UL 60745-2-8-2004 UL Standard for Safety Hand-Held Motor-Operated Electric Tools C Safety C Part 2-8 Particular Requirements for Shears and Nibblers (Second Edition Reprint with Re6.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 60745-2-8 Hand-Held Motor-Operated Electric Tools Safety Part 2-8: Particular Requirements for Shears and NibblersUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUT

2、ION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Hand-Held Motor-Operated Electric Tools Safety Part 2-8: Particular Requirements for Shears and Nibblers, UL 60745-2-8 Second Edition, D

3、ated March 26, 2004 Summary of Topics The revisions dated March 13, 2014 are being issued to reaffirm approval of UL 60745-2-8 as an American National Standard. No changes in requirements are involved. As noted in the Commitment for Amendments statement located on the back side of the title page, UL

4、 and CSA are committed to updating this harmonized standard jointly. However, the revision pages dated March 13, 2014 will not be jointly issued by UL and CSA as these revision pages address UL ANSI approval dates only. Text that has been changed in any manner or impacted by ULs electronic publishin

5、g system is marked with a vertical line in the margin. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides t

6、his Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of pro

7、ts, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this S

8、tandard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or devi

9、ation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having future effective dates as indicated in the pre

10、face. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. MARCH 13, 2014 UL 60745-2-8 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITH

11、OUT PERMISSION FROM UL MARCH 13, 2014 UL 60745-2-8 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Canadian Standards Association CAN/CSA-C22.2 No. 60745-2-8-04 Second Edition (IEC 60745-2-8:2003, IDT) Underwriters La

12、boratories Inc. UL 60745-2-8 Second Edition Hand-Held Motor-Operated Electric Tools Safety Part 2-8: Particular Requirements for Shears and Nibblers March 26, 2004 (Title Page Reprinted: March 13, 2014) This national standard is based on publication IEC 60745-2-8, Second Edition (2008-05). This amen

13、dment is an adoption of IEC Amendment 1(2008) to publication IEC 60745-2-8, Second Edition (2005). ANSI/UL 60745-2-8-2009 (R2014) Approved byUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jo

14、intly by the Canadian Standards Association (CSA) and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA or UL at any time. Revisions to this standard will be made only after processing according to the standards development p

15、rocedures of CSA and UL. CSA and UL will issue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ISBN 1-55397-463-8 2004 CSA Group All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prio

16、r permission of the publisher. To purchase CSA Standards and related publications, visit CSAs Online Store at www.ShopCSA.ca or call toll-free 1-800-463-6727 or 416-747-4004. Copyright 2014 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electroni

17、c copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. The most recent designation of ANSI/UL 60745-2-8 as a Reaffirmed American National Standard (ANS) occurred

18、on March 13, 2014. The ANSI approval for this standard does not include the Cover Page, Transmittal Pages, Title Page, Preface Page, National Difference Page or IEC Foreword. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submi

19、tted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CO

20、NTENTS Preface .5 FOREWORD 7 1 Scope 10 2 Normative references .10 3 Terms and Denitions 10 4 General requirements 10 5 General conditions for the tests 10 6 Void 10 7 Classication 10 8 Marking and instructions 11 9 Protection against access to live parts 11 10 Starting 11 11 Input and current .11 1

21、2 Heating 11 13 Leakage current 11 14 Moisture resistance .11 15 Electric strength 11 16 Overload protection of transformers and associated circuits 11 17 Endurance .11 18 Abnormal operation .12 19 Mechanical hazards .12 20 Mechanical strength .12 21 Construction .12 22 Internal wiring 12 23 Compone

22、nts .12 24 Supply connection and external exible cords 12 25 Terminals for external conductors .12 26 Provision for earthing 12 27 Screws and connections .12 28 Creepage distances, clearances and distances through insulation 12 29 Resistance to heat, re and tracking 13 30 Resistance to rusting 14 31

23、 Radiation, toxicity and similar hazards .14 Annexes Annex K (normative) Battery Tool and Battery Packs Annex L (normative) Battery Tools and Battery Packs Provided with Mains Connection or Non-Isolated Sources Bibliography MARCH 13, 2009 CAN/CSA-C22.2 NO. 60745-2-8-04 UL 60745-2-8 3UL COPYRIGHTED M

24、ATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MARCH 13, 2009 CAN/CSA-C22.2 NO. 60745-2-8-04 UL 60745-2-8 4 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the c

25、ommon CSA and UL standard for hand-held motor-operated electric tools. It is the second edition of CAN/CSA-C22.2 No. 60745-2-8 and the second edition of UL 60745-2-8. This standard is an adoption of IEC 60745-2-8, second edition. The rst edition of this standard was designated CAN/CSA-C22.2 No. 745-

26、2-8/UL 745-2-8. This Standard CAN/CSA-C22.2 No. 60745-2-8/UL 60745-2-8, second edition, supersedes: a) the rst edition CAN/CSA-C22.2 No. 745-2-8/UL 745-2-8 published in 1995; and b) CAN/CSA-C22.2 No. 745-4-8/UL 745-4-8, (requirements for battery tools and battery packs are now incorporated into the

27、requirements of CAN/CSA-C22.2 No. 60745-2-8, second edition, and UL 60745-2-8, second edition). The standard number has been aligned to correspond with the equivalent IEC 60745-2-8 standard. This common standard was prepared by the Canadian Standards Association (CSA) and Underwriters Laboratories I

28、nc. (UL). This standard was reviewed by the CSA Subcommittee on Portable Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA

29、 Technical Committee. This standard has been approved as a National Standard of Canada by the Standards Council of Canada and has been approved by the American National Standards Institute (ANSI) as an American National Standard. Note: Although the intended primary application of this standard is st

30、ated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. A UL standard is current only if it incorporates the most recently adopted revisions, all of which are itemized on the transmittal notice

31、that accompanies the latest set of revised requirements. Where reference is made to a specic number of samples to be tested, the specied number shall be considered a minimum quantity. Level of harmonization This standard adopts the IEC text. This standard is published as an equivalent standard for C

32、SA and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for codes and governmental regulations as well as those recognized as being in accordance with NAFTA Article 905, for example because of

33、fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country considers appropriate. Presentation is word for word except for editorial changes. MARCH 26, 2004 CAN/CSA-C22.2 NO. 60745-2-8-04 UL 60745-2-8 5UL COPYRIGHT

34、ED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Interpretations The interpretation by the standards development organization of an identical or equivalent standard is based on the literal text to determine compliance with the standard in accordance with

35、 the procedural rules of the standards development organization. If more than one literal interpretation has been identied, a revision is to be proposed as soon as possible to each of the standards development organizations to more accurately reect the intent. CSA effective date The effective date f

36、or CSA International will be announced through CSA Informs or a CSA certication notice. UL effective date The effective date for UL 60745-2-8, second edition, is October 31, 2012. Between the present and October 31, 2012, new product submittals to UL must be evaluated under all requirements in this

37、Standard or, if requested in writing, evaluated under presently effective requirements only. The presently effective requirements are contained in the rst edition of UL 745-2-8. As of October 31, 2012, all products Listed or Recognized by UL shall comply with the requirements in this standard. A UL

38、effective date is one established by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. MARCH 13, 2009 CAN/CSA-C22.2 NO. 60745-2-8-04 UL 60745-2-8 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTERNATIONAL ELEC

39、TROTECHNICAL COMMISSION HAND-HELD MOTOR-OPERATED ELECTRIC TOOLS SAFETY PART 2-8: PARTICULAR REQUIREMENTS FOR SHEARS AND NIBBLERS FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC Na

40、tional Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic elds. To this end and in addition to other activities, IEC publishes International Standards, Technical Specications, Technical Reports, Publicl

41、y Available Specications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and nongovernmental

42、 organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on techn

43、ical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IE

44、C National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international unifor

45、mity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) I

46、EC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors,

47、 employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out

48、of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to

49、 the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. This part of International Standard IEC 60745-2-8 has been prepared by sub-committee 61F: Safety of hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household and similar electrical appliances. This consolidated version of IEC 60745-2-8 con