VA 08 42 33-2011 REVOLVING DOOR ENTRANCES.pdf

1、10-11 08 42 33 - 1 SECTION 08 42 33 REVOLVING DOOR ENTRANCES SPEC WRITER NOTES: 1. Delete between / - / not applicable to project. Also delete any other item or Article not applicable in section and renumber paragraphs. 2. Industry cautions against use of manually initiated power assisted revolving

2、door when it shall be used in conjunction with building usage by elderly, due to possibility of door automatically advancing after being manually pushed to start power assist mechanism and catching elderly off balance. 3. Industry recommends that provision be made for installation of either automati

3、c single acting swing doors or automatic horizontal sliding doors on either side of revolving entrance doors for use by handicapped persons. Industry can provide a revolving entrance door package (10 foot diameter unit) to accommodate handicapped persons, as indicated below, but to date there has no

4、t been a Federal compliance act issued formerly for this item. PART I - GENERAL 1.1 DESCRIPTION A. Section includes: Revolving entrance doors including enclosures and related components as follows: 1. 3-wing / conventional manual / manually initiated power assisted / automatic / revolving doors. 2.

5、4-wing / conventional manual / manually initiated power assisted / automatic / revolving doors. /B. Include automatic operator. / /C. Adjacent sidelights and transom framing./ 1.2 RELATED WORK A. Sealing Joints. Section 07 92 00, JOINT SEALANTS. B. Aluminum hinged doors and storefront construction:

6、Section 08 41 13, ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS. C. Door operators: Section 08 71 13, AUTOMATIC DOOR OPERATORS. D. Lock cylinders: Section 08 71 00, DOOR HARDWARE. E. Glazing: Section 08 80 00, GLAZING. Provided by IHSNot for ResaleNo reproduction or networking permitted without license

7、from IHS-,-,-10-11 08 42 33 - 2 F. Finish Color: Section 09 06 00, SCHEDULE FOR FINISHES. G. Revolving darkroom doors: Section 08 34 36, DARKROOM DOORS. H. Electrical Rough-in and Final Connections are specified in Division 26, ELECTRICAL. I. Lighting: Section 26 51 00, INTERIOR LIGHTING. 1.3 QUALIF

8、ICATIONS A. Qualifications: 1. Approval is required of products or service of proposed manufacturer suppliers and installers, and will be based upon submission by Contractor of certification that: a. Manufacturer who regularly and presently, for last five years has manufactured and installed revolvi

9、ng entrance doors as one of its principal products. b. Installer: Approved by manufacturer. c. Manufacturers product submitted has been in satisfactory and efficient operation on minimum of three installations similar and equivalent to this project for past three years. 1.4 SUBMITTALS SPEC WRITER NO

10、TE: List below items Intended for use in project, necessary for review prior to manufacture. Refer to Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND SAMPLES for submittal requirements. Include additional submittal requirements for items specified. A. In accordance with Section 01 33 23, SHOP DRA

11、WINGS, PRODUCT DATA, AND SAMPLES. B. Manufacturers Literature and Product Data: 1. Manufacturers standard details and fabrication methods. 2. Data on finishing, hardware, components, and accessories. 3. Recommendations for maintenance and cleaning of exterior surfaces. C. Shop Drawings: 1. Submit co

12、mplete fabrication, installation, and associated components shop drawings. 2. Identify enclosures, speed control units, and other component parts, not included in manufacturers product data, by name and material and showing design, construction, installation, and anchorage. 3. Layout and installatio

13、n details, including relation to adjacent work. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 42 33 - 3 4. Elevation at 1:50 (1/4 inch) scale. 5. Hardware, show mounting heights. 6. Detail sections of typical composite members. 7. Provisio

14、ns for expansion and contraction. 8. Anchors and reinforcements. 9. Glazing details. 10. Equipment wiring diagram and electrical circuitry diagram for electric powered doors. D. Samples: 1. Submit pairs of samples of each specified color and finish on 300 mm (12 inch) long section by width of each t

15、ubular, or extruded shape section or 300 mm (12-inch) wide sections of sheet shapes. 2. Where normal color variations are anticipated, include 2 or more units in set indicating extreme limits of color variations. E. Quality Control Submittals: 1. Test Reports: Provide certified test reports from a q

16、ualified independent testing laboratory showing that revolving entrance door assembly has been tested in accordance with specified test procedures and complies with performance characteristics indicated. 2. Manufacturers Certificates: a. Stating that aluminum has been given specified thickness of an

17、odizing or organic coating finish. b. Indicating manufacturers and installers meet qualifications as specified. c. Submit list of equivalent size installations which have had satisfactory and efficient operation. 1.5 DELIVERY, STORAGE AND HANDLING Comply with Curtain Wall Manual No. 10. 1.6 APPLICAB

18、LE PUBLICATIONS A. Publications listed below form a part of this specification to extent referenced. Publications are referenced in text by basic designation only. B. American Architectural Manufacturers Association (AAMA): Curtain Wall Manual No. 10-Care and Handling of Architectural Aluminum from

19、Shop to Site. 2604-10 Specification for High Performance Organic Coatings on Architectural Aluminum Extrusions and Panels. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 42 33 - 4 C. American National Standards Institute/Builders Hardware a

20、nd Manufacturers Association (ANSI/BHMA): A156.10-11 . Power Operated Pedestrian Doors A156.19-07 . Power Assist and Low Energy Power Operated Doors. Z97.1-09 . Glazing Materials Used in Buildings, Safety Performance Specifications and Methods of Test. D. American Society for Testing and Materials (

21、ASTM): A167-99(R2009) . Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet and Strip. B209-07 Alum1num and Aluminum-Alloy Sheet and Plate. B221-08 Aluminum-Alloy Extruded Bars, Rods, Wire, Shapes, and Tubes. E283-04 Determining Rate of Air-Leakage through Exterior Windows, Curtain Walls

22、, and Doors Under Specified Pressure Differences Across this Specimen. E330-02(R2010) . Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference. E331-00(R2009) . Water Penetration of Exterior Windows Curtain Walls and Doors by Uniform Static Air

23、 Pressure Difference. E. National Association of Architectural Metal Manufacturer (NAAMM): AMP 500 Series . Metal Finishes Manual. 1.7 WARRANTY Warranty: Submit manufacturers written warranty for materials and installation, in accordance with Section 00 72 00, GENERAL CONDITIONS requirements except

24、that warranty period shall be extended to include three (3) years for revolving door units and five (5) years for speed control units and operator units. PART 2 - PRODUCTS 2.1 SYSTEM DESCRIPTION SPEC WRITER NOTE: Select desired door operation listed below and coordinate requirements of options liste

25、d below which are required for selected door operation. A. Design Requirements: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 42 33 - 5 1. Definitions: a. Manual Operation- Door operation provided by hand pressure applied against a movable

26、 revolving door surface which shall allow friction free door operation, through an adjustable speed control unit, of approximately 9 to 12 RPM maximum. b. Power Assist Operation: Door operation provided by hand pressure applied against a movable revolving door surface which shall turn on power assis

27、t electric operator and revolve door at rate of 2 to 10 RPM for one turn. Subsequent pushing on door shall reinstate one revolution. c. Automatic Operation: Door operation provided by use of a microwave motion detector placed to cover entire throat of entrance to revolving door to detect someone app

28、roaching door. This actuation shall cause door to revolve at rate of 4-8 RPM (adjustable) for one complete turn after actuating signal is removed, then stop and quarter point. d. Locate motor and controls for revolving doors in conditioned space. SPEC WRITER NOTE: Make material requirements agree wi

29、th applicable requirements specified in referenced Applicable Publications. Update and specify in both only that, which applies to project. 2.2 MATERIALS A. Aluminum: 1. Extruded: Provide alloy and temper recommended by manufacturer for type of use and finish indicated, but with not less strength an

30、d durability properties specified in ASTM B221 for 6063-T5. a. Provide main extrusions not less than 3 mm (0.125 inch) thick unless otherwise specified. b. Provide extruded aluminum glazing stops and other applied trim extrusions with a minimum wall thickness of 1.5 mm (0.062 inch). 2. Aluminum Shee

31、t: a. ASTM B209, alloy 5005-H34, except alloy used for color anodized aluminum shall be as required to produce specified color. b. Not less than 2 mm (0.080 inch) thick unless otherwise specified. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11

32、 08 42 33 - 6 B. Stainless Steel: ASTM A167 stainless steel sheet and formed members of /Type 302/304 alloy/ minimum 1.5 mm (0.0598 inch) thick unless otherwise specified. SPEC WRITER NOTE: It is not recommended that tinted glass be used in revolving door wings due to potential of not being able to

33、see person on other side of door. C. Glass and Glazing Material: 1. As specified in Section 08 80 00, GLAZING. 2. Accommodate up to 25 mm (1 inch) glazing. 3. Revolving door wings: a. Doors: 1) Wings: 6 mm (1/4 inch) tempered, 2) Clear tempered for use in flat sheets. 4. Curved Enclosure Walls: a. W

34、alls: /8 mm (5/16 inch)/ /11 mm (7/16 inch)/ laminated glass. b. Clear laminated for use in curved sheets. c. Tinted laminated for use in curved sheets. D. Glazing Cushions: Channel shaped of rubber, vinyl or polyethylene plastic. Terminate flanges flush with top of beads. 2.3 REVOLVING DOOR SPEC WR

35、ITER NOTES: 1. Many jurisdictions and structural performance codes do not permit use of revolving doors to satisfy emergency egress requirements. If codes permit use of revolving doors, determine factors to consider such as door width, acceptable building types, amount of exit width credit given, or

36、 similar limits. Size doors to comply with code requirements. 2. Ensure drawings indicate item stated in 2.2A. Use stock manufactured sizes. 3. Handicap Requirements: Although there is no formal handicap compliance requirement enacted as yet for revolving door industry, the industry will work with d

37、esigner to design revolving doors for handicapped person usage. There is a 10 foot diameter revolving door unit for use by handicapped persons. Contact your revolving door manufacturer to review and discuss design considerations. Provided by IHSNot for ResaleNo reproduction or networking permitted w

38、ithout license from IHS-,-,-10-11 08 42 33 - 7 4. Designer may also consider use of automatic swing out doors or automatic horizontal doors for use by handicapped persons adjacent to revolving door if space permits. 5. Automatic Doors and Power Assisted Doors and Low-Energy Power Operated Door compl

39、iance. a. Automatic Doors: Shall comply with ANSI/BHMA A156.10. b. Power-Assisted Doors and Low-Energy Power-Operated Doors: Shall comply with ANSI/BHMA A156.19. A. Design Requirements: 1. Drawings indicate size, profile and dimensional requirements of revolving entrance door assemblies required. 2.

40、 Enclosures: Circular metal panel and glass panel enclosure walls. 3. Canopy/Ceiling: Canopy ceiling, manual locks, operator, control, brake, sensor switch detectors power assisted. 4. Doors and Locks: 5. Manual Operation: / List Doors Nos. / 6. Power Assisted Operation: /List Doors Nos./ 7. Automat

41、ic Operation. /List Doors Nos./ 8. Design Wind Velocity: / To design pressure of .06 kPa (1.25 lb/sq ft) /_/ 9. Water Infiltration: Comply with requirements of ASTM E331. Test-pressure difference at which water penetration is to be determined, shall be 137 Pa (2.86 lb/ft2) /_ /. B. Performance Requi

42、rements: 1. Comply with performance requirements specified, by testing manufacturers assemblies according to test methods indicated. 2. Air Infiltration: Limit air leakage rate not to exceed 385462 cm3m (1.25 cfm) per m2 (square foot) of door area when tested in accordance with ASTM E283 at test pre

43、ssure differential of 7 kg/m2 (1.567 psf). 3. Water Infiltration: Unless otherwise specified, failure criteria of this test method shall be defined as water penetration beyond the vertical plane intersecting the innermost projection of testing specimen not including interior trim and hardware, when

44、tested in accordance with ASTM E331 at test pressure of 137 Pa (2.86 lbf/ft2) 2.4 FABRICATION A. Aluminum Doors: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-10-11 08 42 33 - 8 1. Cut and fit all related components in accordance with manufacturers

45、 recommendations. 2. Joints tightly bolted together. a. Bolt joints to produce hairline joints. b. Finish material prior to fabrication. c. Glass stops snap-in type. d. Assemble to prevent welds or adhesives from blemishing finished surfaces. e. Screws, and other fastenings, equally spaced, counters

46、unk, and finished to match adjacent surfaces. f. Enclosure constructed so that clearance is maintained and weather seal assured. g. Canopy: 1) Provide canopy to match contour of enclosure. 2) Canopy sides furnished in aluminum panel. Use aluminum clad plywood 1 mm/19 mm (.040/.75 inch) for interior

47、ceiling. Optional: Exterior roof fabricated from 2 mm (.090) anodized aluminum. h. Weather-stripping: 1) Provide EPDM sweep to door wings, sills, canopy and inner stiles, and combination EPDM/felt sweep to outer stiles and door wings. 2) Weather-stripping attached to wings easily adjustable and remo

48、vable without dismantling wings. i. Push Bars: Provide one on each wing. j. Deadlocks: Provide two with cylinders. C. Dissimilar Metals: Separate dissimilar metals with bituminous paint or other operator that will prevent galvanic action. D. Fasteners: Conceal fasteners wherever possible. Countersin

49、k heads of exposed fasteners. SPEC WRITER NOTES: 1. Retain paragraph E. if manual operation speed control is required. Coordinate to define location of different type doors on drawings. 2. Speed Control: Factory set and depends on door diameter. Refer to local codes for maximum limit imposed on size of each door. E. Manual Operation Speed Contro