IEC 60939-2-1-2004 Complete filter units for radio interference suppression - Part 2-1 Blank detail specification - Passive filter units for electromagnetic interference suppressio.pdf

1、 INTERNATIONAL STANDARD IEC 60939-2-1First edition 2004-11Complete filter units for radio interference suppression Part 2-1: Blank detail specification Passive filter units for electromagnetic interference suppression Filters for which safety tests are required (assessment level D/DZ) Reference numb

2、er IEC 60939-2-1:2004(E) Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For exampl

3、e, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review

4、by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under considerat

5、ion and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpu

6、b) enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issu

7、ed publications (www.iec.ch/online_news/ justpub) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service C

8、entre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IEC 60939-2-1First edition 2004-11Complete filter units for radio interference suppression Part 2-1: Blank detail specification Passive filter units for electromagnetic interference suppression Filters fo

9、r which safety tests are required (assessment level D/DZ) IEC 2004 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher.

10、International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch P For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International El

11、ectrotechnical Commission 2 60939-2-1 IEC:2004(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ COMPLETE FILTER UNITS FOR RADIO INTERFERENCE SUPPRESSION Part 2-1: Blank detail specification Passive filter units for electromagnetic interference suppression Filters for which safety tests are required (a

12、ssessment level D/DZ) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning

13、standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their prep

14、aration is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

15、 with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant

16、subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the techn

17、ical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum exte

18、nt possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for an

19、y equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees

20、 and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8

21、) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rig

22、hts. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60939-2-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. The text of this standard is based on the following documents: FDIS Report on

23、 voting 40/1466/FDIS 40/1487/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 60939-2-1 IEC:2004(E) 3 IEC 60939 consists of the

24、following parts under the general title Complete filter units for radio interference suppression: Part 1: Generic specification Part 2: Sectional specification The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC

25、 web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this standard may be issued at a later date. 4 60939-2-1 IEC:2004(E) INTRODUCTION B

26、lank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style and layout and minimum content of detail specifications. In the preparation of detail specifications, the content of 1.4 of the sectional specificatio

27、n shall be taken into account. The use of IEC 60939-2-2 may be more appropriate for components where approval and requalification tests contribute considerably to the cost of the product, whereas the employment of this specification may be necessary for components manufactured in mass production. Th

28、is specification offers the assessment levels D and DZ (Zero defect). Identification of the detail specification and of the component The first page of the detail specification should have the layout recommended on the next page of this blank detail specification. The numbers between square brackets

29、 correspond to the following information which shall be inserted at the position indicated: 1 The name of the National Standards Organization under whose authority the detail specification is published and, if applicable, the organization from which the detail specification is available. 2 The IECQ

30、symbol and the number allotted to the detail specification by the IECQ General Secretariat. 3 The number and issue number of the IECQ generic or sectional specification as relevant; also national reference if different. 4 If different from the IECQ number, the national number of the detail specifica

31、tion, date of issue and any further information required by the national system, together with any amendment numbers. 5 A brief description of the component or range of components. 6 Information on typical construction (when applicable). For 5 and 6 the text to be given in the detail specification s

32、hould be suitable for an entry in the IECQ Register of Approvals. 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the appropriate national or international documents for outlines. Alternatively the drawing may be given in an annex to the deta

33、il specification, but 7 should always contain an illustration of the general outer appearance of the component. 8 The level(s) of quality assessment covered by the detail specification, as appropriate. 9 Reference data giving information on the most important properties of the component which allow

34、comparison between the various component types intended for the same or similar applications. 60939-2-1 IEC:2004(E) 5 1 IEC 60939-2-1-XXX 2 QC XXXXXXXXX ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH: IEC 60939-1 IEC 60939-2 3 4 Outline and dimensions: ( . angle projection) PASSIVE FIL

35、TER UNITS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION AND FOR CONNECTION TO THE SUPPLY MAINS FILTERS FOR WHICH SAFETY TESTS ARE REQUIRED 5 7 TYPICAL CONSTRUCTION: cylindrical/rectangular non-metallic/metallic case insulated/non-insulated axial/radial/screwed terminations contains capacitors of subc

36、lasses X and Y 6 (Other shapes are permitted within the dimensions given, see Table 1) 8 Assessment level D / DZ NOTE For 1 to 9, see preceding page. REFERENCE DATA: Rated voltages, current range, climatic category, frequency range, insertion loss range, functional circuit diagram. 9 Information on

37、the availability of components qualified to this detail specification is given in the IEC QC 001005. 6 60939-2-1 IEC:2004(E) COMPLETE FILTER UNITS FOR RADIO INTERFERENCE SUPPRESSION Part 2-1: Blank detail specification Passive filter units for electromagnetic interference suppression Filters for whi

38、ch safety tests are required (assessment level D/DZ) 1 General data 1.1 Method of mounting for vibration, bump and shock tests See 1.3.2 of IEC 60939-2. 1.2 Dimensions Table 1 Dimensions related to case size Case size reference Dimensions mm L W H . . . . . When there is no case size reference, Tabl

39、e 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Table 1. The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 1.3 Ratings and characteristics Rated voltages (see Table 2a) Category voltage (if applicable) (see Table 2a) Ra

40、ted current (see Table 2b) DC line resistance or d.c. voltage drop at rated current Maximum current at upper category temperature and derating curve (if applicable) Maximum internal and external temperatures for temperature rise test (if applicable) Climatic category Rated temperature Insertion loss

41、, no load/room temperature (see Table 2a) Insertion loss, load/temperature (see Table 2b) Insulation resistance Discharge resistance (if applicable) Category of passive flammability (if applicable) 60939-2-1 IEC:2004(E) 7 Table 2a Insertion loss at no load Case size or type designation Rated voltage

42、 Category voltage Minimum insertion loss dB kHz kHz MHz MHz MHz GHz GHz Table 2b Insertion loss at specified current and temperature Case size or type designation Rated current Test current Test temp. C Minimum insertion loss dB kHz kHz MHz MHz MHz GHz GHz 1.4 Normative references IEC 60384-1, Fixed

43、 capacitors for use in electronic equipment Part 1: Generic specification IEC 60410, Sampling plans and procedures for inspection by attributes IEC 60939-1, Complete filter units for radio interference suppression Part 1: Generic specification 1IEC 60939-2, Complete filter units for radio interferen

44、ce suppression Part 2: Sectional specification 21.5 Marking The marking of the filter, if any, and the packing shall be in accordance with 1.5 of IEC 60939-2. The details of the marking of the filter and the packing shall be given in full in the detail specification. _ 1To be published. 8 60939-2-1

45、IEC:2004(E) 1.6 Ordering information Orders for filters covered by this specification shall contain, in clear or in coded form, the following information: (a) type designation; (b) rated voltage; (c) number and issue reference of this detail specification. 1.7 Certified test records Required/not req

46、uired. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTE Additional or increased requirements should be specified only when essential. Table 3 Other characteristics Thi

47、s table is to be used for defining characteristics which are additional to or more severe than those given in the sectional specification 2 Inspection requirements 2.1 Procedures 2.1.1 For Qualification Approval the procedures shall be in accordance with 3.4.2 of IEC 60939-2. 2.1.2 For Quality Confo

48、rmance inspection the test schedule (Table 4) includes sampling, periodicity, severities and requirements. The formation of inspection lots is covered by 3.5.1 of IEC 60939-2. 60939-2-1 IEC:2004(E) 9 Table 4a Test schedule for lot-by-lot tests (Group A and Group B inspection) Assessment level D / DZ

49、 Assessment level D IL AQL Clause number and test 1) Conditions of test 1) 2) Performance requirements 1)Group A1 Non-destructive S-4 2,5 % 4.2 Visual examination As in 4.2 4.2 Marking Any marking on the filter shall be legible and correct 4.2 Dimensions (gauging) See Table 1 of this specification Group A2 Non-destructive II 1,0 % 4.5 DC line resistance or volta