1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOctober 9, 20061SUBJECT 1029AOUTLINE OF INVESTIGATIONFORIGNITORS AND RELATED AUXILIARIES FOR HID LAMP BALLASTSIssue Number: 1OCTOBER 9, 2006Summary of TopicsThis is the first issue of the Outline
2、 of Investigation for Ignitors andRelated Auxiliaries for HID Lamp Ballasts.The UL Foreword is no longer located within the UL Outline of Investigation. Forinformation concerning the use and application of the requirements contained inthis Outline of Investigation, the current version of the UL Fore
3、word is located onULStandardsInfoNet at: http:/ 2006 UNDERWRITERS LABORATORIES INC.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULOCTOBER 9, 2006SUBJECT 1029A2No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION
4、 ORDISTRIBUTION WITHOUT PERMISSION FROM ULCONTENTSINTRODUCTION1 Scope .52 General 52.1 Components .52.2 Units of measurement .62.3 Reference publications 63 Glossary .7CONSTRUCTION4 Construction 84.1 Types of devices .84.2 Enclosure .94.3 Resistance to corrosion 124.4 Means for mounting .134.5 Compo
5、und (potting) 134.6 Installation supply and load connections (terminals) 144.7 Wire .174.8 Grounding 184.9 Electrical parts 204.10 Electrical insulation .204.11 Clearances and creepage distances 214.12 Polymeric materials .254.13 Printed wiring boards .284.14 Power capacitors .284.15 Thermal protect
6、ion .304.16 Over-current protection 31PERFORMANCE5 Tests .325.1 General notes on tests and sample requirements .325.2 Normal operation 345.3 Abnormal operation 385.4 Mechanical tests 396 Instrumentation and Test Apparatus 446.1 General notes on tests and sample requirements .446.2 Output measurement
7、s .456.3 Temperature test 456.4 Dielectric voltage withstand test .466.5 Lamp abnormal conditions 466.6 Component abnormal conditions 466.7 Recessed use abnormal 466.8 Enclosure impact 466.9 Strain relief test .466.10 Pullout, bending, and torque tests 476.11 Water spray test .476.12 Method of measu
8、rement for terminal compartment volume 477 Manufacturing and Production Tests .47OCTOBER 9, 2006 SUBJECT 1029A 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL7.1 Production-line dielectric voltage-withstand test .47MARKING8 General .49APPEND
9、IX AStandards for ComponentsA1UL Standards .A1OCTOBER 9, 2006SUBJECT 1029A4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULINTRODUCTION1 Scope1.1 These requirements address the construction requirements and tests for ignitors for high intensit
10、ydischarge (HID) lamps that require an external starting pulse or pulses. These requirements are forignitors that could be mounted outside of or remote from a luminaire as well as ignitors that must beinstalled within the electrical enclosure of a luminaire or sign.1.2 These requirements include 2,
11、3, and 4 wire ignitors for use with high-pressure sodium and metalhalide lamps, as well as ignitors known as hot re-strike type.1.3 These requirements also cover certain auxiliaries for HID lamps and ballasts: two level dimming (bycapacitors), time-out circuits, and controls for auxiliary tungsten l
12、amps.1.4 These requirements do not cover ballasts that connect with the devices covered by this outline.2 General2.1 Components2.1.1 Except as indicated in 2.1.2, a component of a product covered by this outline shall comply with therequirements for that component. See Appendix A for a list of stand
13、ards covering components used in theproducts covered by this outline.2.1.2 A component is not required to comply with a specific requirement that:a) Involves a feature or characteristic not required in the application of the component in theproduct covered by this outline, orb) Is superseded by a re
14、quirement in this outline.2.1.3 A component shall be used in accordance with its rating established for the intended conditions ofuse.2.1.4 Specific components are incomplete in construction features or restricted in performancecapabilities. Such components are intended for use only under limited co
15、nditions, such as certaintemperatures not exceeding specified limits, and shall be used only under those specific conditions.OCTOBER 9, 2006 SUBJECT 1029A 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL2.2 Units of measurement2.2.1 Except fo
16、r conductor size, values stated without parentheses are the requirement. Values inparentheses are explanatory or approximate information.2.2.2 All values of voltage and current are true root mean square (rms) values unless otherwise indicated.2.2.3 For customary purposes wire sizes are in American W
17、ire Gauge (AWG).2.3 Reference publications2.3.1 Any undated reference to a code or standard appearing in the requirements of this outline ofinvestigation shall be interpreted as referring to the latest edition of the code or standard.ASTM (American Society for Testing Materials)ASTM 653Standard Spec
18、ification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated(Galvannealed) by the Hot-Dip ProcessNFPA (National Fire Protection Association)NFPA 70National Electrical CodeIEC (International Electrotechnical Commission)IEC 61347-1Lamp controlgear Part 1: General and safety requiremen
19、tsISA (The Instrumentation, Systems, and Automation Society)ISA MC 96.1Temperature Measurement ThermocouplesUL StandardsUL 1029Standard for High-Intensity-Discharge Lamp BallastsOCTOBER 9, 2006SUBJECT 1029A6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMIS
20、SION FROM UL3 Glossary3.1 For the purpose of this outline the following definitions apply:3.2 DEVICE A term, when used, refers to all devices covered by this outline. Requirements pertainingto specific devices are so noted.3.3 DEVICE, BUILT-IN A device specifically designed to be contained within a
21、luminaire or theelectrical enclosure of a sign. A device with lead wires or terminals that are not enclosed would beconsidered a built-in device.3.4 DEVICE, INDEPENDENT A device that has its own enclosure and can be mounted separately orattached to the outside of a luminaire or sign without any addi
22、tional enclosure. This may consist of abuilt-in device housed in a suitable enclosure which provides all the necessary protection according toits rating. A device not identified as an independent device would be considered, by default, to be built-in.3.5 IGNITOR A device intended to generate voltage
23、 pulses to start discharge lamps and which doesnot provide for the preheating of electrodes.3.6 LOCATION, DRY A location not normally subject to dampness or wetness. A location classifiedas dry may be temporarily subject to dampness, for example, a building under construction.3.7 LOCATION, DAMP A lo
24、cation protected from weather and not subject to direct exposure orsaturation by water but subject to moderated degrees of moisture, for example, the inside of a sign orluminaire intended for wet locations.3.8 LOCATION, OUTDOOR See definition of damp location above.3.9 POWER CAPACITOR A capacitor th
25、at is connected:a) in series with a lamp or lamps and provides the device impedance for the lamp current; orb) across the input of the device or across an extension of the primary winding for power-factorcorrection.3.10 PEAK VOLTAGE Highest value of the voltage pulses generated by an ignitor at the
26、output.3.11 RATED MAXIMUM TEMPERATURE, tc The highest permissible temperature that may occur onthe outer surface (at the indicated place, if marked) under normal operating conditions and at the ratedvoltage or the maximum of the rated voltage range. The value of tcwould be determined by themanufactu
27、rer.3.12 WEATHERPROOF A device constructed so as to be suitable for direct exposure to the weather.Various weather conditions of rain, dust, and temperature extremes do not result in a hazard.OCTOBER 9, 2006 SUBJECT 1029A 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTIO
28、N WITHOUT PERMISSION FROM ULCONSTRUCTION4 Construction4.1 Types of devices4.1.1 For guidance in the use of this section, the intended usage, either an independent device or built-indevice, would first be determined. Additional requirements are described throughout this outline.4.1.2 Examples of an i
29、ndependent device would be:a) A device that can be mounted remote from a luminaire or a sign.b) A device with lead wires or terminals on the side intended for mounting and could beattached to, but outside of the electrical enclosure of a luminaire.4.1.3 Examples of a built-in device would be:a) A de
30、vice with unenclosed lead wires or terminals.b) A device with an incomplete enclosure.4.1.4 Devices are categorized according to the use for which they are intended. A device in one categoryis acceptable, with respect to protection against corrosion, is also acceptable in the category thatprecedes i
31、t in the following list:a) A device only intended for use an indoor, dry location.b) A Damp (Outdoor) Type 1 or Type 2 device is acceptable for use in:1) Outdoor equipment;2) A luminaire intended for use in wet or damp locations; or3) An outdoor sign.c) A weatherproof device is intended for exposure
32、 to the weather without an additionalenclosure.OCTOBER 9, 2006SUBJECT 1029A8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4.2 Enclosure4.2.1 A device enclosure shall have the strength and rigidity required to resist the abuses to which it is
33、liable to be subjected, without increasing the risk of electric shock or fire due to a reduction of the requiredspacing to live parts or the loosening or displacement of live parts. The acceptability of the enclosure isfurther determined by intended usage of the device and factors such as the enclos
34、ure material, theenclosure material thickness, and the openings in the enclosure.4.2.2 A device shall be provided with an enclosure of metal or of a polymeric material that has beeninvestigated and found to be evaluated for the intended use. See 4.12 for requirements for a polymericmaterial used as
35、an enclosure.4.2.3 The thickness of a cast- or sheet-metal enclosure shall be in accordance with Table 4.1.Table 4.1Enclosure thicknessMetal Independent5kg(11lbs) Built-inmm (inch)Die-cast metal 1.2 (3/64)Other cast metal 1.6 (1/16)Weatherproof ratedSheet steel, galvanized 1.40 (0.056)Sheet steel, u
36、ncoated 1.35 (0.053)Sheet metal, non-ferrous 0.80 (0.032)Other than weatherproofSheet steel, galvanized 0.75 (0.029) 0.75 (0.029)Sheet steel, uncoated 0.65 (0.026) 0.65 (0.026)Sheet steel uncoated or metal nonferrous, potted assembly 0.50 (0.020) 0.50 (0.020)Sheet steel uncoated or metal nonferrous,
37、 and with insulatedliner surrounding printed circuit board0.40 (0.016)Sheet metal, nonferrous, including extruded 0.80 (0.032) 0.80 (0.032)Notes: 1) These are minimum dimensions based on nominal metal gauge thicknesses, for example 22 Manufacturers SheetGauge, is 0.033 in., nominal, 0.026 in. minimu
38、m. Because of the tolerance in metal gauge sizes it may be necessary toincrease the metal thickness so it is never less than the specified minimum.2) Metal is described as uncoated, however when measured, it will have an additional metallic or organic coating when thecontrol device is marked “Damp (
39、Outdoor) Type 1.”4.2.4 The enclosure for an independent device is able to have:a) Seams overlapped, except that a total length of not more than 75 mm (3 in) of butt seammeets the intent of this requirement when no opening in such seam is more than 3.2 mm2(0.005 in2) in area and the total area of suc
40、h openings is no more than 1.6 cm2(0.250 in2). andb) Openings for lead wires, the perimeter of which shall fit closely around the wire it encircles.An opening of 3.2 mm (1/8 inch) diameter or less complies with this requirement.OCTOBER 9, 2006 SUBJECT 1029A 9UL COPYRIGHTED MATERIAL NOT AUTHORIZED FO
41、R FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4.2.5 The enclosure for a device for dry or damp (outdoor) locations is able to have openings forventilation when:a) It is intended for built-in applications.b) Circular openings have a diameter not exceeding 3 mm (0.12 in) and minimum
42、spacingbetween circular openings is 3 mm (0.12 in).c) Rectangular (or square) openings have dimensions not exceeding 3 mm (0.12 in) across and30 mm (1.18 in) in length.d) The pattern of openings for metal enclosures is such that the through air clearance betweenlive parts and the dead metal enclosur
43、e is not reduced below the values specified in 4.11, whenthe enclosure is subjected to the Rod Pressure Loading Test in the Standard for Fluorescent-Lamp Ballasts, UL 935.e) The openings in (b) and (c) do not allow accessibility to shock hazardous parts by use of thearticulated probe shown in Figure
44、 4.1.f) The device is marked in accordance with 8.15.This is generated text for figtxt.OCTOBER 9, 2006SUBJECT 1029A10UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULFigure 4.1Articulated probeMaterial: Metal pointed end to first knuckle.Tolera
45、nces: 0.2 mm except gaps between knuckles.OCTOBER 9, 2006 SUBJECT 1029A 11UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4.3 Resistance to corrosion4.3.1 Enclosures or other parts constructed of aluminum are considered acceptably protected ag
46、ainstcorrosion for dry and damp (outdoor) location ratings. Enclosures or other parts constructed of iron orsteel shall be suitably protected from rusting by painting, plating, or an equivalent. Both inside and outsidesurfaces of an enclosure shall be protected. A protective coating need not be appl
47、ied to:a) The interior of a device enclosure that is completely filled with potting compound; orb) Flat metal surfaces that are tightly clamped together.4.3.2 A device marked with a Damp (Outdoor) Type 1 rating shall comply with 4.3.1 and 4.3.3, and havelead wire insulation that complies with 4.7.10
48、.4.3.3 A device marked with a Damp (Outdoor) Type 1 rating, and incorporating pre-painted steel orsteel with a metallic ASTM coating designated G60 or G90 is permitted to have untreated sheared edgesor punched holes.4.3.4 A ferrous metal enclosure of a device marked with a Damp (Outdoor) Type 2 rati
49、ng shall be pottedor compound filled and protected against corrosion as specified in Table 4.2. In lieu of corrosionresistance the metallic coatings specified in Table 4.2, a steel enclosure provided with an organic coatingcomplies with this requirement if comparative tests with galvanized-sheet steel (without annealing, wiping,or other surface treatment) conforming to ASTM coating designation G60 indicate the coating providesequivalent protection. Among the factors that are to be taken in
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1