UL 62275 (ND)-2010 National Differences For UL 62275 Cable Management Systems - Cable Ties for Electrical Installations (First Edition Reprint with Revisions Through and Including .pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 62275Cable Management Systems - Cable Ties for Electrical InstallationsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION

2、 FROM ULNational Differences ForUL 62275Cable Management Systems - Cable Ties for Electrical InstallationsEdition: 1Edition Date: February 26, 2010This revision is being issued to extend the UL effective date for UL 62275 to June 1, 2014. Nochanges to the requirements have been made.This document pr

3、ovides a single listing of the National Differences included in the UL adoption ofthe corresponding IEC standard.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, o

4、r otherwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, either expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental,

5、consequential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof the possibility of such damage. In no even

6、t shall ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, o

7、r judgment (including reasonableattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.Copyright Underwriters Laboratories Inc.FEBRUARY 12, 2013NATIONAL DIFFERENCES FOR UL UL 622752UL COPYRIGHTED MATERIAL NO

8、T AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Differences included in the UL adoptionof the corresponding IEC standard.In its IEC-based standards, UL uses the notations indicated below to identi

9、fy national difference type, andthese types are additionally noted in this document. The standard may not use all types of thesedeviations.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich would compromise safety for U.S. consumers and users o

10、f products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These are deviations based on the component standards and

11、will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or corrections.DR - These are deviations based on the national regulatory requirements.Each national difference contains a description of what

12、the national difference entails. Typically one of thefollowing words is used to explain how the text of the national difference is to be applied to the base IECtext:Addition / Add - An addition entails adding a complete new numbered clause, subclause, table,figure, or annex. Addition is not meant to

13、 include adding select words to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause,table, figure, or annex without any replacement text.Modification / Modify - A modification is an altering of the existing base IEC text such as theaddit

14、ion, replacement or deletion of certain words or the replacement of an entire clause,subclause, table, figure, or annex of the base IEC text.FEBRUARY 12, 2013 NATIONAL DIFFERENCES FOR UL UL 62275 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM

15、ULNational Differences2DV.1 DC Delete the normative reference to ISO 6988.2DV.2 D1 Add the following to Clause 2:2DV.2.1 In Canada, the following additional references apply:C22.1-09Canadian Electrical Code, Part ICAN/CSA-C22.2 No. 0-M91 (R2006)General requirements Canadian Electrical Code, Part IIC

16、AN/CSA-C22.2 No. 0.17-00 (R2004)Evaluation of properties of polymeric materials2DV.2.2 In the United States, the following additional references apply:National Electrical Code (NEC)ANSI/NFPA 70-2008UL 94Standard for Tests for Flammability of Plastic Materials for Parts in Devices andAppliancesUL 746

17、AStandard for Polymeric Materials Short Term PropertiesUL 746BStandard for Polymeric Materials Long Term Property EvaluationsUL 2043Fire Test for Heat and Visible Smoke Release for Discrete Products and their AccessoriesInstalled in Air-Handling Spaces2DV.2.3 In Canada and the United States, the fol

18、lowing additional references apply:IEC 60695-11-10Test flames 50 W horizontal and vertical flame test methodsISO 9227: 1990Corrosion tests in artificial atmospheres Salt spray testsIn Mexico, these references do not apply.FEBRUARY 12, 2013NATIONAL DIFFERENCES FOR UL UL 622754UL COPYRIGHTED MATERIAL

19、NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL2DV.2.4 In Mexico, the following references apply:NMX-D-122-ANCE-1973Test method for corrosion resistance of coated metal parts used in motor vehicles Saltspray (fog)NMX-J-417-ANCE-2005Wires and cables Convection labora

20、tories ovens for evaluation of electrical insulation Specifications and test methodsNMX-J-553-ANCE-2002Wires and cables Weather resistance of insulation or jacket of electrical conductors Test method3.1DV D1 Add the following note to the definition of cable tie:NOTE DV.1 In Canada and the United Sta

21、tes, Type 11 and Type 21 cable ties are classified in 6.2.1DV and6.2.2DV.1. In Mexico, Type 11 and Type 21 are not recognized classifications.3DV D1 Add the following terms to Clause 3:3DV.1 Air-handling spaces ducts or plenums used for environmental air and otherspaces used for environmental air, s

22、uch as above hung ceilings or below raised floors.This does not include plenums used for the removal of dust, loose stock, or vapour, orfor ventilation of commercial-type cooking equipment.3DV.2 Type test test conducted on sample representing production.4DV DC Add the following to Clause 4:4DV.1 In

23、Canada, general requirements are given in CAN/CSA-C22.2 No. 0.4DV.2 In Canada and the United States, an adhesive relied upon for securement of a fixingdevice shall be tested in accordance with the requirements in Annex DVA, Adhesives.5.2DV D2 Modify the NOTE as follows:Delete the last two sentences

24、of the Note in 5.2.5.2ADV D2 Add the following new paragraph:When the equilibrium moisture content for a material is determined through a methodagreed to by the manufacturer and the testing laboratory, the stabilization time in Table 1may be reduced under the following conditions:a) the products moi

25、sture content in the as-received condition and after eachappropriate conditioning is measured using a calibrated moisture analyzerdevice;b) the samples are subjected to exposure to a constant temperature notexceeding 50 2 C and relative humidity not exceeding 80 5 percent; andFEBRUARY 12, 2013 NATIO

26、NAL DIFFERENCES FOR UL UL 62275 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULc) the products equilibrium moisture content is verified using a calibratedmoisture analyzer device.5.7DV D1 Modify by adding the following text:In Mexico, an ove

27、n as specified in NMX-J-417-ANCE-2005 is considered equivalent.5.8DV D1 Add the following paragraphs to 5.8:5.8DV.1 A surface-mounted fixing device, the performance of which is dependent on themounting surface or the mounting orientation, shall comply with all applicable tests whenthe device is asse

28、mbled on the surfaces for which it is intended, and in each intendedmounting orientation declared by the manufacturer. If the manufacturer does not make adeclaration of mounting orientation or when it can be determined that a particularmounting orientation represents the most onerous condition, the

29、results of tests in thatorientation may represent all mounting orientations.5.8DV.2 A fixing device, the performance of which is dependent on the mounting hole size,the thickness of the material to which it is to be mounted, or the mounting orientation,shall comply with all applicable tests when the

30、 device is assembled to the minimum andmaximum thickness of each mounting surface and in each intended mounting orientationdeclared by the manufacturer. If the manufacturer does not make a declaration of mountingorientation or when it can be determined that a particular mounting orientation represen

31、tsthe most onerous condition, the results of tests in that orientation may represent allmounting orientations.5.9DV.1 D2 Replace the third paragraph with the following:If the cable tie is too short to meet the diameter of the smallest test mandrel, then a testmandrel having a diameter of 9.5 mm shal

32、l be used.5.9DV.2 DE Replace the fifth paragraph with the following:For the loop tensile strength tests, the mandrel shall be split in two equal parts and thecable ties positioned as shown in the top half of Figure 2DV.5.9DV.3 D1 Add the following paragraph after the fifth paragraph:Cable ties havin

33、g a low-profile locking device (head) with a parallel entry strap shall bemounted to the mandrel as shown in the lower half of Figure 2DV.5.9DV.4 D1 Add the following paragraph after the sixth paragraph:The use of separate steel or aluminum conditioning mandrels is permitted. Theconditioning mandrel

34、s need not be split but shall have a diameter approximatelyequivalent to the appropriate test mandrel, to allow the transfer of the sample to the testmandrel. Conditioned samples shall be carefully transferred to the appropriate testmandrel for carrying out the loop tensile strength test. Where it h

35、as been determined thatthe transfer of the samples from a conditioning mandrel to a test mandrel has influencedtest results, an additional sample set shall be conditioned and tested.FEBRUARY 12, 2013NATIONAL DIFFERENCES FOR UL UL 622756UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

36、ORDISTRIBUTION WITHOUT PERMISSION FROM ULFigure 2DV D1 Replace Figure 2 with the following:This is generated text for figtxt.FEBRUARY 12, 2013 NATIONAL DIFFERENCES FOR UL UL 62275 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULFEBRUARY 12, 2

37、013NATIONAL DIFFERENCES FOR UL UL 622758UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL6.2.1DV D1 Add the following to 6.2.1:Type 11 In Canada and the United States, the Type 11 classification refers to Type 1according to 6.2.1 with additiona

38、l pre-qualification to long-term performancecharacteristics of nonmetallic moulding materials according to CAN/CSA-C22.2 No. 0.17 orUL 746B. In Mexico, this classification does not apply.6.2.2DV D1 Add the following to 6.2.2:NOTE Cable ties classified according to 6.1.1 are considered only as Type 2

39、6.2.2DV.1 Type 21 In Canada and the United States, the Type 21 classification refers toType 2 according to 6.2.2 with additional pre-qualification to long-term performancecharacteristics of nonmetallic moulding materials according to CAN/CSA-C22.2 No. 0.17 orUL 746B. In Mexico, this classification

40、does not apply.6.3.1DV D1 Add the following to 6.3.1:6.3.1DV.1 Use of these ratings is recommended. Additional ratings between 50 C and 150C in 5-degree increments are also acceptable.6.3.1DV.2 Metallic cable ties constructed of aluminum shall be classified as 150 C andmetallic cable ties constructe

41、d of steel shall be classified as 300 C.6.3.3DV D2 Add the following to 6.3.3:6.3.3DV.1 This classification applies only when the temperature declared is lower than 0C.6.4.1DV D1 Delete 6.4.1:Clause 6.4.1 is not applicable.6.5.2.1DV D1 Delete 6.5.2.1:Subclause 6.5.2.1 is not applicable.6.6DV D1 Add

42、subclause 6.6DV According to smoke and heat generation:6.6DV.1 Not declared6.6DV.2 AH-1: Suitable for use in air-handling spaces 1 (plenums)For cable ties and fixing devices according to 6.1.1In Mexico, the classification AH-1 does not apply.6.6DV.3 AH-2: Suitable for use in air-handling spaces 2 (p

43、lenums)For cable ties and fixing devices according to 6.1.2 and 6.1.3In Mexico, the classification AH-2 does not apply.FEBRUARY 12, 2013 NATIONAL DIFFERENCES FOR UL UL 62275 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL7.1DV D1 Add the fol

44、lowing to 7.1:7.1DV.1 Markings shall be placed on the product, the smallest unit package in which theproduct is shipped, or installation instructions provided with the product.7.1DV.2 The following markings shall be provided on labels, packaging, or installationinstructions shipped with the product:

45、Fixing devices Cable ties onlyMax operating temp for application according to Table3Max operating temp for application according to Table3Min operating temp for application according to Table 4 Min operating temp for application according to Table 4Type designation Min installation temp if lower tha

46、n 0CMechanical strength as declared by the manufacturer Minimum and maximum bundle diameterLoop tensile strength according to Table 2Type designation7.1DV.3 In Canada and the United States, a fixing device that relies upon an adhesive forsecurement shall be marked to include the following:a) substra

47、tes accepted by investigation according to Annex DVA, Adhesives; andb) manufacturers recommendations for surface preparations, adhesiveapplication temperature range, application pressure and duration, and curing timeprior to loading.In Mexico, this requirement does not apply.7.3DV D1 Add the followi

48、ng to 7.3(a):7.3DV.1 In addition to the requirements in 7.3(a), the marking indicating the classification“Resistant to ultraviolet light” in accordance with 6.5.1.2 may be marked “For useoutdoors” or “For use outdoors or indoors” or with an equivalent wording.7.3DV.2 In Canada and the United States,

49、 the manufacturers declared minimum looptensile strength according to Table 2 may be supplemented with equivalent valuesexpressed in pounds-force (lb-f) or kilograms-force (kg-f). In Mexico, this does not apply.7.3DV.3 In Canada and the United States, a cable tie or fixing device classified as Type 2according to 6.2.2 or Type 21 according to 6.2.2DV.1 and also classified according to6.6DV.2 or 6.6DV.3 may be marked as follows:a) For products classified as 6.1.1 and 6.6DV.2, “Suitable for use in air-handlingspaces (plenums)” in ac