NASM 14191-2001 recess - offset cruciform, ribbed dimensions of recess, gage and diuver for.pdf

1、NASM 14191-2001 recess - offset cruciform, ribbed dimensions of recess, gage and diuver for_. t- .Y= FED SUI CLASS 53GP. R RN) 4 WCS MWUACD ALON PU (YI f 13 (ITP WHC WULS OF 7u 4 PLACES NOTES. . . - . - -. 1. DIMENSIONSARE IN INCHES 2. THE SPECIFIC PART STANDARD OR DRAWNG WHICH SPECIFIES THIS RECESS

2、 DRIVE BY REFERENCING THIS DOCXMENT SHALL SPEClM VALUES FOR DIMENSIONS J. W. T. AND DEPTH OF GAGE PENETRATION. IF THE VALUES SPECIFIED HEREIN ARE NOT COMPATIBLE WTH THE PART CONFIGURATION OR PERFORMANCE REQUIREMENTS. 3. RECESSES SHALL HAVE RIBS ON AT LEAST THE LOWER 75 PERCENT OF THE REMOVAL WALL OF

3、 EACH or THE FOUR WGS. 4 DELETED. 5. FOR DIMENSIONS OF NON-RIBBED RECESSES SIZES OTHROUGH 518 INCH, SEE NASM33781. 6. CERTAIN PROVISIONS OF MIS WCUMEKT ARE THE SUBJECT OF INTERNATIONAL STANDARDIZATION AGREEMENTS NATO STANAG 3802 WEN CHANCE NOTICE, REVISION OR CANCELLATION OF THIS WCUMENT IS PROPOSED

4、 WHICH WLL AFFECT OR VIOLATE THE INTERNATIONAL AGREEMENT CONCERNED. THE PREPARING ACTIVITY SHALL TAKE APPROPRIATE RECONCILIATION ACTION THROUGH INTERNATIONALSTANDARDIZATION CHANNELS. INCLUDING DEPARTMENTAL STANDARDIZATION OFFICES, IF RFOlllRFD PERMISSION OF ME PHILLIPS SCREW COMPANY. THE INITIAL REL

5、EASE OF THIS DOCUMENT SUPERSEDES MS14191 E LIST OF CURRENT SHEETS No. I REV. I o NEW NEW CUSTODlAN NATIONAL AEROSPACE STANDARDS COMMITTEE SPEClFICAllON NONE TlllKD fWG LE PKOJECIION I I CLASWICA170N DESIGN SThN1)hlW RECESS - OFFSET CRUCIFORM, RIBBED DIMENSIONS OF RECESS, GAGE AND DIUVER FOR i NASM14

6、191 SllEET 1 OF G COPYRIGHT Aerospace Industries Association of America, Inc. (AIA/NAS)Licensed by Information Handling ServicesAerospace NATIONAL AEROSPACE STANDARD Industries COPYRIGHT Aerospace Industries Association of America, Inc. (AIA/NAS)Licensed by Information Handling Services5/16 .O860 .

7、. COPYRIGHT Aerospace Industries Association of America, Inc. (AIA/NAS)Licensed by Information Handling ServicesAerospace NATIONAL AEROSPACE STANDARD Industries hso(jation 0 COPYRIGHT 19Q8AEROSPACE INWSlRlES ASSOClATlON OF AMERICA, INC. ALL RIGHTS RESERVED COPYRIGHT Aerospace Industries Association

8、of America, Inc. (AIA/NAS)Licensed by Information Handling ServicesAerospace NATIONAL AEROSPACE STANDARD Industries Ass(jatiorl OCOPYRlGW 1898 AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA. INC. ALL RIGHTS RESERVED COPYRIGHT Aerospace Industries Association of America, Inc. (AIA/NAS)Licensed by Inform

9、ation Handling ServicesAerospace NATIONAL AEROSPACE STANDARD Industries Association CCOPYRlGHT 2001 AEROSPACE INDUSTRIES ASSOCIATlON OF AMERICA INC ALL RIGHTS RESERVED NOTES 1. DIMENSIONS ARE IN INCHES. 2. DRIVERS SHALL HAVE RIBS ON THE REMOVAL WALL OF EACH WING. 3. SEE MIL-B85643 FOR BIT PROCUREMEN

10、T. 4. DELETED. 5. FOR DIMENSIONS OF NON-RIBBED DRIVERS, SIZES O THROUGH 518 INCH, SEE NASM33781. 5. THIS IS A DESIGN SPECIFICATION NOT TO BE USED AS A PART NUMBER. 7. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS DOCUMENT AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS DOCUMENT SHALL TAKE PR

11、ECEDENCE, 8. UNLESS OTHERWSE SPECIFIED, ISSUES OF REFERENCED DOCUMENTS ARE THOSE IN EFFECT AT THE TIME OF SOLICITATION. NASM14191 Y;FTFF.T 6 USE OF OR RELIANCE UPON T)IlS DONMENTOR ANY NATIONAL AEROSPACE STANDARD IS ENllRELY VOLUNTARY. AIA WES NOT QUAI.IFY SVPPI.IERS OR CERTIFY CONFORMANCE OF ITEMS

12、FROCURED UNDER NATIONAL AEROSPACE STANDARDS. AIA MAKES NO REPRESENTATlON OR CLAIM RESFECTnNG (1)T)IE SUITAAILTTY OF mMS FOR ANY PARTlCVWR APPLICATION. OR (2)llIE EXISENCE OFOR APFLICABlLrrY TNERFID OF PATENTOR TRADEMARK RIGlK5. COPYRIGHT Aerospace Industries Association of America, Inc. (AIA/NAS)Licensed by Information Handling Services主营业务范围：ASTM、NAS、NASM、MIL、ISOOOO、EN、DIN等技术标准翻译；技术资料翻译。业务QQQQQQQQ：2298175560专业诚信质量不满意，可不付款专注于技术翻译