EN 15085-2-2007 英文版 Railway applications- Welding of railway vehicles and components- Par T 2 Quality requirements and certification of welding manufacturer.pdf

1、EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15085-2October 2007ICS 25.160.10; 45.060.01English VersionRailway applications - Welding of railway vehicles andcomponents - Part 2: Quality requirements and certification ofwelding manufacturerApplications ferroviaires - Soudage des vhicules et desc

2、omposants ferroviaires - Partie 2: Exigences de qualit etcertification du constructeurBahnanwendungen - Schweien von Schienenfahrzeugenund -fahrzeugteilen - Teil 2: Qualittsanforderungen undZertifizierung von SchweibetriebenThis European Standard was approved by CEN on 18 August 2007.CEN members are

3、 bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the

4、 CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same sta

5、tus as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, S

6、lovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide

7、 for CEN national Members.Ref. No. EN 15085-2:2007: EEN 15085-2:2007 (E) 2 Contents Page Foreword.3 Introduction .4 1 Scope .5 2 Normative references .5 3 Terms and definitions .6 4 Certification of welding manufacturers.6 5 Quality requirements for the welding manufacturer.8 5.1 Staff requirements

8、.8 5.2 Technical requirements .10 5.3 Welding coordination organization.11 5.4 Welding procedure specification .11 5.5 Assignment of the requirements to certification level.11 6 Certification procedure .11 6.1 Audit for the certification .11 6.2 Certificate .12 7 Validity .12 Annex A (informative) P

9、ossible allocation of parts and subassemblies of rail vehicles to the certification levels.14 Annex B (normative) Tasks and areas of competence of the welding coordinator.16 Annex C (normative) Requirements for the welding manufacturer .19 Annex D (informative) Welding of railway vehicles and compon

10、ents according to EN 15085-2 .21 Bibliography .22 EN 15085-2:2007 (E) 3 Foreword This document (EN 15085-2:2007) has been prepared by Technical Committee CEN/TC 256 “Railway applications”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standar

11、d, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the latest by April 2008. This series of European Standards EN 15085 Railway applications Welding of railway vehicles and components consists of the

12、following parts: Part 1: General Part 2: Quality requirements and certification of welding manufacturer Part 3: Design requirements Part 4: Production requirements Part 5: Inspection, testing and documentation Attention is drawn to the possibility that some of the elements of this document may be th

13、e subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgi

14、um, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 15085-2:2007 (E)

15、 4 Introduction Welding is a special process in the manufacture of railway vehicles and their parts. The required provisions for this process are laid down in the standards series EN ISO 3834. The basis of these provisions are the basic technical welding standards in respect of the special requireme

16、nts for the construction of railway vehicles. This standard is aimed at defining the terms of enforcement applicable to European Standards, it should not be construed as a substitute to these standards. This standard can also be used by internal and external parties, including certification bodies,

17、to assess the organisations ability to meet customer, regulatory and the organisations own requirements. EN 15085-2:2007 (E) 5 1 Scope This series of standards applies to welding of metallic materials in the manufacture and maintenance of railway vehicles and their parts. This part of the series def

18、ines the certification levels as well as the requirements for welding manufacturers and describes the procedure for the recognition of welding manufacturers. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only t

19、he edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 287-1, Qualification test of welders Fusion welding Part 1: Steels EN 473, Non destructive testing Qualification and certification of NDT personnel General principle

20、s EN 1418, Welding personnel Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials EN 15085-1:2007, Railway applications - Welding of railway vehicles and components - Part 1: General EN 15085-3:2007, Rai

21、lway applications Welding of railway vehicles and components Part 3: Design requirements EN 15085-4:2007, Railway applications Welding of railway vehicles and components Part 4: Production requirements EN ISO 3834 (all parts), Quality requirements for fusion welding of metallic materials EN ISO 9606

22、-2, Qualification test of welders - Fusion welding - Part 2: Aluminium and aluminium alloys (ISO 9606-2:2004) EN ISO 14555, Welding - Arc stud welding of metallic materials (ISO 14555:2006) EN ISO 14731:2006, Welding coordination - Tasks and responsibilities (ISO 14731:2006) EN ISO 15607, Specificat

23、ion and qualification of welding procedures for metallic materials - General rules (ISO 15607:2003) EN ISO 15609 (all parts), Specification and qualification of welding procedures for metallic materials Welding procedure specification EN ISO 15610 Specification and qualification of welding procedure

24、s for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) EN ISO 15611, Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) EN ISO 15612, Specification and qualification

25、 of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) EN ISO 15613, Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) EN 15085-2:2007

26、(E) 6 EN ISO 15614 (all parts)1)Specification and qualification of welding procedures for metallic materials Welding procedure test EN ISO 15620, Welding - Friction welding of metallic materials (ISO 15620:2000) EN ISO/IEC 17025, General requirements for the competence of testing and calibration lab

27、oratories (ISO/IEC 17025:2005) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 15085-1:2007 apply. 4 Certification of welding manufacturers The quality requirements for welding manufacturers, which carry out welding work on rail vehicles, components a

28、nd sub-assemblies, are specified by the standard series EN ISO 3834. Dependant on the certification level, the requirements of EN ISO 3834-2, EN ISO 3834-3 or EN ISO 3834-4 shall be fulfilled in principle (see Annex A). Welding manufacturers, which carry out welding work on railway vehicles, compone

29、nts and sub-assemblies, shall be certified according to this standard, if specified. Compliance with the requirements shall be checked and certified by a recognised manufacturer certification body (see Clause 6). Four certification levels (CL) are laid down for the certification of welding manufactu

30、rers (Level 1 to Level 4). Level 1 to Level 3 depends on the weld performance classes CP A to CP D of the welded joints specified in EN 15085-3:2007, Table 2. Table 1 contains a description of the certification level and the allocation in the weld performance classes. The required certification leve

31、l depends on the following two items: 1) Table 1; 2) safety relevance of the components or sub-assemblies where the welded part is integral (see list beneath Table 1). 1) For railway applications, only EN ISO 15614-1, EN ISO 15614-2, prEN ISO 15614-3, EN ISO 15614-4, EN ISO 15614-7, EN ISO 15614-11,

32、 EN ISO 15614-12 and EN ISO 15614-13 are relevant. EN 15085-2:2007 (E) 7 Table 1 Certification level Description Certification leve (CL) This level applies to welding manufacturers which manufacture welded railway vehicles or their welded parts with welded joints classified in weld performance class

33、es CP A to CP D. Certification level CL 2 to CL 4 is included. CL 1 This level applies to welding manufacturers which manufacture welded parts of railway vehicles with welded joints classified in weld performance classes CP C2 to CP D. Welded joints classified in weld performance class CP C1 are inc

34、luded if these welds are checked according to weld inspection class CT 1 according to EN 15085-5:2007, Table 1. Certification level CL 4 is only included according to welded joints of certification level CL 2 or CL 3. CL 2 This level applies to welding manufacturers which manufacture welded parts of

35、 railway vehicles with welded joints classified in weld performance class CP D. CL 3 This level applies to manufacturers which do not weld but design railway vehicles and parts of rail vehicles or buy and assemble or sell them. Certification not required for welding works of certification level CL 3

36、. CL 4 Because of their safety relevance the following components and sub-assemblies shall be welded by welding manufacturers with a certification level CL 1. bogie frames and bolsters; body shell components (e.g. under frames, structures); buffers and draw gear; wheel set components (e.g. wheel set

37、 mountings, axle boxes, spring supports); brake equipment (e.g. magnetic track brake, brake rods, brake triangles, brake cylinders, brake cross beams); supporting frames for heavy components (e.g. traction units, pantographs); welded components for drag transmission from bogie to vehicle; vibration

38、dampers and their link between bogie and vehicle or between vehicles; finishing welding of castings within components indicated above; external fuel tanks. Annex A contains information about possible classifications of the certification levels for further components and sub-assemblies of railway veh

39、icles. EN 15085-2:2007 (E) 8 According to EN 15085-3:2007, certification level CL 1 to CL 3 necessary for the product shall be clearly indicated in the engineering documentation (e.g. on the drawings). If required by the customer, the certification level shall be agreed with him respecting the natio

40、nal safety authority. 5 Quality requirements for the welding manufacturer 5.1 Staff requirements 5.1.1 Welders and welding operators The welding manufacturer shall have welders and welding operators with qualification in accordance with EN 287-1, or EN ISO 9606-2 or with EN 1418. Qualification shall

41、 cover each the welding processes, material groups, joint types and welding positions needed for production. Such qualification should be carried out by either: accredited examining body, responsible welding coordinator of the manufacturer, recognised by the manufacturer certification body as specified in 5.1.2. If fillet welds are done in production a fillet weld test piece is necessary. 5.1.2 Welding coordination The welding manufacturer shall have suitably experienced welding coordinators with the relevant technical knowledge according to EN ISO 14731. The manufacturer shall clearly pr