1、 IEC 61196-11-1 Edition 1.0 2016-01 INTERNATIONAL STANDARD Coaxial communication cables Part 11-1: Blank detail specification for semi-rigid cables with polyethylene (PE) dielectric IEC 61196-11-1:2016-01(en) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2016 IEC, Geneva, Switzerland All rights
2、reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester
3、. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 0
4、3 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The techni
5、cal content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical informa
6、tion on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, te
7、xt, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email
8、. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC
9、 Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Cen
10、tre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 61196-11-1 Edition 1.0 2016-01 INTERNATIONAL STANDARD Coaxial communication cables Part 11-1: Blank detail specification for semi-
11、rigid cables with polyethylene (PE) dielectric INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.120.10 ISBN 978-2-8322-3090-9 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. 2 IEC 61196-11-1:2
12、016 IEC 2016 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Guidance for the preparation of detail specifications 5 4 Blank detail specification . 6 IEC 61196-11-1:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ COAXIAL COMMUNICATION CABLES Part 11-1: Blank detail specificati
13、on for semi-rigid cables with polyethylene (PE) dielectric FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-o
14、peration on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to
15、 as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this
16、preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
17、consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable effo
18、rts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publicati
19、ons transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Inde
20、pendent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No
21、liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (
22、including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct applicatio
23、n of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61196-11-1 has been prepared by subcommit
24、tee 46A: Coaxial cables, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. The text of this standard is based on the following documents: FDIS Report on voting 46A/1281/FDIS 46A/1292/RVD Full information on the voting fo
25、r the approval of this standard can be found in the report on voting indicated in the above table. A list of all parts in the IEC 61196 series, under the general title: Coaxial communication cables, can be found on the IEC website. 4 IEC 61196-11-1:2016 IEC 2016 This part of IEC 61196 should be read
26、 in conjunction with IEC 61196-1:2005 and IEC 61196-11:2016. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/w
27、ebstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IEC 61196-11-1:2016 IEC 2016 5 COAXIAL COMMUNICATION CABLES
28、 Part 11-1: Blank detail specification for semi-rigid cables with polyethylene (PE) dielectric 1 Scope This part of IEC 61196 applies to semi-rigid coaxial communication cables with polyethylene (PE) dielectric and tubular outer conductor. These cables are intended for use in microwave and wireless
29、equipments or other signal transmission equipments or units at frequencies above 500 MHz. This part of IEC 61196 determines the layout and style for detail specification. Detail specifications, based on the blank detail specification, may be prepared by a national organization, a manufacturer, or a
30、user. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any
31、 amendments) applies. IEC 61196-1:2005, Coaxial communication cables Part 1: Generic specification General, definitions and requirements IEC 61196-11:2016, Coaxial communication cables Part 11: Sectional specification for semi-rigid cables with polyethylene (PE) dielectric 3 Guidance for the prepara
32、tion of detail specifications The detail specification shall be written in accordance with the layout of the blank detail specification, which forms part of this standard. When a characteristic does not apply, then na (for not applicable) is entered in the appropriate space. When a characteristic ap
33、plies but a specific value is not considered necessary, then ns (for not specified) is entered in the appropriate space. The numbers shown in brackets in this and the following pages correspond to the following items of required information, which should be entered in the space provided. 1 Name and
34、address of the organization that has prepared the document 2 IEC document number and date of issue 3 Address of the organization from which the document is available 4 Related documents 5 Any other references to the cable, national reference, trade name, etc. 6 Complete description of the cable 7 Ca
35、ble construction 8 Engineering information 6 IEC 61196-11-1:2016 IEC 2016 9 Parameter or characteristic 10 Reference to the relevant subclause of the sectional specification 11 Minimum requirements, the values entered shall meet as a minimum the requirements of the sectional specification 12 Remarks
36、 4 Blank detail specification Title 1 Prepared by: 2 Document No.: Issue: Date: 3 Available from: 4 Generic specification IEC 61196-1 Sectional specification IEC 61196-11 5 Additional references: References to the different test procedures of Column 10 are given in IEC 61196-11. 6 Cable description:
37、 a) Cable variant b) Material of inner conductor c) Material of dielectric d) Outer conductor e) Material of sheath (if any) 7 Cable construction a) Inner conductor Material: Construction: For corrugated inner conductor: Peak diameter and tolerance (mm): Root diameter and tolerance (mm): Pitch and t
38、olerance (mm): For others: Diameter and tolerance (mm): b) Dielectric Material: PE Construction: Diameter (mm) nominal: Tolerance (mm) tube: (for cable with smooth tube outer conductor) c) Outer conductor Material: Construction: For corrugated outer conductor: Peak diameter and tolerance (mm): Root
39、diameter and tolerance (mm): Pitch and tolerance (mm): For smooth tube outer conductor: Diameter and tolerance (mm): d) Sheath (if any) Material: Minimum thickness (mm): Diameter (mm): Tolerance (mm): IEC 61196-11-1:2016 IEC 2016 7 8 Engineering information (reference only) a) Operating temperature
40、range: b) Maximum operating frequency: c) Nominal characteristic impedance: d) Relative propagation velocity (velocity ratio): e) Maximum continue working voltage: f) Minimum bending radius (static state): g) Minimum bending radius (dynamic state): h) Nominal weight: i) RMS power: j) Peak power: 8 I
41、EC 61196-11-1:2016 IEC 2016 9 Parameter 10 IEC 61196-11:2016 Subclause 11 Value 12 Remarks Electrical characteristics 7.2 Continuity 7.2.1 Inner and outer conductor direct current resistance 7.2.2 /km Withstand voltage of dielectric 7.2.3 kV rms 40 Hz 60 Hz Withstand voltage of sheath (or spark test
42、) 7.2.4 kV rms 40 Hz 60 Hz Insulation resistance 7.2.5 M km 5 000 Mkm according to IEC 61196-11 Capacitance 7.2.6 Frequency: pF/m Mean characteristic impedance 7.2.7 50 200 MHz Regularity of impedance 7.2.8 Return loss 7.2.9 .GHz to GHz dB If necessary, refer to a table or graph at the end of the de
43、tail specification Attenuation 7.2.10 at GHz dB/100 m at 20 C If necessary, refer to a table or graph at the end of the detail specification High temperature cable aginga7.2.11 See 7.3.1 Passive Intermodulation 7.2.12 dBm f 1 = MHz bf 2 = MHz b Input power: 20 W The intermodulation order should be s
44、pecified in accordance with the detail specification. The mechanical stress method in IEC 62037-4 should be specified in accordance with the detail specification. RMS power a7.2.13 W Peak power a7.2.14 W Transfer impedance 7.2.15 m/m frequency: MHz to MHz Screening attenuation 7.2.16 dB Environmenta
45、l characteristics 7.3 Ageing 7.3.1 See IEC 61196-11 Cold bend performance 7.3.2 Temperature at bend C See IEC 61196-11 Water penetration a7.3.3 See IEC 61196-11 Climatic sequence Method 1 a7.3.4 See IEC 61196-11 Environmental stress cracking 7.3.5 See IEC 61196-11 Ultraviolet stability of the sheath
46、 7.3.6 See IEC 61196-11 IEC 61196-11-1:2016 IEC 2016 9 9 Parameter 10 IEC 61196-11:2016 Subclause 11 Value 12 Remarks Mechanical characteristics 7.4 Visual examination 7.4.1 See IEC 61196-11 Dimensional examination 7.4.2 Ovality of inner conductor 7.4.3 % 7 % according to IEC 61196-11 Eccentricity o
47、f dielectric 7.4.4 % 7 % according to IEC 61196-11 Adhesion testing 7.4.5 N Cable bending 7.4.6 See IEC 61196-11 Tensile strength of cable (longitudinal pull) 7.4.7 Force .N See IEC 61196-11 Crush resistance of cable 7.4.8 Force .N See IEC 61196-11 Fire performance requirement 7.5 Flame propagation
48、a7.5.1 When required, according to the detail specification Halogen acid gas emission a7.5.2 When required, according to the detail specification Toxic gas emission a7.5.3 When required, according to the detail specification Smoke density a7.5.4 When required, according to the detail specification aWhen required. bFrequencies are not always fixed frequencies, and can be a swept over a range. _ INTERNATIONAL ELECTROTECHNICAL COMMISSION 3, rue de Varemb PO Box 131 CH-1211 Geneva 20 Switzerland Tel: + 41 22 919 02 11 Fax: + 41 22 919 03 00 infoiec.ch www.iec.ch
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1