IEC 60317-0-7-2012 Specifications for particular types of winding wires - Part 0-7 General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire with nominal.pdf

1、 IEC 60317-0-7 Edition 1.0 2012-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 0-7: General requirements Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm Spcifications pour

2、types particuliers de fils de bobinage Partie 0-7: Exigences gnrales Fil de section circulaire en cuivre maill sans dfaut disolation lectrique avec diamtre nominal de conducteur compris entre 0,040 mm et 1,600 mm IEC60317-0-7:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, S

3、witzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the co

4、untry of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contrai

5、re, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions

6、sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20

7、 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC pub

8、lications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteri

9、a (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and al

10、so once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnic

11、al Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire

12、 organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition

13、la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informatio

14、ns sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - w

15、ww.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (V

16、EI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60317-0-7 Edition 1.0 2012-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding

17、wires Part 0-7: General requirements Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm Spcifications pour types particuliers de fils de bobinage Partie 0-7: Exigences gnrales Fil de section circulaire en cuivre maill sans dfaut diso

18、lation lectrique avec diamtre nominal de conducteur compris entre 0,040 mm et 1,600 mm INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE R ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-88912-043-7 Registered trademark of the International Electrotechnical Commissio

19、n Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60317-0-7 IEC:2012 CONTENTS FOREWORD . 4 INTRODUCTI

20、ON . 6 1 Scope . 7 2 Normative references . 7 3 Terms, definitions, general notes and appearance 7 3.1 Terms and definitions 7 3.2 General notes 9 3.2.1 Methods of test 9 3.2.2 Winding wire 9 3.3 Appearance . 9 4 Dimensions 9 4.1 Conductor diameter . 9 4.2 Out of roundness of conductor (for nominal

21、diameters over 0,063 mm) 10 4.3 Minimum overall diameter 10 4.4 Maximum overall diameter . 10 5 Electrical resistance . 13 6 Elongation 13 7 Springiness 14 8 Flexibility and adherence 14 8.1 Mandrel winding test (for nominal conductor diameters up to and including 1,600 mm) . 14 8.2 Jerk test (for n

22、ominal diameters up to and including 1,000 mm) 15 9 Heat shock . 15 10 Cut Through . 16 11 Resistance to abrasion . 16 12 Resistance to solvents 16 13 Breakdown voltage . 17 14 Continuity of insulation (nominal conductor diameters up to and including 1,600 mm) 17 14.1 Off-line high voltage continuit

23、y 17 14.2 In-line high voltage continuity 17 15 Temperature index . 17 16 Resistance to refrigerants . 17 17 Solderability . 18 18 Heat or solvent bonding 18 19 Dielectric dissipation factor . 18 20 Resistance to transformer oil 18 21 Loss of mass 18 23 Pin-hole test . 18 30 Packaging 18 Annex A (in

24、formative) Dimensions for intermediate nominal conductor diameter values (R 40) . 19 60317-0-7 IEC:2012 3 Table 1 Dimensions of enamelled wires (R 20) (1 of 2) 11 Table 2 Electrical resistance 13 Table 3 Elongation at break . 13 Table 4 Springiness . 14 Table 5 Mandrel diameters for mandrel winding

25、test 15 Table 6 Heat shock 16 Table 7 Breakdown voltage 17 Table A.1 Dimensions of enamelled wires without a bonding layer (R 40) . 19 4 60317-0-7 IEC:2012 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-7: General requirements Fully insulated

26、(FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The obj

27、ect of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specificati

28、ons (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liais

29、ing with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express

30、, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committee

31、s in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National C

32、ommittees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not p

33、rovide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the

34、latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever,

35、whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications i

36、s indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC

37、 60317-0-7 has been prepared by IEC technical committee 55: Winding wires. The text of this standard is based on the following documents: FDIS Report on Voting 55/1303/FDIS 55/1321/RVD Full information on the voting for the approval of this part can be found in the report on voting indicated in the

38、above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 60317-0-7 IEC:2012 5 This International standard is to be read in conjunction with the IEC 60851 series. The clause numbers used in this part of IEC 60317 are identical with the respective test numbers

39、of the IEC 60851 series. In case of inconsistencies between IEC 60851 and this part of IEC 60317, the latter shall prevail. The numbering of clauses in this standard is not continuous from Clauses 21 and 30 in order to reserve space for possible future wire requirements prior to those for wire packa

40、ging. A list of all the parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on t

41、he IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60317-0-7 IEC:2012 INTRODUCTION This part of IEC 60317 is one of a series which deals with insulat

42、ed wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851 series); 2) Specifications for particular types of winding wires (IEC 60317 series); 3) Packaging of winding wires (IEC 60264 series). 60317-0-7 IEC:2012 7 SPECIFICATI

43、ONS FOR PARTICULAR TYPES OF WINDING WIRES Part 0-7: General requirements Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm 1 Scope This part of IEC 60317 establishes general requirements for fully insulated (FIW) zero-defect enamell

44、ed round copper wires. The nominal conductor diameter range is given in the relevant technical specification. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edi

45、tion cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60172, Test procedure for the determination of the temperature index of enamelled winding wires IEC 60317-0-1:2008, Specifications for particular types of winding wires P

46、art 0-1: General requirements Enamelled round copper wire IEC 60851 (all parts), Winding wires Test methods IEC 60851-5:2008, Winding wires Test methods Part 5: Electrical properties Amendment 1:2011 ISO 3, Preferred numbers Series of preferred numbers 3 Terms, definitions, general notes and appeara

47、nce 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 bonding layer material that is deposited on an enamelled wire and that has the specific function of bonding wires together 3.1.2 class thermal performance of a wire expressed by the temp

48、erature index and the heat shock temperature 8 60317-0-7 IEC:2012 3.1.3 coating material that is deposited on a conductor or wire by suitable means and then dried and/or cured 3.1.4 conductor bare metal after removal of the insulation 3.1.5 crack opening in the insulation that exposes the conductor

49、to view at the stated magnification 3.1.6 dual coating insulation composed of two different materials, an underlying and a superimposed coating 3.1.7 enamelled wire wire coated with an insulation of cured resin 3.1.8 grade of FIW range of overall diameter of a wire Note 1 to entry: This note applies to the French language only. 3.1.9 insulation coating or covering on the conductor with t