the intended conditions of use. 3.1.4 Specic components are incomplete in construction features or restricted

49、in performance capabilities. Such components are intended for use only under limited conditions, such as certain temperatures not exceeding specied limits, and shall be used only under those specic conditions. 3.2 Normative references 3.2.1 Where reference is made to other publications, such reference shall be considered to refer to the latest edition and all amendments published to that edition up to the t