UL 60745-2-16 (ND)-2009 National Differences For UL 60745-2-16 Hand-Held Motor-Operated Electric Tools - Safety - Part 2-16 Particular Requirements for Tackers (First Edition Repri27.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60745-2-16Hand-Held Motor-Operated Electric Tools - Safety - Part 2-16: Particular Requirements forTackersUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTIO

2、N ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60745-2-16Hand-Held Motor-Operated Electric Tools - Safety - Part 2-16: Particular Requirements for TackersEdition: 1Edition Date: November 18, 20091. The revisions dated January 26, 2015 are to reaffirm the First Edition of the S

3、tandardfor Hand-Held Motor-Operated Electric Tools Safety Part 2-16: ParticularRequirements for Tackers, UL 60745-2-16, as an American National StandardAs noted in the Commitment for Amendments statement located on the back side of the titlepage, UL, CSA, and ANCE are committed to updating this harm

4、onized standard jointly. However,the revision pages dated January 26, 2015 will not be jointly issued by UL, CSA, and ANCE asthese revision pages only address UL ANSI approval dates.Please note that the national difference document incorporates all of the U.S. nationaldifferences for UL 60745-2-16Th

5、is document provides a single listing of the National Differences included in the UL adoption ofthe corresponding IEC standard.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying

6、, recording, or otherwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, either expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special

7、, incidental, consequential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof the possibility of such dama

8、ge. In no event shall ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, da

9、mage, claim, or judgment (including reasonableattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.Copyright 2015 Underwriters Laboratories Inc.JANUARY 26, 2015NATIONAL DIFFERENCES FOR UL UL 60745-2-162UL

10、COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Differences included in the UL adoptionof the corresponding IEC standard.In its IEC-based standards, UL uses the notations in

11、dicated below to identify national difference type, andthese types are additionally noted in this document. The standard may not use all types of thesedeviations.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich would compromise safety for U.S

12、. consumers and users of products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These are deviations based on the c

13、omponent standards and will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or corrections.DR - These are deviations based on the national regulatory requirements.Each national difference contains

14、 a description of what the national difference entails. Typically one of thefollowing words is used to explain how the text of the national difference is to be applied to the base IECtext:Addition / Add - An addition entails adding a complete new numbered clause, subclause, table,figure, or annex. A

15、ddition is not meant to include adding select words to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause,table, figure, or annex without any replacement text.Modification / Modify - A modification is an altering of the existing base IE

16、C text such as theaddition, replacement or deletion of certain words or the replacement of an entire clause,subclause, table, figure, or annex of the base IEC text.JANUARY 26, 2015 NATIONAL DIFFERENCES FOR UL UL 60745-2-16 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTI

17、ON WITHOUT PERMISSION FROM ULNational Differences19.102DV D2 Modify Clause 19.102 of this Part 2 by replacing the first sentence with thefollowing:Tools required to have a workpiece contact shall either:K.17.2DV DR Addition:This clause of this Part 2 is not applicable.JANUARY 26, 2015NATIONAL DIFFERENCES FOR UL UL 60745-2-164