UL 62841-3-13-2018 UL Standard for Safety Electric Motor-Operated Hand-Held Tools Transportable Tools And Lawn And Garden Machinery C Safety C Part 3-13 Particular Requirements for.pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 62841-3-13 Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills STANDARD FOR SAFETYUL

2、 COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Electric Motor-Operated Hand-Held Tools, Transportable Tools A

3、nd Lawn And Garden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills, UL 62841-3-13 First Edition, Dated May 4, 2018 Summary of Topics Adoption Of The First Edition Of IEC 62841-3-13, Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Ga

4、rden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills As The First Edition Of UL 62841-3-13 This standard is an adoption of IEC 62841-3-13, Edition 1, published by the IEC February 2017. Please note that the National Difference document incorporates all of the U.S. Nation

5、al Differences for UL 62841-3-13. The new requirements are substantially in accordance with Proposal(s) on this subject dated August 25, 2017 and February 9, 2018. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any mean

6、s, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event wil

7、l UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the pos

8、sibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense,

9、 liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. MAY 4, 2018 UL 62841-3-13 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCT

10、ION OR DISTRIBUTION WITHOUT PERMISSION FROM UL MAY 4, 2018 UL 62841-3-13 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CSA Group CAN/CSA-C22.2 No. 62841-3-13:18 First Edition (IEC 62841-3-13:2017, MOD) Underwriters

11、Laboratories Inc. UL 62841-3-13 First Edition Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-13: Particular Requirements For Transportable Drills May 4, 2018 This national standard is based on publication IEC 62841-3-13, First Edition (2017).

12、 ANSI/UL 62841-3-13-2018UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment for Amendments This standard is issued jointly by the Canadian Standards Association (operating as “CSA Group”) and Underwriters Laboratories Inc. (UL). Comme

13、nts or proposals for revisions on any part of the standard may be submitted to CSA Group or UL at any time. Revisions to this standard will be made only after processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will issue revisions to this standard by m

14、eans of a new edition or revised or additional pages bearing their date of issue. ISBN 978-1-4883-1562-6 2018 Canadian Standards Association All rights reserved. No part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subje

15、ct to review within ve years from the date of publication, and suggestions for its improvement will be referred to the appropriate committee. The technical content of IEC and ISO publications is kept under constant review by IEC and ISO. To submit a proposal for change, please send the following inf

16、ormation to inquirescsagroup.org and include Proposal for change in the subject line: Standard designation (number); relevant clause, table, and/or gure number; wording of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Groups On

17、line Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2018 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ownersh

18、ips, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the First Edition. The most recent designation of ANSI/UL 62841-3-13 as an American National Standard (ANSI) occurred on May 4, 2018. The ANSI approval for this

19、standard does not include the Cover Page, Transmittal Pages, Title Page, Preface Page, National Difference Page or IEC Foreword. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Col

20、laborative Standards Development System (CSDS) at https:/. To purchase UL Standards, visit ULs Standards Sales Site at http:/ HowToOrder.aspx or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .

21、 4 NATIONAL DIFFERENCES . 6 FOREWORD 7 1 Scope 10 2 Normative references .10 3 Terms and denitions 10 4 General requirements 11 5 General conditions for the tests 11 6 Radiation, toxicity and similar hazards 11 7 Classication 11 8 Marking and instructions 11 9 Protection against access to live parts

22、 13 10 Starting 13 11 Input and current .13 12 Heating 13 13 Resistance to heat and re 13 14 Moisture resistance .13 15 Resistance to rusting 13 16 Overload protection of transformers and associated circuits 13 17 Endurance .13 18 Abnormal operation .13 19 Mechanical hazards .14 20 Mechanical streng

23、th .16 21 Construction .16 22 Internal wiring 17 23 Components .17 24 Supply connection and external exible cords 17 25 Terminals for external conductors .17 26 Provision for earthing 17 27 Screws and connections .17 28 Creepage distances, clearances and distances through insulation 18 Annexes Annex

24、 I (informative) Measurement of noise and vibration emissions I.2 Noise test code (grade 2) 23 I.3 Vibration .23 Annex K (normative) Battery tools and battery packs Bibliography MAY 4, 2018 CAN/CSA-C22.2 NO. 62841-3-13:18 UL 62841-3-13 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION

25、 OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the harmonized CSA Group and UL Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills. It is the First edition of CAN/CSA-C

26、22.2 No. 62841-3-13 and the First edition of UL 62841-3-13. This harmonized standard is based on IEC Publication 62841-3-13: First edition Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills, is

27、sued February 2017. IEC 62841-3-13 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of standards for Hand-Held, Motor-Op

28、erated, and Transportable Tools and Lawn and Garden Machinery UL are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Elect

29、ric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Stan

30、dards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Application of Standard Where reference is

31、 made to a specic number of samples to be tested, the specied number is to be considered a minimum quantity. Note: Although the intended primary application of this standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its s

32、uitability for their particular purpose. CAN/CSA-C22.2 No. 62841-3-13 is to be used in conjunction with the First edition of CAN/CSA-C22.2 No. 62841-1. The requirements for transportable drills are contained in this Part 3 Standard and CAN/CSA-C22.2 No. 62841-1. Requirements of this Part 3 Standard,

33、 where stated, amend the requirements of CAN/CSA-C22.2 No. 62841-1. Where a particular subclause of CAN/CSA-C22.2 No. 62841-1 is not mentioned in CAN/CSA-C22.2 No. 62841-3-13, the CAN/CSA-C22.2 No. 62841-1 subclause applies. UL 62841-3-13 is to be used in conjunction with the First edition of UL 628

34、41-1. The requirements for transportable drills are contained in this Part 3 Standard and UL 62841-1. Requirements of this Part 3 Standard, where stated, amend the requirements of UL 62841-1. Where a particular subclause of UL 62841-1 is not mentioned in UL 62841-3-13, the UL 62841-1 subclause appli

35、es. MAY 4, 2018 CAN/CSA-C22.2 NO. 62841-3-13:18 UL 62841-3-13 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Level of harmonization This standard adopts the IEC text with national differences. This standard is published as an equivalent st

36、andard for CSA Group and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for codes and governmental regulations as well as those recognized as being in accordance with NAFTA Article 905, for e

37、xample, because of fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country considers appropriate. Presentation is word for word except for editorial changes. All national differences from the IEC text are includ

38、ed in the CSA Group and UL versions of the standard. While the technical content is the same in each organizations version, the format and presentation may differ. Reasons for Differences From IEC National differences from the IEC are being added in order to address safety and regulatory situations

39、present in the US and Canada. Interpretations The interpretation by the standards development organization of an identical or equivalent standard is based on the literal text to determine compliance with the standard in accordance with the procedural rules of the standards development organization.

40、If more than one interpretation of the literal text has been identied, a revision is to be proposed as soon as possible to each of the standards development organizations to more accurately reect the intent. IEC Copyright For CSA Group, the text, gures, and tables of International Electrotechnical C

41、ommission Publication IEC 62841-3-13 Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills, copyright 2017, are used in this standard with the consent of the International Electrotechnical Commiss

42、ion. The IEC Foreword is not a part of the requirements of this standard but is included for information purposes only. These materials are subject to copyright claims of IEC and UL. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prio

43、r written permission of UL. All requests pertaining to the Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills Standard should be submitted to UL. MAY 4, 2018 CAN/CSA-C22.2 NO. 62841-3-13:18 UL

44、62841-3-13 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL NATIONAL DIFFERENCES National Differences from the text of International Electrotechnical Commission (IEC) Publication 62841-3-13, Electric Motor-Operated Hand-Held Tools, Transport

45、able Tools and Lawn and Garden Machinery Safety Part 3-13: Particular Requirements for Transportable Drills, copyright 2017, are indicated by notations (differences) and are presented in bold text. The national difference type is included in the body. There are ve types of National Differences as no

46、ted below. The difference type is noted on the rst line of the National Difference in the standard. The standard may not include all types of these National Differences. DR These are National Differences based on the national regulatory requirements. D1 These are National Differences which are based

47、 on basic safety principles and requirements, elimination of which would compromise safety for consumers and users of products. D2 These are National Differences from IEC requirements based on existing safety practices. These requirements reect national safety practices, where empirical substantiati

48、on (for the IEC or national requirement) is not available or the text has not been included in the IEC standard. DC These are National Differences based on the component standards and will not be deleted until a particular component standard is harmonized with the IEC component standard. DE These ar

49、e National Differences based on editorial comments or corrections. Each national difference contains a description of what the national difference entails. Typically one of the following words is used to explain how the text of the national difference is to be applied to the base IEC text: Addition / Add - An addition entails adding a complete new numbered clause, subclause, table, gure, or annex. Addition is not meant to include adding select w