IEC 61169-11-2017 Radio-frequency connectors - Part 11 Sectional specification for RF coaxial connectors with inner diameter of outer conductor 9 5 mm with threaded coupling - Char.pdf

1、 IEC 61169-11 Edition 1.0 2017-03 INTERNATIONAL STANDARD Radio-frequency connectors Part 11: Sectional specification for RF coaxial connectors with inner diameter of outer conductor 9,5 mm with threaded coupling Characteristic impedance 50 (type 4,1-9,5) IEC 61169-11:2017-03(en) colour inside THIS P

2、UBLICATION IS COPYRIGHT PROTECTED Copyright 2017 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writ

3、ing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further info

4、rmation. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for a

5、ll electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/ca

6、talogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced s

7、earch enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published d

8、etails all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 16 additional lan

9、guages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collect

10、ed from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 61169-11 Edition 1.0 2017-03 INTERNATIONAL ST

11、ANDARD Radio-frequency connectors Part 11: Sectional specification for RF coaxial connectors with inner diameter of outer conductor 9,5 mm with threaded coupling Characteristic impedance 50 (type 4,1-9,5) INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.120.30 ISBN 978-2-8322-4129-5 Registered trade

12、mark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. colour inside 2 IEC 61169-11:2017 IEC 2017 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references 6 3 Mating face and gauge information 6 Dimensions General con

13、nectors Grade 2 6 3.1 3.1.1 Connector with pin centre contact 6 3.1.2 Connector with socket centre contact 8 Gauges . 9 3.2 3.2.1 Gauge pin for socket centre contact. 9 3.2.2 Connector with pin centre contact 10 Dimensions Standard test connectors Grade 0 10 3.3 3.3.1 Connector with pin centre conta

14、ct 10 3.3.2 Connector with socket centre contact 11 4 Quality assessment procedures . 12 General . 12 4.1Ratings and characteristics (see Clause 5 of IEC 61169-1:2013) 12 4.2Test schedule and inspection requirements. 15 4.3 4.3.1 Acceptance tests . 15 4.3.2 Periodic tests . 15 Procedures for the qua

15、lity conformance 18 4.4 4.4.1 Quality conformance inspection . 18 4.4.2 Qualification approval and its maintenance 18 5 Instructions for preparation of detail specifications 18 General . 18 5.1Identification of the component . 18 5.2Performances . 18 5.3Marking, ordering information and related matt

16、ers 19 5.4Selection of tests, test conditions and severities . 19 5.5Blank detail specification pro-forma for type 4,1-9,5 connector 19 5.6 6 Marking . 23 Marking of component . 23 6.1Marking and contents of package 24 6.2Figure 1 Connector with pin centre contact (for dimensions, see Table 1) 7 Fig

17、ure 2 Connector with socket centre contact (for dimensions, see Table 2) . 8 Figure 3 Gauge pin for socket centre contact (for dimensions, see Table 3) . 9 Figure 4 Connector with pin centre contact (for dimensions, see Table 4) 11 Figure 5 Connector with socket in centre contact (for dimensions, se

18、e Table 5) . 11 Table 1 Dimensions of connector with pin centre contact . 7 Table 2 Dimensions of connector with socket centre contact 9 Table 3 Dimensions of gauge pin for socket centre contact 10 Table 4 Dimensions of connector with pin centre contact . 11 Table 5 Dimensions of connector with sock

19、et centre contact 12 IEC 61169-11:2017 IEC 2017 3 Table 6 Rating and characteristics . 13 Table 7 Acceptance tests . 16 Table 8 Periodic tests 17 4 IEC 61169-11:2017 IEC 2017 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNECTORS Part 11: Sectional specification for RF coaxial connec

20、tors with inner diameter of outer conductor 9,5 mm with threaded coupling Characteristic impedance 50 (type 4,1-9,5) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Commi

21、ttees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Availa

22、ble Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental org

23、anizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical

24、 matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC Na

25、tional Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity

26、, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC i

27、tself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure tha

28、t they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nat

29、ure whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the reference

30、d publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Internatio

31、nal Standard IEC 61169-11 has been prepared by subcommittee 46F: RF and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, RF and microwave passive components and accessories. The text of this International Standard is based on the following docume

32、nts: CDV Report on voting 46F/322A/CDV 46F/336/RVC Full information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. IEC 61169-11:2017 IEC

33、 2017 5 A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors, can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.ie

34、c.ch“ in the data related to the specific document. At this date, the document will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indi

35、cates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 6 IEC 61169-11:2017 IEC 2017 RADIO-FREQUENCY CONNECTORS Part 11: Sectional specification for RF coaxial connectors with i

36、nner diameter of outer conductor 9,5 mm with threaded coupling Characteristic impedance 50 (type 4,1-9,5) 1 Scope This part of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for RF coaxial connectors with threaded

37、coupling, typically for use in 50 cable networks (type 4,1-9,5). This document prescribes mating face dimensions for general purpose connectors grade 2, dimensional details of standard test connectors-grade 0, gauging information and tests selected from IEC 61169-1, applicable to all detail specific

38、ations relating to series 4,1-9,5 RF connectors. This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test schedules and inspection requirements for assessment levels M and H. The 4,1-9,5 types RF coaxial connectors w

39、ith nominal impedance 50 are threaded coupling units which are used with all kinds of RF cables and microstrips in microwave transmission systems. And the working frequency is up to 14 GHz. NOTE Metric dimension are original dimensions. All undimensioned pictorial configurations are for reference pu

40、rpose only. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includi

41、ng any amendments) applies. IEC 61169-1:2013, Radio frequency connectors Part 1: Generic specification General requirements and measuring methods IEC 62037-3, Passive RF and microwave devices, intermodulation level measurement Part 3: Measurement of passive intermodulation in coaxial connectors 3 Ma

42、ting face and gauge information Dimensions General connectors Grade 2 3.1 3.1.1 Connector with pin centre contact The mating face of connector with pin centre contact is shown in Figure 1 and its dimensions are shown in Table 1. IEC 61169-11:2017 IEC 2017 7 NOTE 1 Mechanical and electrical reference

43、 plane. NOTE 2 “M201“ indicates metric screw thread with nominal diameter 20 mm and screw-pitch of 1 mm. Figure 1 Connector with pin centre contact (for dimensions, see Table 1) Table 1 Dimensions of connector with pin centre contact Ref. mm Min. Max. a M201 b 11,84 12,02 c 2,855 2,945 da4,13 (nomin

44、al) e 9,45 9,55 f 5,05 5,35 g 1,4 1,6 h 0 1,0 i 3,0 4,0 j b k c l 6,2 m 10,8 a This dimension tolerance is determined by the tolerance of characteristic impedance. b Sealing gasket to meet climatic and environmental requirements. c The dimension given assumes no sealing gasket fitted. If sealing is

45、required, dimension k (Figure 1) should be arranged so that with the gasket chosen adequate pressure is applied to the front face (dimensions m and b) of the socket connector (Figure 2) to ensure adequate sealing. IEC 50 5 i g f Note 2 Note 1 b a m e d c j h l k 8 IEC 61169-11:2017 IEC 2017 3.1.2 Co

46、nnector with socket centre contact The mating face of connector with socket centre contact is shown in Figure 2 and its dimensions are shown in Table 2. NOTE 1 Mechanical and electrical reference plane. NOTE 2 “M201” indicates metric screw thread with nominal diameter 20 mm and screw-pitch of 1 mm.

47、NOTE 3 Minimum distance from installation flanges or accessories. NOTE 4 Design for undercut to be allowed. Figure 2 Connector with socket centre contact (for dimensions, see Table 2) IEC 45 5 i f Note 4 Note 1 b a m e d c h l k 45 Note 2 n j Note 3 IEC 61169-11:2017 IEC 2017 9 Table 2 Dimensions of

48、 connector with socket centre contact Ref. mm Min. Max. a M201 b 12,03 12,21 c a d b4,13 (nominal) e 9,45 9,55 f 4,73 5,03 h 6,5 i 5 j 1,9 2,3 k 6,05 6,20 l 6 m 14,9 15,0 n 18,3 18.4 a Slot design optional. When mating with a pin with 2,855 mm to 2,945 mm, it shall meet the mechanical and electrical

49、 requirements. bThis dimension tolerance is determined by the tolerance of characteristic impedance. Gauges 3.2 3.2.1 Gauge pin for socket centre contact The gauge pin for socket centre contact is shown in Figure 3 and its dimensions are shown in Table 3. Figure 3 Gauge pin for socket centre contact (for dimensions, see Table 3) IEC 50 5 a b c R0,2 max. 0,4