VA 28 23 00-2011 VIDEO SURVEILLANCE.pdf

1、09-11 28 23 00 - 1 SECTION 28 23 00 VIDEO SURVEILLANCE SPEC WRITER NOTE: Delete / _ / if not applicable to project. Also delete any other item or paragraph not applicable in the section and renumber the paragraphs. Insert additional provisions as required for this project. PART 1 GENERAL 1.1 DESCRIP

2、TION A. Provide and install a complete Video Surveillance System, which is identified as the Video Assessment and Surveillance System hereinafter referred to as the VASS System as specified in this section. B. This Section includes video surveillance system consisting of cameras, data transmission w

3、iring, and a control station with its associated equipment. SPEC WRITER NOTE: Retain paragraph below if video surveillance will be integrated with one or more of other systems and integration requirements are specified in one of those system Sections. If retaining below, edit both paragraph above an

4、d paragraph below to coordinate with the scope of the Section that includes systems integration requirements. C. Video surveillance system Video assessment drawing submittals shall be per the established project schedule. D. Pre-installation design and as-built packages shall include, but not be lim

5、ited to: 1. Index Sheet that shall: a. Define each page of the design package to include facility name, building name, floor, and sheet number. b. Provide a list of all security abbreviations and symbols. c. Reference all general notes that are utilized within the design package. d. Specification an

6、d scope of work pages for all security systems that are applicable to the design package that will: 1) Outline all general and job specific work required within the design package. 2) Provide a device identification table outlining device Identification (ID) and use for all security systems equipmen

7、t utilized in the design package. 2. Floor plans, site plans, and enlarged plans shall: a. Include a title block as defined above. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 28 23 00 - 6 b. Define the drawings scale in both standard and me

8、tric measurements. c. Provide device identification and location. d. Address all signal and power conduit runs and sizes that are associated with the design of the electronic security system and other security elements (e.g., barriers, etc.). e. Identify all pull box and conduit locations, sizes, an

9、d fill capacities. f. Address all general and drawing specific notes for a particular drawing sheet. 3. A riser drawing for each applicable security subsystem shall: a. Indicate the sequence of operation. b. Relationship of integrated components on one diagram. c. Include the number, size, identific

10、ation, and maximum lengths of interconnecting wires. d. Wire/cable types shall be defined by a wire and cable schedule. The schedule shall utilize a lettering system that will correspond to the wire/cable it represents (example: A = 18 AWG/1 Pair Twisted, Unshielded). This schedule shall also provid

11、e the manufacturers name and part number for the wire/cable being installed. 4. A system drawing for each applicable security system shall: a. Identify how all equipment within the system, from main panel to device, shall be laid out and connected. b. Provide full detail of all system components wir

12、ing from point-to-point. c. Identify wire types utilized for connection, interconnection with associate security subsystems. d. Show device locations that correspond to the floor plans. e. All general and drawing specific notes shall be included with the system drawings. 5. A schedule for all of the

13、 applicable security subsystems shall be included. All schedules shall provide the following information: a. Device ID. b. Device Location (e.g. site, building, floor, room number, location, and description). c. Mounting type (e.g. flush, wall, surface, etc.). d. Power supply or circuit breaker and

14、power panel number. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 28 23 00 - 7 e. In addition, for the VASS Systems, provide the camera ID, camera type (e.g. fixed or pan/tilt/zoom (P/T/Z), lens type (e.g. for fixed cameras only) and housing

15、model number. 6. Detail and elevation drawings for all devices that define how they were installed and mounted. E. Pre-installation design packages shall be reviewed by the Contractor along with a VA representative to ensure all work has been clearly defined and completed. All reviews shall be condu

16、cted in accordance with the project schedule. There shall be four (4) stages to the review process: 1. 35 percent 2. 65 percent 3. 90 percent 4. 100 percent F. Provide manufacturer security system product cut-sheets. Submit for approval at least 30 days prior to commencement of formal testing, a Sec

17、urity System Operational Test Plan. Include procedures for operational testing of each component and security subsystem, to include performance of an integrated system test. G. Submit manufactures certification of Underwriters Laboratories, Inc. (UL) listing as specified. Provide all maintenance and

18、 operating manuals per the VA General Requirements, Section 01 00 00, GENERAL REQUIREMENTS. H. Submit completed System Readiness Checklists provided by the Commissioning Agent and completed by the contractor, signed by a qualified technician and dated on the date of completion, in accordance with th

19、e requirements of Section 28 08 00 COMMISSIONING OF ELECTRONIC SAFETY AND SECURITY SYSTEMS. 1.6 APPLICABLE PUBLICATIONS A. The publications listed below (including amendments, addenda, revisions, supplement, and errata) form a part of this specification to the extent referenced. The publications are

20、 referenced in the text by the basic designation only. B. American National Standards Institute (ANSI)/Electronic Industries Alliance (EIA): 330-09 . Electrical Performance Standards for CCTV Cameras Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09

21、11 28 23 00 - 8 375A-76 Electrical Performance Standards for CCTV Monitors C. Institute of Electrical and Electronics Engineers (IEEE): C62.41-02 IEEE Recommended Practice on Surge Voltages in Low-Voltage AC Power Circuits 802.3af-08 . Power over Ethernet Standard D. Federal Communications Commisio

22、n (FCC): (47 CFR 15) Part 15 Limitations on the Use of Wireless Equipment/Systems E. National Electrical Contractors Association (NECA): 303-2005 . Installing Closed Circuit Television (CCTV) Systems F. National Fire Protection Association (NFPA): 70-08 Article 780-National Electrical Code G. Federa

23、l Information Processing Standard (FIPS): 140-2-02 . Security Requirements for Cryptographic Modules H. Underwriters Laboratories, Inc. (UL): 983-06 . Standard for Surveillance Camera Units 3044-01 Standard for Surveillance Closed Circuit Television Equipment 1.7 COORDINATION A. Coordinate arrangeme

24、nt, mounting, and support of video surveillance equipment: 1. To allow maximum possible headroom unless specific mounting heights that reduce headroom are indicated. 2. To provide for ease of disconnecting the equipment with minimum interference to other installations. 3. To allow right of way for p

25、iping and conduit installed at required slope. 4. So connecting raceways, cables, wireways, cable trays, and busways will be clear of obstructions and of the working and access space of other equipment. B. Coordinate installation of required supporting devices and set sleeves in cast-in-place concre

26、te, masonry walls, and other structural components as they are constructed. C. Coordinate location of access panels and doors for video surveillance items that are behind finished surfaces or otherwise concealed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

27、om IHS-,-,-09-11 28 23 00 - 9 1.8 WARRANTY OF CONSTRUCTION A. Warrant VASS System work subject to the Article “Warranty of Construction” of FAR clause 52.246-21. B. Demonstration and training shall be performed prior to system acceptance. PART 2 PRODUCTS SPEC WRITER NOTE: Delete or amend all paragra

28、phs and sub-paragraphs as needed to ensure that only the equipment required per the Request for Proposal (RFP) is provided. 2.1 GENERAL SPEC WRITER NOTE: Erase paragraph below if analog/hybrid cameras are not used in the project. A. Video signal format shall comply with the NTSC standard composite v

29、ideo, interlaced. Composite video signal termination shall be 75 ohms. B. Surge Protection: Protect components from voltage surges originating external to equipment housing and entering through power, communication, signal, control, or sensing leads. Include surge protection for external wiring of e

30、ach conductor entry connection to components. C. Power Connections: Comply with requirements in Section 28 05 00 COMMON WORK REQUIREMENTS FOR ELECTRONIC SAFETY AND SECURITY, Part 2, as recommended by manufacturer for type of line being protected. D. Tamper Protection: Tamper switches on enclosures,

31、control units, pull boxes, junction boxes, cabinets, and other system components shall initiate a tamper-alarm signal when unit is opened or partially disassembled. Control-station, control-unit alarm display shall identify tamper alarms and indicate locations. 2.2 CAMERAS A. All Cameras will be EIA

32、 330 and UL 1.Minimum Protection for Power Connections 120 V and more: Auxiliary panel suppressors shall comply with requirements in Section 28 05 00 COMMON WORK REQUIREMENTS FOR ELECTRONIC SAFETY AND SECURITY, Part 2. B. Minimum Protection for Communication, Signal, Control, and Low-Voltage 983 com

33、pliant as well as: Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 28 23 00 - 10 1. Will be charge coupled device (CCD cameras and shall conform to National Television System Committee (NTSC) formatting. 2. Fixed cameras shall be color and the

34、primary choice for monitoring following the activities described below. Pan/Tilt/Zoom (P/T/Z) cameras shall be color and are to be utilized to complement the fixed cameras. SPEC WRITER NOTE: Leave one of two following paragraphs. 3. Shall be powered by either 12 volts direct current (VDC) or 24 volt

35、s alternate current (VAC). Power supplies shall be Class 2 and UL compliant and have a back-up power source to ensure cameras are still operational in the event of loss of primary power to the VASS System. SPEC WRITER NOTE: Leave next subparagraph if IP PoE cameras are part of the VASS. 4. Shall be

36、powered over Ethernet. Network switches supporting PoE cameras shall have a back-up power source to ensure cameras are still operational in the event of loss of primary power to the VASS System. 5. Shall be rated for continuous operation under the environmental conditions listed in Part 1, Project C

37、onditions. SPEC WRITER NOTE: Erase paragraph 2.2 A 6 if only IP cameras are specified. 6. Will be home run to a monitoring and recording device via a controlling device such as a matrix switcher or network server and monitored on a 24 hour basis at a designated Security Management System location. 7

38、 Each function and activity shall be addressed within the system by a unique user defined name, with minimum of twenty (20) characters. The use of codes or mnemonics identifying the VASS action shall not be accepted. SPEC WRITER NOTE: Revise 2.1 A 8) if video motion detection function is the featur

39、e of Video Management System (VMS). The Video Motion Detection (VMD) is required either on camera or head-end side (DVR, HDVR, NVR or VMS). Specify the Video Motion Detection requirements as appropriate for the application. 8. Shall come with built-in video motion detection that shall automatically

40、monitor and process information from each camera. The camera motion detection shall detect motion within the cameras Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 28 23 00 - 11 field of view and provide automatic visual, remote alarms as a re

41、sult of detected motion. SPEC WRITER NOTE: Erase 2.1 A 9) for cameras in the areas with constant light levels. 9. Shall be programmed to digitally flip from color to black and white at dusk and vice versa at low light conditions. 10. Will be fitted with AI/DC lenses to ensure the image quality under

42、 different light conditions. 11. P/T/Z cameras shall be utilized in a manner that they complement fixed cameras and shall not be used as a primary means of monitoring activity. 12. Dummy or fake cameras will not be utilized at any time. 13. Appropriate signage shall be designed, provided, and posted

43、 that notifies people that an area is under camera surveillance. SPEC WRITER NOTE: Retain Paragraph 2.3 if VASS is based on analog cameras. 2.3 VIDEO MANAGEMENT SYSTEM (ANALOG) A. The Video Management System (VMS)shall provide features and functions as specified below: 1. Supports minimum of 20 clie

44、nt connections. 2. The Video Management System shall be capable of recording more than 32 days on 1.6 TB of internal hard drive storage using the following parameters: a. Resolution 4CIF b. Video Mode NTSC c. Quality Normal d. Sensitivity Normal e. Number of Cameras 16 f. Record Audio On g. Motion 5

45、0% . 3. The Digital Video Management System shall, at a minimum, combine multiplexing, alarm detection, video motion detection, video, audio, and text recording. B. System Chassis 1. The Video Management System must utilize a chassis no larger than three rack units in height, and be suitable for eit

46、her desktop or rack mount installations. The unit must fit within a standard video rack as well as a server rack. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-09-11 28 23 00 - 12 2. The Video Management Systems chassis shall include three indicato

47、r lights easily viewed from the front panel. These indicator lights must be colored red, yellow, and green to signify system status. 3. The Video Management Systems chassis shall incorporate a minimum of four front accessible, swappable drive bays. The bays must be behind a locking front cover that

48、restricts access not only to the drives, but also to the power switch and reset switch. C. Operating System 1. The Video Management Systems operating system and application must be installed on a separate solid-state system drive (flash memory card), with no moving parts to wear out or fail, to redu

49、ce the risk of system failure. Units with the operating system and/or application installed on a hard drive are not acceptable. D. Recording 1. The Digital Video Management System shall use record mode settings as continuous or event activated. 2. The Digital Video Management System shall provide for simultaneous recording, playback, transmitting,