UL 1564 CRD-2017 UL Standard for safety Industrial Battery Chargers - Section Paragraph Reference New Supplement SB Subject Additional Requirements for Lithium Ion Batteries used .pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULUNDERWRITERS LABORATORIES INC. CERTIFICATION REQUIREMENT DECISIONThis Certification Requirement Decision is prepared by UL LLC. It is normative for the applicable ULProduct Certification Program(

2、s); however, it is currently not part of the UL Standard(s) referencedbelow.Product Category (CCN): BBHZ23Standard Number: UL 1564Standard Title: Standard for Industrial Battery ChargersEdition Date: May 14, 2015Edition Number: 4Section / Paragraph Reference: New Supplement SBSubject: Additional Req

3、uirements for Lithium Ion Batteries used with IndustrialBattery Chargers.DECISION:The requirements below include new definitions, performance test considerations, and procedures for theevaluation of Lithium Ion batteries with Industrial battery chargers.SUPPLEMENT SB INDUSTRIAL BATTERY CHARGERS INTE

4、NDED FOR CHARGING LITHIUM ION(Li-ion) CHEMISTRIESGENERALSB1 ScopeSB1.1 These requirements supplement and in some cases modify the requirements in Sections149and Supplement SA. This equipment is intended for the charging of batteries that comply withUL 2271 (BBCA) Batteries for Use in Light Electric

5、Vehicle (LEV) Applications orUL 2580 (BBAS) Batteries for Use in Electric Vehicles.PERFORMANCESB2 Power Input TestSB2.1 A product having an output rating of more than 20 amperes is to be tested with its intended battery.SB3 Temperature TestSB3.1 During the temperature test of a product using a batte

6、ry load, the battery shall be discharged asindicated in 29.3 then charged until temperatures on the product reach a maximum and begin to decrease.The temperature test is then to be continued using a second battery, also discharged as indicated in 29.3,until maximum temperatures are attained. A produ

7、ct provided with a timer and a marked charging timebased on the ampere-hour capacity of the battery is to be tested for the marked time period.Exception: A second battery is not used for products which provide a constant charging current or havea marked charging time such that only one battery can b

8、e charged during an 8-hour period.SB4 Intermediate Abnormal TestUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULSB4.1 A product tested using a battery as a load as described in SB3.1 shall be subjected to anintermediate abnormal test described

9、 in 31.2 immediately following the temperature test. The product shallnot emit flame or molten metal or result in a risk of fire or electric shock during the test. The test is to befollowed by a dielectric voltage-withstand test, as required by 32.1.1(a), applied between the primary andsecondary win

10、dings of the transformer.Exception: A product that is current limited during normal charging is not required to be subjected to acontinuous load test.SB5 Reverse polaritySB5.1 The external output leads are to be connected in reverse polarity to a fully-charged battery. Theproduct is then to be conne

11、cted to its maximum test voltage see Table 27.1 and operated until theultimate condition is observed, or 4 hours if cycling of an automatically reset protector occurs. Fuses andother protective devices provided as part of the product are to remain in the circuit.MARKINGSSB6 GeneralSB6.1 A product sh

12、all be marked with charging instructions such as, number of cells, and ampere-hourrating.SB6.2 A product or the User manual shall provide sufficient information concerning any conditionnecessary to ensure that, when used as prescribed by the manufacturer, the equipment is unlikely topresent a hazard

13、 within the meaning of this standard.RATIONALE FOR DECISION:The current requirements for UL 1564 are based on lead-acid battery technology. The increasing demandfor lithium ion batteries in Industrial Applications requires additional considerations. This CRD introducesadditional definitions, clarifi

14、cations, and testing requirements for industrial battery chargers intended tocharge lithium ion batteries.The requirements of UL 1564 predate the battery chemistries available at this time. This CRD is intendedto add additional testing and certification requirements for industrial battery chargers i

15、ntended to chargeLithium Ion batteries.Copyright 2017 UL LLCUL LLC, in performing its functions in accordance with its objectives, does not guarantee or warrant thecorrectness of Certification Requirement Decisions it may issue or that they will be recognized or adoptedby anyone. Certification Requi

16、rement Decisions are the opinion of UL LLC. in practically applying therequirements of the standard. They do not represent formal interpretations of the standard underAmerican National Standards Institute (ANSI) processes. UL LLC shall not be responsible to anyone forthe use of or reliance upon Cert

17、ification Requirement Decisions by anyone. UL LLC shall not incur anyobligation or liability for damages, including consequential damages, arising out of or in connection withthe use or reliance upon Certification Requirement Decisions. The electronic version of the CertificationRequirement Decision

18、 is the current version and previously printed copies may be outdated.STANDARD NUMBER: UL 1564 -2-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULThis document is published as a service to ULs certification customersSTANDARD NUMBER: UL 1564 -3-UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULSTANDARD NUMBER: UL 1564 -4-No Text on This Page