UL 60939-3-2016 UL Standard for Safety Passive Filter Units for Electromagnetic Interference Suppression C Part 3 Passive Filter Units for Which Safety Tests are Appropriate (Firstnc.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 60939-3 Passive Filter Units for Electromagnetic Interference Suppression Part 3: Passive Filter Units for Which Safety Tests are Appropriate STANDARD FOR SAFETYUL COPYRIGHTED MATERIAL NOT A

2、UTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Passive Filter Units for Electromagnetic Interference Suppression Part 3: Passive Filter

3、Units for Which Safety Tests are Appropriate, UL 60939-3 First Edition, Dated July 22, 2016 Summary of Topics The adoption of IEC 60939-3, Passive Filter Units for Electromagnetic Interference Suppression Part 3: Passive Filter Units for Which Safety Tests are Appropriate (rst edition, issued by the

4、 IEC August 2015) as a new IEC-based UL standard, UL 60939-3. This rst edition of ANSI/UL 60939-3 reects the latest approval date as an American National Standard. Revisions have been issued to include the National Differences that achieved consensus on July 5, 2016. The new requirements are substan

5、tially in accordance with Proposal(s) on this subject dated May 6, 2016. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of

6、 UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, inc

7、luding loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the pri

8、ce paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from

9、 any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. AUGUST 22, 2016 UL 60939-3 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 22, 2016 UL 60939-3 tr2 No Text on T

10、his PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 22, 2016 (Title Page Reprinted: August 22, 2016) 1 UL 60939-3 Standard for Passive Filter Units for Electromagnetic Interference Suppression Part 3: Passive Filter Units for Which

11、Safety Tests are Appropriate First Edition July 22, 2016 This ANSI/UL Standard for Safety consists of the First Edition including revisions through August 22, 2016. The most recent designation of ANSI/UL 60939-3 as an American National Standard (ANSI) occurred on July 22, 2016. ANSI approval for a s

12、tandard does not include the Cover Page, Transmittal Pages, Title Page or Preface. The National Difference Page and IEC Foreword are also excluded from the ANSI approval of IEC-based standards. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Propos

13、als should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, owners

14、hips, and rights regarding those Standards shall remain the sole and exclusive property of UL. COPYRIGHT 2016 UNDERWRITERS LABORATORIES INC. ANSI/UL 60939-3-2016UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 22, 2016 UL 60939-3 2 No

15、Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface (UL) 6 NATIONAL DIFFERENCES .7 FOREWORD 8 1 General .10 1.1 Scope 10 1.2 Normative references 11 1.3 Information to be given in a detail specication 12 1.4 Ter

16、ms and denition .14 1.5 Marking 19 1.6 Components 21 1.7 Overcurrent protective devices 21 1.8 Wiring and Insulation 22 1.9 Protective Bonding Conductors 22A 1.10 Corrosion 22C 1.11DV.1 Live parts 22C 1.11DV.2 Switches and controllers 22D 1.11DV.3 Printed wiring boards .22D 2 Preferred ratings and c

17、haracteristics 22D 2.1 Preferred characteristics 22D 2.2 Preferred values of ratings 23 3 Test plan for safety tests 24 3.1 Structurally similar lters .24 3.2 Safety approval procedure 24 3.3 Requalication tests .25 4 Test and measurement procedures 27 4.1 General 27 4.2 Visual examination and check

18、 of dimensions .29 4.3 Inductance measurement .32 4.4 EARTH INDUCTORS incorporated in lters .33 4.5 Capacitance 33 4.6 INSERTION LOSS 33 4.7 Insulation resistance .34 4.8 Voltage proof .40 4.9 DC line resistance or voltage drop at RATED CURRENT 43 4.10 Discharge resistance .44 4.11 Robustness of ter

19、minations 45 4.12 Resistance to soldering heat .48 4.13 Solderability (for performance only) .49 4.14 Rapid change of temperature (for performance only) .50 4.15 Vibration (for performance only) 51 4.16 Shock (for performance only) 52 4.17 Container sealing (for performance only) 53 4.18 Climatic se

20、quence 53 4.19 Damp heat, steady state 56 4.20 Temperature rise .57 4.21 Current overload .60 4.22 LEAKAGE CURRENT .60A AUGUST 22, 2016 UL 60939-3 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 4.22DV.1 Leakage current test 60A 4.23 PROTEC

21、TIVE CONDUCTOR RESISTANCE .60E 4.24 Impulse voltage 61 4.25 Endurance 63 4.26 Charge and discharge (for performance only) 66 4.27 PASSIVE FLAMMABILITY 70 4.28 ACTIVE FLAMMABILITY .71 4.29 Solvent resistance of the marking 71 4.30 Component solvent resistance (for performance only) .72 Annex A (infor

22、mative) Calculation of LEAKAGE CURRENT A.1 General .73 A.2 Calculation of LEAKAGE CURRENT for 1-line lters .73 A.3 Calculation of LEAKAGE CURRENT for 2-line lters .74 A.4 Calculation of LEAKAGE CURRENT for 3-line lters .75 A.5 Calculation of LEAKAGE CURRENT for 4-line lters .77 Annex B (normative) T

23、est schedule for safety requirements only Annex C (normative) Circuit for the impulse voltage test Annex D (normative) Circuit for the endurance test Annex E (normative) Declaration of design (Condential to the manufacturer and the certication body) Annex F (informative) Safety and performance tests

24、 qualication approval Assessment level DZ Annex P (informative) Additional components and material standards Bibliography AUGUST 22, 2016 UL 60939-3 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL JULY 22, 2016 UL 60939-3 5 No Text on This

25、PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface (UL) This UL Standard is based on IEC Publication 60939-3: rst edition Passive Filter Units for Electromagnetic Interference Suppression Part 3: Passive Filter Units for Which Safet

26、y Tests are Appropriate. IEC publication 60939-3 is copyrighted by the IEC. The text, gures and tables of IEC Publication Passive Filter Units for Electromagnetic Interference Suppression Part 3: Passive Filter Units for Which Safety Tests are Appropriate, IEC 60939-3, copyright August 2015 are used

27、 in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANSI. ANSI should be contacted regarding the reproduction of any portion of the IEC material. The IEC Foreword and Introduction ar

28、e not a part of the requirements of this Standard but are included for information purposes only. Copies of IEC Publication 60939-3 may be purchased from ANSI, 11 West 42nd Street, New York, New York, 10036, (212) 642-4900. Note Although the intended primary application of this Standard is stated in

29、 its Scope, it is important to note that it remains the responsibility of the users of the Standard to judge its suitability for their particular purpose. JULY 22, 2016 UL 60939-3 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NATIONAL DIF

30、FERENCES There are ve types of National Differences as noted below. The difference type is noted on the rst line of the National Difference in the standard. The standard may not include all types of these National Differences. DR These are National Differences based on the national regulatory requir

31、ements. D1 These are National Differences which are based on basic safety principles and requirements, elimination of which would compromise safety for consumers and users of products. D2 These are national differences from IEC requirements based on existing safety practices. These requirements reec

32、t national safety practices, where empirical substantiation (for the IEC or national requirement) is not available or the text has not been included in the IEC standard. DC These are National Differences based on the component standards and will not be deleted until a particular component standard i

33、s harmonized with the IEC component standard. DE These are National Differences based on editorial comments or corrections. Each national difference contains a description of what the national difference entails. Typically one of the following words is used to explain how the text of the national di

34、fference is to be applied to the base IEC text: Addition / Add - An addition entails adding a complete new numbered clause, subclause, table, gure, or annex. Addition is not meant to include adding select words to the base IEC text. Modication / Modify - A modication is an altering of the existing b

35、ase IEC text such as the addition, replacement or deletion of certain words or the replacement of an entire clause, subclause, table, gure, or annex of the base IEC text. Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause, table, gure, or annex without a

36、ny replacement text. JULY 22, 2016 UL 60939-3 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL INTERNATIONAL ELECTROTECHNICAL COMMISSION PASSIVE FILTER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION Part 3: Passive lter units for which s

37、afety tests are appropriate FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions conce

38、rning standardization in the electrical and electronic elds. To this end and in addition to other activities, IEC publishes International Standards, Technical Specications, Technical Reports, Publicly Available Specications (PAS) and Guides (hereafter referred to as IEC Publication(s) ). Their prepa

39、ration is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and nongovernmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely wi

40、th the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant sub

41、jects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technica

42、l content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent

43、possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certication bodies provide confo

44、rmity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certication bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directo

45、rs, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising o

46、ut of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn

47、 to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60939-3 has been prepared by IEC technical committee 40: Capacitors and resistors for

48、 electronic equipment. The text of this standard is based on the following documents: FDIS Report on voting JULY 22, 2016 UL 60939-3 8 Table Continued on Next PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Table Continued 40/2387/FDIS 4

49、0/2398A/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 60939 series, published under the general title Passive lter units for electromagnetic interference suppression, can be found on the IEC website. The committee has decided that the contents of this publication will remain