UL 330-2009 UL Standard for Safety Hose and Hose Assemblies for Dispensing Flammable Liquids (Seventh Edition Reprint with revisions through and including August 23 2013)《用于配送可燃液体的.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 330 Hose and Hose Assemblies for Dispensing Flammable LiquidsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL

2、 NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hose and Hose Assemblies for Dispensing Flammable Liquids, UL 330 Seventh Edition, Dated December 16, 2009 SUMMARY OF TOPICS These revisions to ANSI/UL 330 include the following: 1. Revisio

3、n to paragraph 30.2 regarding low temperature marking on hose 2. Revision to the Repeated Bending Test (Filled) with respect to hose assemblies 3. Clarication of the term “vapor recovery hose” 4. Revisions regarding vacuum-assist vapor recovery hose assemblies 5. Revision to the preconditioning proc

4、edure for Repeated Bending (Filled) The revised requirements are substantially in accordance with Proposal(s) on this subject dated June 7, 2013. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mec

5、hanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for

6、 any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such d

7、amage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage

8、, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures,

9、and/or other elements of the Standard having future effective dates as indicated in the note following the affected item. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice.

10、 AUGUST 23, 2013 UL 330 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 23, 2013 UL 330 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 16,

11、 2009 (Title Page Reprinted: August 23, 2013) 1 UL 330 Standard for Hose and Hose Assemblies for Dispensing Flammable Liquids The First edition was titled the Standard for Construction of Rubber Hose for Conducting Gasoline The Second edition was titled the Standard for 3/4-, 1-, and 1-1/4-inch Hose

12、 for Conducting Gasoline The Third edition was titled the Standard for Hose for Conducting Gasoline The Fourth edition was titled the Standard for Gasoline Hose The Fifth edition was titled the Standard for Hose and Hose Assemblies for Dispensing Flammable Liquids First Edition September, 1917 Secon

13、d Edition March, 1937 Third Edition July, 1950 Fourth Edition June, 1973 Fifth Edition August, 1978 Sixth Edition August, 1996 Seventh Edition December 16, 2009 This ANSI/UL Standard for Safety consists of the Seventh Edition including revisions through August 23, 2013. The most recent designation o

14、f ANSI/UL 330 as an American National Standard (ANSI) occurred on August 22, 2013. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page, or effective date information. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any

15、 time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyr

16、ights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2013 UNDERWRITERS LABORATORIES INC. ANSI/UL 330-2013UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 16, 2009 HOSE

17、AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS INTRODUCTION 1 Scope .6 2 General 7 2.1 Units of measurements 7 2.2 Undated references .7 3 Glossary

18、 .7 CONSTRUCTION 4 Tube and Cover 8 4.1 Single-line hose and double-line vapor recovery hose .8 4.2 Coaxial vapor recovery hose .8 5 Thickness of Cover 8 6 Internal Diameter .9 7 Reinforcement .10 8 Electrical Bonding 10 9 Couplings .10 PERFORMANCE 10 General 11 11 Repeated Bending Test (Empty) 11 1

19、1.1 General .11 11.2 Sample .11 11.3 Apparatus .11 11.4 Method .11 12 Hydrostatic Strength Test 13 12.1 General .13 12.2 Sample .13 12.3 Apparatus .13 12.4 Method .14 13 Resistance To External Pressure .14 13.1 General .14 13.2 Sample .14 13.3 Apparatus .14 13.4 Method .14 14 Repeated Bending Test (

20、Filled) .15 14.1 General .15 14.2 Sample .15 14.3 Apparatus .15 14.4 Method .16 15 Permeation Test (For Low Permeation Hose) 16 15.1 General .16 15.2 Test equipment 16 15.3 General test procedure and instructions .17 15.4 Samples 18 15.5 Pretest procedure 18 15.6 Preconditioning procedure .19 15.7 P

21、ermeation test procedure 19 DECEMBER 16, 2009 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 15.8 Steady state criteria 20 16 Electrical Resistance Tests for Hose Having No

22、nmetallic Electrically Conductive Materials . .21 16.1 General .21 16.2 Samples 21 16.3 Apparatus .21 16.4 Method .21 17 Leakage and Electrical Continuity Test 22 17.1 General .22 17.2 Sample .22 17.3 Apparatus .22 17.4 Method .23 18 Swivel Joint Operation Test 23 18.1 General .23 19 Pull Test .23 1

23、9.1 General .23 19.2 Sample .23 19.3 Equipment .24 19.4 Method .24 20 Adhesion Test 24 20.1 General .24 20.2 Sample .25 20.3 Apparatus .25 20.4 Method .25 21 Deformation Test .25 22 Kink Test 26 23 Tensile Strength and Elongation Tests 26 23.1 General .26 23.2 Samples 26 23.3 Apparatus .27 23.4 Meth

24、od .27 24 Accelerated Air Oven Aging Test .28 24.1 General .28 24.2 Samples 28 24.3 Apparatus .28 24.4 Method .28 24.5 O-rings 29 25 Ozone Exposure Test .29 25.1 General .29 25.2 Samples 29 25.3 Apparatus .29 25.4 Method .29 26 Ultraviolet Light and Water Exposure Test .30 26.1 General .30 26.2 Samp

25、le .30 26.3 Apparatus .30 26.4 Method .30 27 Immersion Tests 31 27.1 Tensile strength and ultimate elongation 31 27.2 Samples 31 27.3 Apparatus .32 27.4 Method .32 27.5 Volume change 32 27.6 O-rings, gaskets, and sealing materials .34 DECEMBER 16, 2009 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMAB

26、LE LIQUIDS - UL 330 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 28 Low Temperature Test 34 28.1 General .34 28.2 Sample .35 28.3 Apparatus .35 28.4 Method .35 28.5 O-rings 35 MANUFACTURING AND PRODUCTION TESTS 29 General 35 MARKING 30 D

27、etails .36 DECEMBER 16, 2009 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTRODUCTION 1 Scope 1.1 These requirements cover hose and hose assemblies, including vapor reco

28、very hose and assemblies, for use on dispensing devices for ammable liquids. A ammable liquid hose assembly consists of exible hose and ttings suitable for attachment to ammable liquid dispensing equipment. For the purpose of this Standard ammable liquids are gasoline and diesel fuel. The term “gaso

29、line” includes gasoline with small amounts of additives such as detergents, solvents for detergents, and anti-icing chemicals and gasoline with up to 15 percent ethanol. 1.2 Hose assemblies are intended for use in accordance with the Automotive and Marine Service Station Code of National Fire Protec

30、tion Association, NFPA 30A. 1.2 revised February 8, 2013 1.3 These requirements cover hose used on dispensing devices for fuels not covered in 1.1 when found by investigation to have the required resistance to these fuels. 1.4 These requirements cover hose and hose assemblies (hose with couplings at

31、tached) in sizes up to and including 1-1/2 inches (38.1 mm). 1.5 Hose for conveying liquid fuel is intended for use at a maximum working pressure of 50 psig (345 kPa). Hose for conveying vapors of fuel is intended for use at a maximum working pressure of 0.5 psig (3.4 kPa), including slight negative

32、 pressures from vapor assist systems. 1.6 These requirements cover hose and hose assemblies for use at temperatures down to minus 40C (minus 40F) or minus 54C (minus 65F). 1.7 These requirements also cover fuel hose assemblies designated as “low permeation”, intended for use on dispensing devices fo

33、r ammable liquids. For the purposes of this standard, permeation is considered to encompass fuel loss through the exible hose, fuel loss at the ttings and fuel loss at the connection between the hose assembly and the equipment to which it is intended to be attached in the dispensing system. 1.8 Thes

34、e requirements do not cover hose or hose assemblies, intended for use in automotive vehicles or in conned areas, except for locations inside the housings of dispensing devices complying with the Standard For Power-Operated Dispensing Devices For Petroleum Products, UL 87. FEBRUARY 8, 2013 HOSE AND H

35、OSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2 General 2.1 Units of measurements 2.1.1 When a value for measurement is followed by a value in other units in parentheses, the rst st

36、ated value is the requirement. 2.2 Undated references 2.2.1 Any undated reference to a code or standard appearing in the requirements of this standard shall be interpreted as referring to the latest edition of that code or standard. 3 Glossary 3.1 For the purposes of this outline, the following deni

37、tions apply. 3.2 ADJUSTED MASS LOSS The mass loss of the blank (unlled hose assembly) subtracted from the mass loss of a lled hose assembly. The purpose of this is to adjust for factors other than fuel permeation that may affect mass loss. 3.3 BALANCE VAPOR RECOVERY HOSE ASSEMBLY A coaxial hose cons

38、isting of an inner line for conveying fuel and an outer line. Fuel vapors are permitted to return to the fuel dispenser in the annular space between the two lines. 3.3 revised August 23, 2013 3.4 HOSE ASSEMBLY VOLUME (V) The total volume in cubic centimeters of a capped hose assembly, calculated as

39、follows: V=D 2 (L + 2d) p /4 in which: D = the inner diameter of the hose in centimeters, as determined in 15.5.3 L = the length of the hose in centimeters, as determined in 15.5.1 d = the depth of the cap in centimeters, as determined in 15.5.2 3.5 LEAST SQUARES FIT LINE A best t line drawn through

40、 a set of data such that the sum of the squared residuals has its least value, a residual being the difference between an observed value (data point) and the line. 3.6 PERMEATION SURFACE AREA The length of the hose as determined in 15.5.1 multiplied by the inner circumference of the hose, expressed

41、in square meters. For vacuum-assist vapor recovery hose, the length of the hose is multiplied by the inner circumference of the outer hose. For balance vapor recovery hose, the length of the hose is multiplied by the average inner circumference of the outer hose. 3.6.1 REINFORCEMENT Natural or synth

42、etic bers or fabric, or metallic wire that is wrapped, braided or spiral wound in one or more layers over the tube, intended to provide longitudinal and transverse (hoop) strength to the hose. 3.6.1 added August 26, 2011 AUGUST 23, 2013 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL

43、330 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 3.7 VACUUMASSIST VAPOR RECOVERY HOSE ASSEMBLY A coaxial hose consisting of an inner vacuum line for vapor recovery and an outer line. Fuel is dispensed through the annular space between th

44、e two lines. 3.7 revised August 23, 2013 CONSTRUCTION 4 Tube and Cover 4.1 Single-line hose and double-line vapor recovery hose 4.1.1 The tube shall be made from a material resistant to gasoline and diesel fuel. 4.1.2 The cover shall be made from a material resistant to gasoline, diesel fuel, oils,

45、and ozone. 4.1.3 The tube and cover shall be of uniform thickness, and free from pitting, blisters, or other imperfections. This requirement is not intended to exclude the use of a corrugated cover. 4.2 Coaxial vapor recovery hose 4.2.1 The tube and cover, if any, of the inner hose shall be made fro

46、m materials resistant to gasoline and diesel fuel. 4.2.2 The tube of the outer hose or a homogeneous outer hose shall be made from materials resistant to gasoline and diesel fuel. 4.2.3 The cover of the outer hose or a homogeneous outer hose shall be made from a material resistant to gasoline, diese

47、l fuel, oil, and ozone. An outer homogeneous thermoplastic hose with no separate layer of reinforcement shall also be made from a material resistant to sunlight. 4.2.4 The tube and cover shall be of uniform thickness and free from pitting, blisters, or other imperfections. This requirement is not in

48、tended to exclude the use of a corrugated tube, cover, or outer vapor hose. 5 Thickness of Cover 5.1 The thickness of the cover shall not be less than 0.047 inch (1.19 mm) when measured in accordance with 5.2 5.6. Exception: This requirement does not apply to the cover of the inner hose and the oute

49、r vapor hose of a coaxial type vapor recovery hose. 5.2 For removing irregularities in samples, the buffing machine or skiving machine outlined in the Standard Practice for Rubber Preparation of Product Pieces for Test Purposes from Products, ASTM D3183, is to be used. AUGUST 23, 2013 HOSE AND HOSE ASSEMBLIES FOR DISPENSING FLAMMABLE LIQUIDS - UL 330 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 5.3 The abrasive wheel of t