IEC 60763-2-2007 Specification for laminated pressboard - Part 2 Methods of test《层压纸板的规范.第2部分 试验方法》.pdf

1、 IEC 60763-2 Edition 2.0 2007-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Specification for laminated pressboard Part 2: Methods of test Spcification pour cartons comprims et contrecolls Partie 2: Mthodes dessai IEC 60763-2:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva,

2、Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the c

3、ountry of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contra

4、ire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions

5、 sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.ie

6、c.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under consta

7、nt review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,)

8、 It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.ele

9、ctropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: w

10、ww.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale

11、CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que v

12、ous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,).

13、 Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et au

14、ssi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Ele

15、ctrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +

16、41 22 919 03 00 IEC 60763-2 Edition 2.0 2007-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Specification for laminated pressboard Part 2: Methods of test Spcification pour cartons comprims et contrecolls Partie 2: Mthodes dessai INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE

17、INTERNATIONALE R ICS 17.220.99; 29.035.10 PRICE CODE CODE PRIX ISBN 2-8318-1045-6 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 60763-2 IEC:2007 CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references

18、 .7 3 Conditioning of test specimens.8 4 Drying of test specimens 8 4.1 Method A (preferable) .8 4.2 Method B.8 5 Dimensions 8 5.1 Thickness8 6 Mechanical tests.9 6.1 Flexural strength and load to produce a standard deflection 9 6.2 Apparent modulus of elasticity in flexure .10 7 Compressibility.10

19、7.1 Principle10 7.2 Test apparatus 11 7.3 Test pieces11 7.4 Procedure .11 7.5 Results11 8 Electric strength in oil.12 8.1 General and conditioning.12 8.2 Electric strength along laminate (edgewise electric strength).12 9 Internal ply strength, thermal resistance and oil compatibility .12 9.1 Princip

20、le12 9.2 Test specimens .12 9.3 Test apparatus 13 9.4 Procedure .13 9.5 Determination of the flexural strength13 9.6 Results13 10 Apparent density 14 10.1 Test specimens .14 10.2 Procedure .14 10.3 Results14 11 Moisture content.15 12 Shrinkage in air after drying15 12.1 Test specimens .15 12.2 Proce

21、dure .15 12.3 Results15 13 Oil absorption.15 13.1 Test specimens .15 13.2 Procedure .15 13.3 Results16 14 Ash content 16 14.1 Procedure .16 14.2 Results16 60763-2 IEC:2007 3 15 Contamination of liquid dielectrics 16 15.1 Apparatus16 15.2 Test specimens .16 15.3 Procedure .17 15.4 Results17 16 Conduc

22、tivity of aqueous extract17 16.1 Procedure .17 16.2 Results17 17 pH of aqueous extract 17 Figure 1 Position of test specimen in relation to length, width and thickness of sheet 17 Figure 2 Size of the test specimens and arrangement of the electrodes for testing the electric strength along laminae (e

23、dgewise electric strength)18 Figures 3 and 4 Alternative forms of vented electrodes 19 Table 1 Number of test specimens.13 4 60763-2 IEC:2007 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SPECIFICATION FOR LAMINATED PRESSBOARD Part 2: Methods of test FOREWORD 1) The International Electrotechnical Comm

24、ission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and

25、in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee

26、interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accorda

27、nce with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all inter

28、ested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsi

29、ble for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence b

30、etween any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All

31、users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or

32、other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publicatio

33、n. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such pa

34、tent rights. International Standard IEC 60763-2 has been prepared by IEC technical committee 15: Solid electrical insulating materials. This second edition cancels and replaces the first edition published in 1991 and constitutes a technical revision. This edition includes the following significant t

35、echnical changes with respect to the previous edition. a) The standard has generally been revised editorially and brought into line with IEC 60641-2. b) The test method for the determination of the internal ply strength has been replaced with an alternative method. c) The test method for the determi

36、nation of the thermal resistance has been enlarged in its scope. 60763-2 IEC:2007 5 This bilingual version, published in 2009-06, corresponds to the English version. The text of this standard is based on the following documents: FDIS Report on voting 15/360/FDIS 15/373/RVD Full information on the vo

37、ting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. The list of all parts of the IEC 60763 series, under the general title Specification for laminated pressboard, can be found on the IE

38、C website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn

39、 replaced by a revised edition, or amended. 6 60763-2 IEC:2007 INTRODUCTION This International Standard deals with laminated pressboard as defined in Clause 2 of IEC 60763-1. IEC 60641 applies to pressboard which is not laminated, and the material covered by this International Standard is made from

40、 sheets conforming to the requirements of that publication. 60763-2 IEC:2007 7 SPECIFICATION FOR LAMINATED PRESSBOARD Part 2: Methods of test 1 Scope This part of IEC 60763 gives methods of test applicable for the material classified in IEC 60763-1. 2 Normative references The following referenced do

41、cuments are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60243-1:1998, Electrical strength of insulating materials Test methods P

42、art 1: Tests at power frequencies IEC 60247:2004, Insulating liquids Measurement of relative permittivity, dielectric dissipation factor (tan ) and d.c. resistivity IEC 60250:1969, Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulatin

43、g materials at power, audio and radio frequencies including metre wavelengths. IEC 60296:2003, Fluids for electrotechnical applications Unused mineral insulating oils for transformers and switchgear IEC 60641-2:2004, Pressboard and presspaper for electrical purposes Part 2: Methods of tests IEC 6076

44、3-1:1983, Specification for laminated pressboard Part 1: Definitions, classification and general requirements IEC 61125:1992, Unused hydrocarbon-based insulating liquids Test methods for evaluating the oxidation stability IEC 62021-1:2003, Insulating liquids Determination of acidity Part 1: Automati

45、c potentiometric titration ISO 287:1985, Paper and board Determination of moisture content Oven-drying method ISO 2144:1997, Paper, board and pulps Determination of residue (ash) on ignition at 900 degrees C 8 60763-2 IEC:2007 3 Conditioning of test specimens Since the conditioning of laminated pres

46、sboard is very time-consuming, the material is tested either as received or dried. Only in case of dispute shall the material be conditioned according to the following procedure. The conditioning shall be made at 23 C 2 K and (50 5) % relative humidity until the moisture content of the specimen reac

47、hes 5,5 % to 8 %. The conditioning shall be approached from the dry side after drying at 70 C 5 K for a period sufficient to ensure that the conditioning atmosphere produces a mass increase in the specimen. 4 Drying of test specimens 4.1 Method A (preferable) The test specimens shall be dried at 105

48、 C 2 K for (24 1) h in an oven with forced air circulation and subsequently at 105 C 2 K for (48 2) h in a vacuum chamber at a residual pressure of not more than 1 kPa. The specimens shall then be removed and allowed to cool in a desiccator before the test. 4.2 Method B Test specimens shall be dried

49、 in a ventilated oven at 105 C 2 K for (168 8) h at atmospheric pressure. When test pieces of the specified size are dried according to method B, test results similar to the test results obtained after drying according to method A may be expected. 5 Dimensions 5.1 Thickness 5.1.1 Test apparatus An external screw-type micrometer having measuring faces of 6 mm to