IEC 60130-8-1976 Connectors for frequencies below 3 MHz Part 8 Concentric connectors for audio circuits in radio receivers《频率低于3MHz的连接器 第8部分 无线电设备中音频线路用同心连接器》.pdf

1、NORME INTERNATIONALE INTERNATIONAL STANDARD CE1 IEC 130-8 Deuxime dition Second edition 1 976-0 1 Connecteurs utiliss aux frquences jusqu 3 MHz Huitime partie: Connecteurs concentriques pour circuits audio de postes de radio Connectors for frequencies below 3 MHz Part 8: Concentric connectors for au

2、dio circuits in radio receivers Numro de rfrence Reference number CEI/IEC 130-8: 1976 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Numros des publications Depuis le ler jan

3、vier 1997, les publications de la CE1 sont numrotes partir de 60000. Publications consolides Les versions consolides de certaines publications de la CE1 incorporant les amendements sont disponibles. Par exemple, les numros ddition 1.0, 1.1 et 1.2 indiquent respectivement la publication de base, la p

4、ublication de base incorporant lamendement 1, et la publication de base incorporant les amendements 1 et 2. Validit de la presente publication Le contenu technique des publications de la CE1 est constamment revu par la CE1 afin quil reflte Itat actuel de la technique. Des renseignements relatifs la

5、date de reconfirmation de la publication sont disponibles dans le Catalogue de la CEI. Les renseignements relatifs des questions ltude et des travaux en cours entrepris par le comit technique qui a tabli cette publication, ainsi que la liste des publications tablies, se trouvent dans les documents c

6、i- dessous: b) un numro de srie indiquant le type (voir larticle 3). Exemple: 130-8 IEC-O1 indique une embase femelle type 1. 3. Dimensions Les dimensions originales sont en inches. Les dessins et les tableaux spcifiant les dimensions essentielles sont donnes aux pages 6, 7, 8, et 9. Note. - La form

7、e des connecteurs peut diffrer de celle indique dans les figures 1 et 2, pages 6 et 7, condition que les dimensions spcifies ne soient pas modifies. Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without

8、 license from IHS-,-,-5- CONNECTORS FOR FREQUENCIES BELOW 3 MHz Part 8 : Concentric connectors for audio circuits in radio receivers 1. Scope This standard covers two fixed socket connectors for use in audio circuits for the connection of earphones and loudspeakers. Noie. - Special precautions shall

9、 be taken to comply with the safety requirements according to IEC Publication 65, Safety Requirements for Mains Operated Electronic and Related Apparatus for Household and Similar General Use, in all radio receivers capable of being connected to mains-operated battery eliminators. 2. IEC type design

10、ation Connectors according to this standard shall be designated by : a) 6) Example: 130-8 1 E C-O1 denotes a fixed socket connector Type 1. the reference to this standard: 130-8 IEC-; a serial number denoting the type (see Clause 3). 3. Dimensions The original dimensions are in inches. .Drawings and

11、 tables giving the essential dimensions are given on pages 6, 7, 8 and 9. Note. - The shape of the connectors may deviate from those given in Figures 1 and 2, pages 6 and 7, provided that the specified dimen- sions are not affected. Copyright International Electrotechnical Commission Provided by IHS

12、 under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-6- I I 0.470 0.094 0.469 - 0.147 0.512 0.360 EMBASE FEMELLE TYPE 1 FEED SOCKET CONNECTOR TYPE 1 0.440 - - 0.150 0.143 0.340 - 130-8 IEC-O1 Notes Lfrence Leferencc a b3 d e f g4 C Douille de mont

13、age Mounting bushing FIGURE 1 1, 2, TABLEAU I TABLE I 124176 max. rnm min. 11,94 2,40 11,9i 3,74 13,Oi 9.14 - Le connecteur peut de plus tre prvu soit avec un ressort de shuntage, soit avec un ressort de shuntage et un ressort dtablissement du circuit. Diamtre du trou de passage: 6,8 0,3 mm (0,268 h

14、owever, when socket and gauge are fully mated, the tip spring must override 0.38 mm (0.015 in) min. to 1.90 mm (0.075 in) max. (see drawing below). Both maximum and minimum gauges must be used in accordance with the schedule for type tests. 0,38 mm min. 1,90 mm max. % -, 0.015 in min. to 0.075 in ma

15、x. 127176 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.2 Calibre pour le connecteur type 2 Matriau: laiton, nickel. 734 10,41 8,67 2,47 0,56 1.93 2,49 1.12 -9- 4.2 Gauge

16、for connector Type 2 Material : brass, nickel-plated. 6,78 9,65 8,26 2,21 0,30 1,88 29 0,86 Matriau isolant 0.297 0.410 0.345 0.097 0.022 0.076 0.098 0.044 Insulating material 0.267 0.380 0.325 0.087 0.012 0.074 0,096 0.034 lfrena leference h i k I rn n P 9 128176 FIGURE 4 TABLEAU IV TABLE IV mm max

17、. I min. Notes Lexcentricit de c In et p ) ne doit pas tre sup- rieure 0,15 mm (0,006 in). La configuration du ressort dextrmit par rapport au manchon est facultative, mais quand le manchon et le calibre sont accoupls compltement, le ressort dextrmit doit dpasser 0,38 mm (0,015 in) min. 1,4 mm (0,05

18、5 in) max. (voir dessin ci-dessous). Deux calibres, maximal et minimal, doivent tre utiliss conformment au programme des essais de type. in max. I min. Notes Eccentricity of “I” and “p” shall not exceed 0.15 mm (0.006 in). Configuration of tip spring on mating socket is optional ; however, when sock

19、et and gauge are fully mated, the tip spring must override 0.38 mm (0.015 in) min. to 1.4 mm (0.055 in) max. (see drawing below). Both maximum and minimum gauges must be used in accordance with the schedule for type tests. Dpass Override 0,38 mm min. 1,4 mm max. 0.015 in min. to 0.055 in max. 129176

20、 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 10 - 5. circuits Contact normal 7“ Shuntage supplmentaire - Shuntage et contact supplmentaires 6. Programme des essais de typ

21、e v+ A Ce programme indique tous les essais et leur ordre dexcution ainsi que les conditions requises pour chaque type dembase. Essai Examen visuel Dimensions Rsistance de contact Rsistance disolement Rigidit dilectrique Force de rtention du calibre a) Force dinsertion b) Force dextraction Essai den

22、durance mcanique Pertes dilectriques Article et paragraphe de la Publication 130-1 de la CE1 11 12 14.1 14.4 14.5 15.2 16.1 16.1 19 - I Conditions dessai Conditions requises Type 1 Type 2 Avec ia broche dessai Mesure entre tous les contacts et toutes les autres parties conduc- trices A la rception E

23、ntre le ressort dextr- mit ou le ressort de shuntage et ia douille cace E = 250 V valeur effi- Masse (poids) du calibre minimal: 30 g Utilisant le calibre maximal Utilisant le calibre minimal Avec la broche dessai Sec 0, i2 max. 0.1 R max. 100 Ma min. 75 Ml2 min. 11 N max. 0,6 N min. 16 Nmax. 1,l N

24、min. 2,2 N min.* 5 O00 manuvres 2 500 manuvres 0,05 % 0,05 % * Applicable uniquement aux types munis de ressort de shuntage. Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- 1

25、1 - 5. circuits Normal make contact Additional shunt contact Additional shunt and make contact 6. Schedule for type tests This schedule shows all tests and the order in which they shall be carried out, as well as the requirements for each type of fixed connector. I Test Clause and sub-clause of IEC

26、Publication 130-1 Visual inspection Dimensions Contact resistance Insulation resistance Voltage proof Gauge retention force a) Insertion force b) Withdrawal force Mechanical endurance test Dielectric loss 11 12 14.1 14.4 14.5 i 5.2 16.1 16.1 19 Conditions of test Using test pin Measured between all

27、contacts and all other conducting parts As received Between tip spring or shunt circuit spring and bushing E = 250 V r.m.s. Mass (weight) of mini- mum gauge: 30 g Using maximum gauge Using minimum gauge Using test pin Requirements Type 1 Type 2 0.1 Ci max. 0.1 R max. 100 MR min. 75 MR min. 16 N max.

28、 11 N max. 1.1 N min. 2.2 N min.* 5 O00 operations 0.6 N min. 2 500 operations 0.05 % 0.05 % * Only applicable for types with shunt circuit spring. Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without

29、license from IHS-,-,-Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo

30、 reproduction or networking permitted without license from IHS-,-,-ICs 31.220.10 Typeset and printed by the IEC Central Office GENEVA, SWITZERLAND Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-