UL 62841-3-1 (ND)-2016 National Differences For Electric Motor-Operated Hand-Held Tools Transportable Tools And Lawn And Garden Machinery C Safety C Part 3-1 Particular Requirement .pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForElectric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-1: Particular Requirements For Transportable Table SawsUL COPYRIGH

2、TED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForElectric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-1: Particular Requirements For Transportable Table SawsFirst EditionEdition D

3、ate:Adoption Of The First Edition Of IEC 62841-3-1, Standard For Electric Motor-OperatedHand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part3-1: Particular Requirements For Transportable Table Saws, As The First Edition Of UL62841-3-1This standard is an adoption of IEC 6284

4、1-3-1, Edition 1, published by the IEC June 2014. Pleasenote that the National Difference document incorporates all of the U.S. national differences forUL 62841-3-1.This document provides a single listing of the National Differences included in the UL adoption ofthe corresponding IEC standard.All ri

5、ghts reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, eithe

6、r expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be liable for any special, incidental, consequential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages

7、arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof the possibility of such damage. In no event shall ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form of t

8、he claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonableattorneys fees) resulting from any error or deviation introduced while purchaser is sto

9、ring an electronicStandard on the purchasers computer system.Copyright 2016 Underwriters Laboratories Inc.AUGUST 29, 2016NATIONAL DIFFERENCES FOR2UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of

10、 the technical National Differences included in the UL adoptionof the corresponding IEC standard.In its IEC-based standards, UL uses the notations indicated below to identify national difference type, andthese types are additionally noted in this document. The standard may not use all types of these

11、deviations.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich would compromise safety for U.S. consumers and users of products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable,

12、 but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These are deviations based on the component standards and will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations

13、 based on editorial comments or corrections.DR - These are deviations based on the national regulatory requirements.Each national difference contains a description of what the national difference entails. Typically one of thefollowing words is used to explain how the text of the national difference

14、is to be applied to the base IECtext:Addition / Add - An addition entails adding a complete new numbered clause, subclause, table, figure,or annex. Addition is not meant to include adding select words to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered

15、 clause, subclause, table,figure, or annex without any replacement text.Modification / Modify - A modification is an altering of the existing base IEC text such as the addition,replacement or deletion of certain words or the replacement of an entire clause, subclause, table, figure,or annex of the b

16、ase IEC text.AUGUST 29, 2016 NATIONAL DIFFERENCES FOR 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences8.2DV D1 Modification: Add the following to Subclause 8.2 of the Part 1:The following statements shall be verbatim:a) DA

17、NGER Never place your hands in the vicinity or in line with the saw blade.b) WARNING Wear eye protection or the sign M004 of ISO 7010.c) WARNING Always use a properly functioning saw-blade guard, riving knifeand anti-kickback device for every operation for which it can be used, includingall through

18、sawing.d) WARNING Use a push-stick or push-block when required.e) WARNING Do not perform any operation freehand.f) WARNING Pay particular attention to instructions on reducing risk ofkickback. (or Know how to reduce risk of kickback.)g) WARNING Never reach around or over saw blade. (or Never reach i

19、n back ofor over saw blade.)h) WARNING Turn off tool and wait for saw blade to stop before movingworkpiece or changing settings.i) WARNING Never stand directly in line with the saw blade. Always positionyour body on the same side of the saw blade as the fence.AUGUST 29, 2016NATIONAL DIFFERENCES FOR4