1、 IEC 60917-2-4Edition 1.0 2010-03INTERNATIONAL STANDARD NORME INTERNATIONALEModular order for the development of mechanical structures for electronic equipment practices Part 2-4: Sectional specification Interface co-ordination dimensions for the 25 mm equipment practice Adaptation dimensions for su
2、bracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in) Ordre modulaire pour le dveloppement des structures mcaniques pour les infrastructures lectroniques Partie 2-4: Spcification intermdiaire Dimensions de coordination pour les interfaces des infrastructures au
3、 pas de 25 mm Dimensions dadaptation des bacs ou des chssis, applicables dans les baies ou les btis, conformment la CEI 60297-3-100 (19 pouces) IEC60917-2-4:2010 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specifie
4、d, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about I
5、EC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reprod
6、uite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des
7、droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Comm
8、ission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the l
9、atest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and rep
10、laced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of elec
11、tronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your fe
12、edback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et p
13、ublie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amen
14、dement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les pu
15、blications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premi
16、er dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www
17、.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60917-2-4Edition 1.0 2010-03INTERNATIO
18、NAL STANDARD NORME INTERNATIONALEModular order for the development of mechanical structures for electronic equipment practices Part 2-4: Sectional specification Interface co-ordination dimensions for the 25 mm equipment practice Adaptation dimensions for subracks or chassis applicable in cabinets or
19、 racks in accordance with IEC 60297-3-100 (19 in) Ordre modulaire pour le dveloppement des structures mcaniques pour les infrastructures lectroniques Partie 2-4: Spcification intermdiaire Dimensions de coordination pour les interfaces des infrastructures au pas de 25 mm Dimensions dadaptation des ba
20、cs ou des chssis, applicables dans les baies ou les btis, conformment la CEI 60297-3-100 (19 pouces) INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE NICS 31.240 PRICE CODECODE PRIXISBN 2-8318-1084-0 Registered trademark of the International Electrotechnical Commi
21、ssion Marque dpose de la Commission Electrotechnique Internationale colourinside 2 60917-2-4 IEC:2010 CONTENTS FOREWORD.3 INTRODUCTION.5 1 Scope and object6 2 Normative references .6 3 Arrangement overview (Figure 1) and definitions 7 4 Dimensions for adaptor flanges of the specific metric subracks
22、or chassis (suitable only where WS1= 425 mm) mountable into 19 in cabinets or racks.8 4.1 General .8 4.2 Dimensions for mounting holes arrangements on the adaptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or chassis8 4.3 Dimensions for mounting holes arrangem
23、ents on the adaptor flanges, mounting layout referred to the unit centre lines of the metric subracks or chassis10 Bibliography14 Figure 1 Arrangement overview Adaptation of specific subracks (aperture width for plug-in units: WS1= 425 mm, 85 5,0 mm) of IEC 60917-2-4 into cabinets of IEC 60297-3-100
24、 7 Figure 2 Mounting hole arrangements of the adaptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or chassis.8 Figure 3 Dimensions of mounting hole positions of the adaptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or ch
25、assis 9 Figure 4 Mounting hole arrangements on the adaptor flanges, mounting layout referred to the unit centre lines of the metric subracks or chassis .11 Figure 5 Dimensions of mounting holes positions of the adaptor flanges, mounting layout referred to the unit centre lines of the metric subracks
26、 or chassis.12 Table 1 Dimensions of mounting holes positions of the adaptor flanges, mounting layout referred to the bottom pitch lines of the metric subracks or chassis 10 Table 2 Dimensions of mounting holes positions of the adaptor flange, mounting layout referred to the unit centre lines of the
27、 metric subracks or chassis.13 60917-2-4 IEC:2010 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRACTICES Part 2-4: Sectional specification Interface co-ordination dimensions for the 25 mm equipment practice Adaptati
28、on dimensions for subracks or chassis applicable in cabinets or racks in accordance with IEC 60297-3-100 (19 in) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committee
29、s). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available
30、Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organiza
31、tions liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matt
32、ers express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC Nationa
33、l Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC
34、 National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself
35、 does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that the
36、y have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature w
37、hatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced pub
38、lications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International S
39、tandard IEC 60917-2-4 has been prepared by subcommittee 48D: Mechanical structures for electronic equipment, of IEC technical committee 48: Electromechanical components and mechanical structures for electronic equipment. 4 60917-2-4 IEC:2010 The text of this standard is based on the following docume
40、nts: FDIS Report on voting 48D/420/FDIS 48D/424/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. A list of all parts of IEC 60917 series, under the general title Modular order for the development of mechanical str
41、uctures for electronic equipment practices, can be found on the IEC website. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability indicated on the IEC web site un
42、der “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are co
43、nsidered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 60917-2-4 IEC:2010 5 INTRODUCTION The IEC 60917 series of standards provides definitions of mechanical structure and dimensions for metric cabinets, racks, subracks
44、, chassis and plug-in units based on metric modular ordered dimensions. The later developed IEC 60917 series of standards, compared to IEC 60297, provides more logical design practices based on metric dimensioning. The IEC 60297 series of standards also define structures and interface dimensions for
45、 19 in cabinets, racks and their compatible subracks and chassis. Because of the longer history of the IEC 60297 series of standards and their applications, the combination of 19 in based cabinets, racks, subracks and chassis are broadly applied for all industrial electronic fields in the world. Req
46、uests for combined applications with both mechanical structures, the IEC 60917 series (metric standard) and the IEC 60297 series (19 in standard), resulted in requirements to mount metric subracks or chassis into 19 in standard cabinets or racks and, vice versa, 19 in subracks or chassis into metric
47、 cabinets or racks. To cope with the requirements and needs, it is required to develop definitions for appropriate adaptation dimensions of flanges for metric or 19 in subracks or chassis to mount them into cabinets or racks in accordance with 19 in or metric standard. And the definitions of adaptat
48、ion dimensions bring economical solutions for installations of electronic equipment into existing cabinets or racks. Further, they provide guidance to electro-mechanical designers to develop systems suitable to be mounted into both IEC standard series flexibly. To meet such market needs, this standa
49、rd defines adaptation dimensions for metric subracks or chassis applicable for 19 in cabinets or racks. (Dimensions for the applications, where 19 in subracks or chassis are mounted on metric cabinets or racks, are defined in a separate standard, i.e. IEC 60297-3-106.) 6 60917-2-4 IEC:2010 MODULAR ORDER FOR THE DEVELOPMENT OF MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT PRAC
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1