VA 08 34 53-2009 SECURITY DOORS AND FRAMES.pdf

1、12-09 08 34 53 - 1 SECTION 08 34 53 SECURITY DOORS AND FRAMES SPEC WRITER NOTE: Delete between /-/ if not applicable to project. Also delete any other item or paragraph not applicable in the section and insert additional items required by project and renumber paragraphs. Identify all frames by types

2、. Verify that drawings show the required doors and frames. See VA Physical Security Design Guide for security requirements Obtain blast resistance requirements from Physical Security Design Standards Definitions, a separate publication provided by the VA. PART I - GENERAL 1.1 DESCRIPTION A. The exte

3、nt of forced-entry resistant (FE) and ballistic resistant (BR) door assemblies required for the Project is indicated on Contract Drawings, and in Door/Frame/Hardware schedules, including construction, profiles, swing, sizes, hardware, accessories, devices, and locations. 1.2 RELATED WORK A. Refer to

4、 Division 3, CONCRETE. B. Refer to Division 4, MASONRY. C. Refer to Division 5, METALS for steel supports. D. Doors and frames not designated for special security performances: / Section 08 11 13, HOLLOW METAL DOORS AND FRAMES / / Section 08 14 00, WOOD DOORS /. E. Windows and frames of a forced ent

5、ry/ballistic resistant rated: Section 08 56 53, SECURITY WINDOWS F. Door Hardware: Section 08 71 00, DOOR HARDWARE. G. Glazing and ballistic rated glazing: Section 08 80 00, GLAZING. H. Package transfer boxes: Section 11 17 36, PACKAGE TRANSFER UNITS. I. Deal trays of a Forced Entry/Ballistic Resist

6、ant rating: Section 08 56, 59, SERVICE AND TELLER WINDOW UNITS. J. Guard Booths: Section 13 34 19, METAL BUILDING SYSTEMS. K. Card readers and biometric devices: Section 28 13 11, PHYSICAL ACCESS CONTROL SYSTEMS Provided by IHSNot for ResaleNo reproduction or networking permitted without license fro

7、m IHS-,-,-12-09 08 34 53 - 2 L. Intrusion alarm: Section 28 16 11, INTRUSION DETECTION SYSTEM 1.3 PERFORMANCE REQUIREMENTS A. General: Fabricate and install FE/BR door assemblies to achieve indicated levels of resistance. Extend resistance to include anchorages, interfaces with adjoining substrates,

8、 and hardware. Security attacks shall be unable to penetrate through closed/locked security door assemblies in manner described; it is recognized that such attacks may damage units beyond repair and reuse, requiring replacement of work by Government: 1. Fire-rated assemblies: Where indicated for fir

9、e resistance, provide flush steel doors-and-frame units; comply with NFPA 80, Standard for Fire Doors and Windows. Provide units that have been tested by recognized testing agency in accordance with NFPA No. 252 and ASTM E2074: 2. Forced-Entry (FE) resistant assemblies: Where door assembly is shown

10、or scheduled as FE, provide door manufacturers material and fabrication for panels, inserts, hardware, devices, and framing of units. Provide rated units where shown or scheduled: /a. No FE resistance rating. / /b. Provide resistance of 5 minutes for forced entry, using basic hand tools. / /c. Provi

11、de resistance of 15 minutes for forced entry, using basic hand tools. / 3. Ballistic Resistant (BR) assemblies: Where door assembly is shown or scheduled as BR, provide door manufacturers materials and fabrication for panel, inserts, and framing of unit. Provide rated units where shown or scheduled.

12、 /No BR resistance rating: / /a. UL 752 Level 3. / 1.4 SUBMITTALS A. General: For each security door assembly, submit the following in accordance with Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA AND SAMPLES. 1. Product data for each element of work, whether purchased from other manufacturers or pr

13、ovided as door Fabricators standard production. Include data substantiating that products comply with requirements of these specifications. 2. Manufacturers standard color chart. 3. Certificates: Letter from manufacturer indicating the products have been certified to meet the specified ratings. Prov

14、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-09 08 34 53 - 3 4. Shop drawings showing each dimensioned details of each door assembly, including performance rating, swing, hardware set, and adjacent construction. Provide drawings on B-size 11 in x 1

15、7 inch (300 mm x 430 mm) sheets. Show typical door exterior elevations at not less than inch = 1 foot (1:50) scale. After final modifications and corrections have been incorporated into the drawings, submit drawings as AutoCAD files with DWG extension. Show the following: a. Unit information: 1) Mod

16、el Number. 2) Ballistic resistant rating. 3) Marks (window no.). 4) Door/frame finish. 5) Door type. b. Elevation Drawings: 1) Rough opening. 2) Door opening. 3) Frame opening. 4) Vision opening. 5) Finished floor. 6) Sill condition. 7) Undercut for carpet. 8) Weather-stripping. 9) Reference numbers

17、 for primer and finish paint, including number of coats applies. 10) Door class rating: rated or non-rated. 11) Door and frame gauge thickness. c. Plan drawings: 1) Relate to elevation on drawing. 2) Identify “Attack” and “Protected” sides. 3) Identify door swing (i.e., RH, LH, RHRB, LHRB). 4) Provi

18、de key on drawings. 5) Indicate room space numbers taken from Contract Drawings. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-09 08 34 53 - 4 d. Details: Show section at not less than inch = 1 ft (1:20) scale of members indicating construction,

19、 size, and thickness of components, frame profile, location of conduit entry, threshold configuration, vision panel together with connections, fastenings, and means of separating dissimilar metals. e. Breakdown of Product Line Items: 1) If Manufacturer produces one contract line item as several part

20、s (door with transom and sidelights), they shall breakout items on drawings. Each item shall be a subdivision of that product line item number. 2) Installation instructions shall cite all anchorage components, including complete description of expansion anchor as well as installation criteria such a

21、s torque requirements, minimum embedment, and minimum edge distance, and shall include alert to installers to avoid cutting of rebar during concrete anchor installation. 1.5 QUALITY ASSURANCE A. Testing Laboratory Qualifications: For compliance with non-security performance requirements (such as fir

22、e ratings, resistance to deterioration from moisture, accessibility to persons with disabilities, or sound attenuation) on security door assemblies of this Section, use only those testing laboratories which have successfully demonstrated to Project Manager that they have experience and capabilities

23、needed to satisfactorily conduct required tests. B. Provide products that have been certified by Bureau of Diplomatic Security (DS) in accordance with DS/PSD SD-STD-01.01. 1.6 IDENTIFICATION SYSTEMS A. Identify each assembly to provide VA with ready reference to original manufacturer to facilitate r

24、eorders, replacement parts, service, resolution of complaints, and inventory. The label shall be typically embossed/printed metal plate or metallic foil with adhesive backing for permanent identification. Locate label so that it is readily visible and convenient for identification by Project Manager

25、 after installation of assembly. The label shall be approximately 1 inch x 3 inch (40 x 75 mm) and shall cite: 1. Manufacturers name/city/state. 2. Contract number. 3. Month/Year of manufacture. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-09 0

26、8 34 53 - 5 4. Mark number and Ballistic resistant rating. 1.7 DELIVERY, STORAGE AND HANDLING A. Deliver each assembly project site with fabrication, finishing, and assembly of primary panels, inserts, and frames completed and prepared for installation and connection with security systems. Disassemb

27、le hardware for shipping only to extent hardware interferes with shipping. B. Refer to Division One for shipping requirements. C. Provide removable spreader bar between jambs during fabrication, delivery, and installation and to include mullions of each frame assembly, except where integral threshol

28、d is required and serves same purpose. Do not mar finishes of assembly with installation or removal of spreader bars. D. Provide protection of pre-finished units, such as pre-finished with baked enamel or stainless steel, using self-adhesive paper. 1.8 APPLICABLE PUBLICATIONS A. The publications lis

29、ted below form a part of this specification to the extent referenced. The publications are referenced in the text by the basic designation only. SPEC WRITER NOTE: Delete publications which do not apply to the project. B. American National Standards Institute (ANSI): A250.8-2003 Recommended Specifica

30、tions for Standard Steel Doors and Frames (formerly SDI-100) A250.11-2001. . Recommended Erection Instructions for Steel Frames (formerly SDI-105) C. American Society for Testing and Materials (ASTM): A153/A153M-09 Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware A167-99(

31、2009) . Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip A653/A653M-09 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process Provided by IHSNot for ResaleNo reproduction or

32、 networking permitted without license from IHS-,-,-12-09 08 34 53 - 6 A1008/A1008M-09 Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable A1011/A1011M-09a. . Stand

33、ard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength D1044-08. Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion E2074-00. . Standard Test Method

34、 for Fire Tests of Door Assemblies, Including Positive Pressure Testing of Side-Hinged and Pivoted Swinging Door Assemblies D. National Fire Protection Association (NFPA): NFPA 80 - 2010. Standard for Fire Doors and Other Opening Protectives E. Society for Protective Coatings (SSPC): SSPC-SP 2 - 200

35、4. . Hand Tool Cleaning SSPC-SP 3 - 2004. . Power Tool Cleaning F. Underwriters Laboratories, Inc. (UL): UL752-2006. Bullet Resisting Equipment G. United States Department of State Bureau of Diplomatic Security (DS): SD-STD-01.01-1993 Certification Standard for Forced Entry and Ballistic Resistance

36、of Structural Systems H. United States General Services Administration (GSA): UFAS-1998 Uniform Federal Accessibility Standards SPEC WRITER NOTE: Update Product requirements to agree with applicable requirements (Types, Grades, Class, Tables, etc) specified in the referred. PART 2 - PRODUCTS Provide

37、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-12-09 08 34 53 - 7 2.1 MANUFACTURERS A. Certified units: provide units, including frames and sub-frames which are produced by manufacturer who has previously produced, within last 10 years, units of similar se

38、curity attack resistance of equivalent size and resistance ratings. 2.2 MATERIALS, GENERAL A. Hot-Rolled Steel Sheets and Strips: ASTM A1011, commercial quality, pickled and oiled, except as otherwise indicated. B. Cold-Rolled Steel Sheets: ASTM A1008, commercial quality, except as otherwise indicat

39、ed. C. Galvanized Steel Sheets: ASTM A653 with G90 zinc coating, mill phosphatized; commercial quality, except as otherwise indicated. D. Stainless Steel Sheets: AISI Type 302/304, complying with ASTM A 167; commercial quality, No. 4 directional polish. E. Supports and Anchors: Fabricate to endure r

40、equired performances, but of not less than 1/16 inch (1.5 mm) sheet steel. For exterior wall assemblies, hot-dip zinc coat support/anchor units after fabrication in compliance with ASTM A 153, Class B. F. Inserts, Bolts, Fasteners: Standard units of strengths required to endure performances; hot-dip

41、 zinc coated where used in exterior wall assemblies in compliance with ASTM A 153, Class C/D. G. Vision Lights General: Fabricate vision lights of sizes shown and scheduled with same performance capabilities as specified/shown for door assembly where installed. Where applicable, achieve performances

42、 and combined performances through lamination of transparent sheets, films, and screens of standard manufactured/tested products. Comply with applicable provisions of Division 8, Section 08 80 00, GLAZING. 1. Forced-Entry (FE) Resistance: Where assembly is indicated for forced-entry resistance ratin

43、g (FE), provide light of size shown or scheduled in accordance with certification. 2. Ballistic Resistance (BR): Where assembly is indicated for ballistic-resistance rating (BR), provide light of size shown or scheduled in accordance with certification. 3. Vision light faces general: Except as other

44、wise shown, where forced-entry or ballistic resistance is required, provide face of light exposed on exterior (to the “attack”) as glass surface, and where unit is of laminated construction, provide face Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-

45、,-12-09 08 34 53 - 8 exposed on interior (“safe”) as polycarbonate surface. Provide exposed polycarbonate surfaces to include an abrasion-resistant coating for 3 percent maximum haze increase for 100 revolutions on 500g Taber abraser, ASTM D 1044. 2.3 HARDWARE A. General: Provide special units of do

46、or hardware to achieve performances, and as shown and scheduled. Standard units for each security door assembly are specified to be furnished as work of Section 08 71 00, DOOR HARDWARE; see Project “Finish Hardware Schedule” and “Data Sheets,” and provisions of this Section, as well as notes on door

47、-and-frame schedule. 2.4 FABRICATION AND ASSEMBLY A. General: Fabricate, test, and preassemble security door assemblies with hardware at factory; disassemble hardware only to extent necessary for handling, packaging, shipment, and installation at Project. Fabricate metal work to comply with performa

48、nce requirements. Fabrications shall be rigid, neat, and free from warp/buckle/similar defects, with eased edges and continuously-welded joints, ground where exposed, to produce smooth, flush, invisible joints. Weld in accordance with AWS D1.1, Structural Welding Code for Steel: 1. Prepare panels an

49、d frames of each assembly to receive hardware, devices, and accessory units as shown and scheduled. Reinforce work for hardware and devices, and cut work for mortised or concealed units; comply with ANSI A115 series specifications, working from templates supplied by unit manufacturers and suppliers: a. Locate hardware, devices, and accessories as required by Section