IEC 60317-62-2012 Specifications for particular types of winding wires - Part 62 Polyester glass fibre wound minimum class 200 resin or varnish impregnated bare or enamelled rectan.pdf

1、 IEC 60317-62 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types of winding wires Part 62: Polyester glass fibre wound, minimum class 200 resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 Spcifications pour

2、 types particuliers de fils de bobinage Partie 62: Fil de section rectangulaire en cuivre nu ou maill, guip de fibres de verre avec polyester de classe dau moins 200, imprgnes de vernis ou de rsine, dindice de temprature 200 IEC 60317-62:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IE

3、C, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committ

4、ee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indica

5、tion contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez de

6、s questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-12

7、11 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical conten

8、t of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variet

9、y of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on

10、-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International El

11、ectrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) es

12、t la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous poss

13、dez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi de

14、s informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Elec

15、tropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique Inte

16、rnational (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60317-62 Edition 1.0 2012-07 INTERNATIONAL STANDARD NORME INTERNATIONALE Specifications for particular types

17、of winding wires Part 62: Polyester glass fibre wound, minimum class 200 resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 Spcifications pour types particuliers de fils de bobinage Partie 62: Fil de section rectangulaire en cuivre nu ou maill, guip de fib

18、res de verre avec polyester de classe dau moins 200, imprgnes de vernis ou de rsine, dindice de temprature 200 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE K ICS 29.060.10 PRICE CODE CODE PRIX ISBN 978-2-83220-189-3 Registered trademark of the International El

19、ectrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60317-62 IEC:2012 CONTENTS

20、FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms, definitions, general notes and appearance 6 3.1 Terms and definitions 6 3.2 General notes 6 3.2.1 Methods of test 6 3.2.2 Winding wire 7 3.3 Appearance . 7 4 Dimensions 7 5 Electrical resistance . 7 6 Elongation 7 7 Spring

21、iness 7 8 Flexibility and adherence 7 9 Heat shock . 7 10 Cut-through 8 11 Resistance to abrasion . 8 12 Resistance to solvents 8 13 Breakdown voltage . 8 14 Continuity of insulation . 8 15 Temperature index . 8 16 Resistance to refrigerants . 8 17 Solderability . 8 18 Heat or solvent bonding 8 19 D

22、ielectric dissipation factor . 8 20 Resistance to transformer oil 8 23 Pin hole test . 8 30 Packaging 9 Bibliography 10 60317-62 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 62: Polyester glass fibre wound, minimum class 200 resin o

23、r varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is

24、to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and

25、Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the

26、IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly a

27、s possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sen

28、se. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees und

29、ertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any at

30、testation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest editio

31、n of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direc

32、t or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensab

33、le for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60317-62 has

34、 been prepared by IEC technical committee 55: Winding wires. The text of this standard is based on the following documents: FDIS Report on voting 55/1323/FDIS 55/1336/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above tabl

35、e. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 60317-62 IEC:2012 This International standard is to be read in conjunction with the IEC 60317-0-8:2012. The numbering of clauses in this standard is not continuous from Clauses 20 and 30 in order to reserve spa

36、ce for possible future wire requirements prior to those for wire packaging. A list of all the parts in the IEC 60317 series, published under the general title Specifications for particular types of winding wires can be found on the IEC website. The committee has decided that the contents of this pub

37、lication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 60317-62 IEC:2012 5 INTRODUCTI

38、ON This part of IEC 60317 is one of a series which deals with insulated wires used for windings in electrical equipment. The series has three groups describing: 1) Winding wires Test methods (IEC 60851); 2) Specifications for particular types of winding wires (IEC 60317); 3) Packaging of winding wir

39、es (IEC 60264). 6 60317-62 IEC:2012 SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES Part 62: Polyester glass fibre wound, minimum class 200 resin or varnish impregnated, bare or enamelled rectangular copper wire, temperature index 200 1 Scope This part of IEC 60317 specifies the requirements of

40、 polyester glass fibre wound, resin or varnish impregnated, bare or enamelled rectangular copper winding wire, temperature index 200. NOTE For this type of wire, the heat shock test is inappropriate and therefore a heat shock temperature cannot be established. Consequently, a class based on the requ

41、irements for temperature index and heat shock temperature cannot be specified. The range of nominal conductor dimensions covered by this standard is: width: min. 2,0 mm; max. 16,0 mm; thickness: min. 0,80 mm; max. 5,60 mm. The specified combinations of width and thickness as well as the specified wi

42、dth/thickness ratio are according to IEC 60317-0-8. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edi

43、tion of the referenced document (including any amendments) applies. IEC 60317-0-8:2012, Specifications for particular types of winding wires Part 0-8: General requirements Polyester glass fibre wound, resin or varnish impregnated or not impregnated, bare or enamelled rectangular copper wire 3 Terms,

44、 definitions, general notes and appearance 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in 3.1 of IEC 60317-0-8:2012 apply. 3.2 General notes 3.2.1 Methods of test Subclause 3.2 of IEC 60317-0-8:2012 applies. In case of inconsistency between IEC 60317-

45、0-8 and this standard, IEC 60317-62 shall prevail. 60317-62 IEC:2012 7 3.2.2 Winding wire The enamelled wire shall have a temperature index of at least 200 and shall be agreed between purchaser and supplier. The temperature index of the wire is dependent upon the type of impregnating agent used. The

46、 impregnating agent applied to the polyester glass fibre shall contain silicone and have a minimum temperature index of 200. The covering shall have one of the following grades of thickness: PG1: one polyester glass fibre covering over a bare conductor; PG2: two polyester glass fibre coverings over

47、a bare conductor: grade 1 PG1: one polyester glass fibre covering (GL1) over grade 1 enamelled conductor (Grade 1); grade 1 PG2: two polyester glass fibre coverings (GL2) over grade 1 enamelled conductor (Grade 1); grade 2 PG1: one polyester glass fibre covering (GL1) over grade 2 enamelled conducto

48、r (Grade 2); grade 2 PG2: two polyester glass fibre coverings (GL2) over grade 2 enamelled conductor (Grade 2). 3.3 Appearance Subclause 3.3 of IEC 60317-0-8:2012 applies. 4 Dimensions Clause 4 of IEC 60317-0-8:2012 applies. 5 Electrical resistance Clause 5 of IEC 60317-0-8:2012 applies. 6 Elongatio

49、n Clause 6 of IEC 60317-0-8:2012 applies. 7 Springiness Clause 7 of IEC 60317-0-8:2012 applies. 8 Flexibility and adherence Clause 8 of IEC 60317-0-8:2012 applies. 9 Heat shock Test inappropriate. 8 60317-62 IEC:2012 10 Cut-through Test inappropriate. 11 Resistance to abrasion Test inappropriate. 12 Resistance to solvents Test inappropriate. 13 Breakdown voltage Clause 13 of IEC 60317-0-8:2012 applies. 14