UL SUBJECT 1365-2018 UL Outline for Investigation Corrugated Medical Tubing (CMT) Systems (Issue 5).pdf

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJANUARY 29, 20181UL 1365Outline of Investigation for Corrugated Medical Tubing (CMT) SystemsIssue Number: 3January 29, 2018Summary of TopicsThis third issue of the Outline of Investigation for Co

2、rrugated MedicalTubing (CMT) Systems, UL 1365, which covers corrugated medical tubingsystems intended for use in hospitals and health centers for distributionof nonflammable medical gas, is being issued to address correctionsto Section 18, Mechanical Tube Fitting Performance.ULs Outlines of Investig

3、ation are copyrighted by UL LLC. Neither a printed norelectronic copy of an Outline of Investigation should be altered in any way. All ofULs Outlines of Investigation and all copyrights, ownerships, and rights regardingthose Outlines of Investigation shall remain the sole and exclusive property of U

4、LLLC.COPYRIGHT 2018 UL LLCUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULJANUARY 29, 2018UL 13652No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULCONTENTSINTRODUCTION

5、1 Scope .42 Units of Measurement .43 Undated References 44 Components 4CONSTRUCTION5 General 5PERFORMANCE6 General 57 External Leakage Test .68 Hydrostatic-Strength Test 69 Impact Test 610 Axial Tension Test .711 Torsion Test .712 Temperature Test 713 Flame Test 814 Compression Test .915 Bending Tes

6、t 916 Electrical Resistance Test .917 Jacket Burning Characteristics .1118 Mechanical Tube Fitting Performance .1119 System Piping Purge Test .1220 System Piping Purity Test .12MARKINGS21 General 14INSTRUCTIONS22 General 1423 Installation and Operating Instructions .15JANUARY 29, 2018 UL 1365 3UL CO

7、PYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULINTRODUCTION1 Scope1.1 This outline covers corrugated medical tubing systems intended for use in hospitals and healthcenters for distribution of nonflammable medical gas in accordance with the Standar

8、d for Health CareFacilities, NFPA 99.1.2 CMT systems are intended for inside aboveground and in slab, when installed in approvednonmetallic conduit, applications only.1.3 This outline covers medical tubing systems up to 2 inches (50.8 mm), based on the nominal insidediameter of the tubing.1.4 These

9、products have not been evaluated for use after fires, natural disasters such as earthquakes, orexcessive physical damage beyond the expected assembly, installation and uses as identified in theserequirements.1.5 These products are intended to be periodically inspected and maintained for continued se

10、rvice, ortaken out of service if necessary by qualified persons in accordance with industry recommended practicesand/or the manufacturers instructions.2 Units of Measurement2.1 Values stated without parentheses are the requirement. Values in parentheses are explanatory orapproximate information.3 Un

11、dated References3.1 Any undated reference to a code or standard appearing in the requirements of this outline shall beinterpreted as referring to the latest edition of that code or standard.4 Components4.1 Except as indicated in 4.2, a component of a product covered by this standard shall comply wit

12、h therequirements for that component.4.2 A component is not required to comply with a specific requirement that:a) Involves a feature or characteristic not required in the application of the component in theproduct covered by this outline, orb) Is superseded by a requirement in this outline.4.3 A co

13、mponent shall be used in accordance with its rating established for the intended conditions ofuse.JANUARY 29, 2018UL 13654UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL4.4 Specific components are incomplete in construction features or restri

14、cted in performance capabilities.Such components are intended for use only under limited conditions, such as certain temperatures notexceeding specified limits, and shall be used only under those specific conditions.CONSTRUCTION5 General5.1 A product shall employ materials found by investigation and

15、 allowed by NFPA 99 to be acceptable forthe intended application.5.2 Corrugated medical tubing systems shall be constructed entirely of new and unused parts andmaterials.5.3 A product shall be assembled so that it will not be adversely affected by the vibration of normaloperation.PERFORMANCE6 Genera

16、l6.1 Representative samples of each size and specific construction of the CMT are to be subjected to thetests described in these requirements.6.2 CMT systems are to be tested on the following basis consistent with the intended use of the productand Table 6.1:a) Size or diameter;b) Minimum radius of

17、bend (per manufacturers instructions); andc) Maximum rated pressure (per manufacturers instructions).Table 6.1CMT systemSize (in.)OAL (in.) hydrostatic,vibration, torsion tests Length over diameter ratio Torsional stress (in-lb)3/8 17 37 1501/2 21 34 15034 26 28 2001 26 26 2501-12 36 24 3502 45 23 4

18、506.3 For tests requiring pressure a calibrated pressure-indicating device is to be mounted to indicatepressures developed within the vessel. The pressure-indicating device shall comply with one of thefollowing:a) An analog gauge having a pressure range of at least 150 percent of the anticipatedmaxi

19、mum working pressure;JANUARY 29, 2018 UL 1365 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULb) A digital pressure transducer, or other digital gauge, that is calibrated over a range ofpressure that includes the test pressure; orc) Other dev

20、ice that is equivalent to the devices in (a) or (b).7 External Leakage Test7.1 A CMT system shall not leak when tested as described below.7.2 One sample of each diameter, not less than 3 feet (914 m) in length, shall be installed with one endconnected to an air supply source and the other end plugge

21、d. The pressure is slowly increased to 1-1/2times rated pressure and maintained at that pressure for at least 1 minute.8 Hydrostatic-Strength Test8.1 A medical tubing system shall not leak nor rupture when tested as described below.8.2 One sample of each diameter per Table 6.1 having a minimum lengt

22、h of 24 inches (610 mm) shall beused in this test. The sample is to be installed in a straight line, with one end attached to the pressuresource and other end plugged and free. Each sample is to be filled with water so as to exclude all air.8.3 The pressure is to be uniformly raised to 1-1/2 times r

23、ated pressure and maintained at that pressurefor at least 1 minute. The tubing is then to be bent with a radius of curvature as specified in Table 6.1 andthe pressure maintained for one additional minute.8.4 With the tubing maintained in the bent position, the pressure is then to be increased to 3.5

24、 timesmaximum rated at least pressure for 1 minute.9 Impact Test9.1 The medical tubing system shall withstand an impact of 30 ft-lb (40.67 Nm), using a 10 lb.(4.54 kg)weight falling 3 ft. (0.914 m) through a vertical guide tube, without external leakage, per Section 7, beforeand after having been te

25、sted as described below. The striking nose of the falling weight shall have a 0.5in (12.7 mm) spherical radius and shall be made of steel.9.2 A tubing assembly consisting of each type of fitting and 2 ft. (610 mm) long sections of each type sizeshall be assembled in accordance with the manufacturers

26、 installation instructions.9.3 A V-block steel holder shall be used to support the tubing for impacting. The sides of the “V” shall beof sufficient length to support the tubing below the top edges of the “V.” The V-block and the samples tobe impacted shall be supported on a hard flat surface.9.4 A t

27、otal of 5 specimens of the tubing shall be impacted, with each specimen being impacted once. Thearrangement shall be such that the striking nose of the falling weight will impact at the center of thespecimen.JANUARY 29, 2018UL 13656UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDI

28、STRIBUTION WITHOUT PERMISSION FROM UL9.5 A total of five specimens of each type of fitting shall be impacted, with each specimen being impactedonce. The arrangement shall be such that the striking nose of the falling weight will impact at thecenterline of contact between the striking weight and the

29、longitudinal center of the fitting.10 Axial Tension Test10.1 The CMT system shall withstand the tension without external leakage, per Section 7, before andafter having been tested as described below.10.2 Test samples consisting of each size of piping and each type of fitting on each end shall beasse

30、mbled in accordance with the manufacturers installation instructions. The sample length shall bebased on a minimum length over internal diameter ratio (L/D) of 6, but shall be at least 6 in (152 mm) long.10.3 One end of the assembly shall be securely attached to a fixed hose to which a hydrostatic s

31、upplysystem and pressure gage was connected. The assembly shall be pressurized to its maximum operatingpressure. The other end was securely attached in a similar manner to a closed hose connected to amechanical means capable of applying a constant pulling force of 800 lb/in2of nominal inside tubedia

32、meter.10.4 The required tensile load shall be applied at a rate smooth and continuous, and then maintained forat least 5 minutes. The tubing assembly is removed from the test apparatus and the external leakage testshall be repeated.11 Torsion Test11.1 The system shall withstand the maximum torsion s

33、tresses specified in Table 6.1. The ExternalLeakage Test, Section 7, shall be conducted before and after having been tested as described below.11.2 One sample not less than 24 inches (610 mm) in length of each tube was tested. One end was firmlysecured and the other end was anchored in a straight li

34、ne such that it could be rotated. A torsional stressshall be gradually increased until the stress indicated in table 1 shall be applied to the rotatable end.11.3 The stress shall be then removed and the sample shall be subjected to the external leakage test.12 Temperature Test12.1 The CMT fitting sh

35、all withstand a temperature of 1000 F (538 C) for 30 minutes, without leaking inexcess of 6.0 ft3of air per hour. The External Leakage Test, Section 7, shall be conducted before asdescribed below.12.2 An assembly with one of each type of fitting shall be assembled in accordance with themanufacturers

36、 installation instructions. The outlet of the assembly is sealed and the inlet is connected toa system capable of supplying clean dry air at the specified test pressure, and to a flow-measuring devicecapable of accurately indicating the allowable leakage rate. The flow-measuring device is located be

37、tweenthe air supply and the inlet of the piping assembly. A thermocouple shall be firmly attached to one fittingto monitor its temperature.JANUARY 29, 2018 UL 1365 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL12.3 The assembly shall be pla

38、ced in a preheated 1000 F (538 C) test oven. The sample shall bearranged so that the inlet of the piping assembly extends through an opening in the oven wall andconnects to the air supply system.12.4 Air is admitted to the system and maintained at a minimum pressure of 55 psi (379 kPa) throughoutthe

39、 test, unless a leak is indicated by a drop in pressure. In this event the test shall be discontinued.12.5 When the temperature of the fitting reaches 990 F (532 C), the oven shall be adjusted asnecessary so that the fitting temperature is maintained at 990 F to 1010 F (532 C to 543 C) for at least1

40、 hour. During this period, any leakage indicated by the flow-meter shall not exceed 6.0 ft3per hour whencorrected to standard conditions of 30 in Hg (101.59 kPa) column pressure and 60 F (15.5 C).13 Flame Test13.1 The medical tubing system, without jacket, shall not leak or show evidence of damage a

41、fter beingsubjected to the flame test as described below. The External Leakage Test, Section 7, shall be conductedbefore and after having been tested.13.2 One sample of each diameter and at least 12 inches (305 mm) long between couplings is to be usedin this test. A lineal section of 6 inches (152 m

42、m) is to be suspended horizontally at a vertical distance of3 inches (76.2 mm) above and parallel to a strip pipe gas burner.13.3 The burner is to be constructed of 3/4 inch Schedule 40 iron pipe (Standard for Welded andSeamless Wrought Steel Pipe, ANSI/ASME B36.10M) having a straight line of 1/16 i

43、nch (1.6 mm) drilledports, on 1/2 inch (12.7 mm) centers, located along the top for a distance of 8 inches (203 mm). A gaspressure equal to 1 inch (25.4 mm) water column is to be maintained in the pipe when gas equivalent tonatural gas having approximately 1000 Btu per cubic foot (37.3 MJ/m3) is emp

44、loyed.13.4 The flame resulting from this apparatus is to burn under at least 6 inches (152 mm) of the exposedlength of tube and under one coupling or union at one end. The sample is to be exposed to the flame for5 minutes.13.5 At the end of the flame exposure, the sample is to be cooled to room temp

45、erature and is then to besubjected to the external leakage test.JANUARY 29, 2018UL 13658UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL14 Compression Test14.1 The medical tubing system shall withstand the effects of an external load of 1000 p

46、ounds (454 kg)applied over a distance of 1 inch (25.4 mm) along the length of the pipe at three equally spaced locationsand not leak when subjected to a pressure 3.5 times the maximum operating pressure.14.2 One 18 inch (45.7 cm) sample of each diameter shall be tested. A hydrostatic pressure of 25

47、psig(172.4 kPa) shall be maintained within the sample when under test.14.3 With the sample supported uniformly along its length, a load of 1000 pounds (454 kg) shall besuccessively applied by a flat metal surface over a distance of 1 inch (25.4 mm) along the length of thetube at three equally spaced

48、 locations.14.4 The load at each location shall be maintained for at least 1 minute.14.5 After the loads are completed the sample shall be subjected to a hydrostatic pressure of 3.5 timesmaximum rated pressure for at least 1 minute.15 Bending Test15.1 The medical tubing system shall withstand the ef

49、fects of repeated cycles of abnormal bending. TheExternal Leakage Test, Section 7, shall be conducted before and after having been tested15.2 One sample of each diameter having a length based on a minimum length over internal diameterratio (L/D) of 24, but shall be at least 2 ft (610 mm) long shall be supported uniformly along its length ason a table.15.3 The sample shall be successively bent to a 90 degree arc having a radius of 60 and 30 percent ofthe minimum radius per manufactures installation instructions. The bending at each of the two radii shallbe repeat