IEC 60966-3-1-2009 Radio frequency and coaxial cable assemblies - Part 3-1 Blank detail specification for semi-flexible coaxial cable assemblies《射频和同轴电缆组件.第3-1部分 半柔软同轴电缆组件用空白详细规范》.pdf

1、 IEC 60966-3-1 Edition 3.0 2009-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio frequency and coaxial cable assemblies Part 3-1: Blank detail specification for semi-flexible coaxial cable assemblies Cordons coaxiaux et cordons pour frquences radiolectriques Partie 3-1: Spcification particulire-

2、cadre relative aux cordons coaxiaux semi- flexibles IEC 60966-3-1:2009-01(EN-FR) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by

3、any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publi

4、cation, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique

5、ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou conta

6、ctez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that pre

7、pares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have b

8、een published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publicat

9、ions search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to d

10、ate on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in Eng

11、lish and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause

12、of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service

13、 Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu tec

14、hnique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes inte

15、rnationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfre

16、nce, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne e

17、t aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vo

18、cabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extrait

19、es des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60966-3-1 Edition 3.0 2009-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio

20、 frequency and coaxial cable assemblies Part 3-1: Blank detail specification for semi-flexible coaxial cable assemblies Cordons coaxiaux et cordons pour frquences radiolectriques Partie 3-1: Spcification particulire-cadre relative aux cordons coaxiaux semi- flexibles INTERNATIONAL ELECTROTECHNICAL C

21、OMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE K ICS 33.120.10 PRICE CODE CODE PRIX ISBN 978-2-8322-1354-4 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication f

22、rom an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. colour inside 2 60966-3-1 IEC:2009 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO FREQUENCY AND COAXIAL CABLE ASSEMBLIES Part 3-1: Blank detail specification for semi-fl

23、exible coaxial cable assemblies FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions c

24、oncerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”).

25、Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborat

26、es closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the

27、 relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that

28、 the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the ma

29、ximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsi

30、ble for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical

31、committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publi

32、cations. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

33、patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60966-3-1 has been prepared by IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. This bilingual vers

34、ion (2014-01) corresponds to the monolingual English version, published in 2009-01. This third edition cancels and replaces the second edition published in 2003 and constitutes a technical revision. The major change with respect to the first edition is the reference to the third edition of the secti

35、onal specification. This blank detail specification is to be read in conjunction with the second edition of IEC 60966-1 (1999) and with the third edition of IEC 60966-3 (2008). 60966-3-1 IEC:2009 3 The text of this standard is based on the following documents: FDIS Report on voting 46/306/FDIS 46/31

36、8/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all pa

37、rts of the IEC 60966 series, under the general title: Radio frequency and coaxial cable assemblies, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webs

38、tore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be

39、useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 4 60966-3-1 IEC:2009 INTRODUCTION This part of IEC 60966 is a blank detail specification that relates to semi-flexible coaxial cable assemblies operating in the transverse electro

40、magnetic mode (TEM). The creation of a uniform layout and style of a detail specification is determined by the use of a blank detail specification pro forma. The detail specification may be prepared by the insertion of data into the pro forma by a national standards organization, by an approved manu

41、facturer or by a user (when prepared by a user, the detail specification shall be submitted to the national authorized institution by an approved manufacturer). Instructions to complete a blank detail specification: Detail specifications should, as far as possible, be written in accordance with the

42、pro forma which has: a front page with a general description and a drawing or isometric sketch of the cable assembly and its possible variants; ratings, characteristics and inspection requirements (those which are not required or specified shall be omitted). Under quality assessment, tests are divid

43、ed into groups. Whenever possible, entire groups are either specified or omitted. These groups are: Ba (basic) Visual and dimensional tests Eb (electrical basic) Low-frequency operational tests Eh (electrical high frequency) High-frequency tests Ep (electrical phase) Electrical length tests Ee (elec

44、trical screening effectiveness) Screening effectiveness tests Ez (electrical impedance Z) Impedance uniformity tests Et (electrical transmission) Power rating test Mn (mechanical) Mechanical tests Vc (environmental climatic) Climatic tests Vv (environmental vibration) Vibration, bumps and shock test

45、s Vt (environmental temperature) Humidity, rapid change of temperature and chemical tests Vf (environmental flammability) Flammability, dust and water immersion tests 60966-3-1 IEC:2009 5 The numbers shown in brackets on this page correspond to the following items of required information, which shou

46、ld be entered in the spaces provided. 1 Name and address of the organization that has prepared the document. 2 IEC document number, issue number and date of issue. 3 Address of the organization from which the document is available. 4 Related documents. 5 Any other reference to the cable assembly, na

47、tional reference, trade name, etc. 6 A drawing of the cable assembly giving the outline and principal dimensions. The dimensions are considered to be in millimetres unless otherwise specified. NOTE The symbol “l“ may be used to specify the cable length. In this case, the detail specification covers

48、cable assemblies of any length and “l“ should then be specified in the order. 7 Nominal characteristic impedance of the cable assembly. 8 Frequency range of use of the cable assembly (DC may be used as a lower limit of frequency, indicating that the cable assembly is capable of transmitting d.c., bu

49、t at d.c. a number of characteristics may neither apply nor be verified by inspection.) 9 Weight, function of the length of the cable assembly. 10 Minimum static inside bending radius of the cable assembly. Also minimum dynamic inside bending radius of the cable assembly, i.e. the bending radius used for the insertion loss and stability of electrical length tests. 11 Climatic category of the cable assembly related