IEC 61212-3-3-2006 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 3 Specifications for individu.pdf

1、 IEC 61212-3-3 Edition 2.0 2006-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 3: Specifications for individual materials Sheet 3: Round laminated moulded rods Matriaux iso

2、lants Tubes et barres industriels rigides, ronds, stratifis, base de rsines thermodurcissables, usages lectriques Partie 3: Spcifications pour matriaux particuliers Feuille 3: Barres rondes, stratifies, moules IEC 61212-3-3:2006 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2006 IEC, Geneva, Swi

3、tzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the coun

4、try of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire

5、 aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions su

6、r le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.c

7、h About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant

8、review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). I

9、t also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electr

10、opedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.

11、iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CE

12、I) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous

13、 possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il

14、 donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi

15、 par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electr

16、otechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41

17、22 919 03 00 IEC 61212-3-3 Edition 2.0 2006-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 3: Specifications for individual materials Sheet 3: Round laminated moulded rods

18、Matriaux isolants Tubes et barres industriels rigides, ronds, stratifis, base de rsines thermodurcissables, usages lectriques Partie 3: Spcifications pour matriaux particuliers Feuille 3: Barres rondes, stratifies, moules INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNAT

19、IONALE J ICS 29.035.01 PRICE CODE CODE PRIX ISBN 2-8318-1060-9 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 61212-3-3 IEC:2006 CONTENTS FOREWORD.3 1 Scope.5 2 Normative references .5 3 Terms and definitions .5 4

20、 Designations and abbreviations6 4.1 General .6 4.2 Designation.6 4.3 Abbreviations 6 5 Requirements.6 Table 1 Types of round moulded rods 7 Table 2 Permissible deviation from nominal diameter of round moulded rods 8 Table 3 Departure from straightness for round moulded rods .8 Table 4 Properties of

21、 round moulded rods9 61212-3-3 IEC:2006 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INSULATING MATERIALS INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES Part 3: Specifications for individual materials Sheet 3: Round laminated moulded rods FOREW

22、ORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the elec

23、trical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to tec

24、hnical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Org

25、anization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technic

26、al committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publica

27、tions is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their nation

28、al and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be

29、in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committee

30、s for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the

31、 Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held

32、responsible for identifying any or all such patent rights. International Standard IEC 61212-3-3 has been prepared by IEC technical committee 15: Standards on specifications for electrical insulating materials. This second edition cancels and replaces the first edition published in 1995 and constitut

33、es a technical revision. The main changes from the previous edition are as follows: added application use and safety statements. Reformatted document to bring it up to current IEC document format. Type EP GC 43 has been added. 4 61212-3-3 IEC:2006 This bilingual version, published in 2009-09, corres

34、ponds to the English version. The text of this standard is based on the following documents: FDIS Report on voting 15/329/FDIS 15/344/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this sta

35、ndard has not been voted upon. A list of all parts of the IEC 61212 series, under the general title Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes, can be found on the IEC website. The committee has decided that the contents

36、 of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 61212-3-3

37、 IEC:2006 5 INSULATING MATERIALS INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES Part 3: Specifications for individual materials Sheet 3: Round laminated moulded rods 1 Scope This part of IEC 61212-3 gives requirements for industrial rigid round

38、laminated moulded rods for electrical purposes, based on different resins and different reinforcements. Applications and distinguishing properties are given in Table 1. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a use

39、r for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety Warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they

40、are used in a safe manner. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

41、 IEC 61212-1, Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 1: Definitions, designations and general requirements IEC 61212-2:2006, Insulating materials Industrial rigid round laminated tubes and rods based on thermose

42、tting resins for electrical purposes Part 2: Methods of test ISO 472, Plastics Vocabulary 3 Terms and definitions For the purposes of this document, the following modified definition, which is taken from ISO 472, applies: 3.1 round laminated moulded rod (as applied to thermosets) rod formed by rolli

43、ng impregnated layers of material on a mandrel, removing the mandrel, curing in a cylindrical mould under heat and pressure, and grinding to size ISO 472, MOD 6 61212-3-3 IEC:2006 4 Designations and abbreviations 4.1 General The moulded rods covered by this standard are classified into types which d

44、iffer in the resin and reinforcement used, the method of manufacture, and their distinguishing properties. 4.2 Designation Individual types are designated by: a two-letter abbreviation denoting the resin; a second two-letter abbreviation, denoting the reinforcement; a serial number of two digits, th

45、e first digit denoting the form of the material, a “4” indicates moulded rods, and, a second digit denoting sub-grades of the same type. The abbreviations are given in 4.3. The complete designation of the moulded rod is denoted by: description: Moulded rod; number of the IEC standard: IEC 6121233; d

46、esignation of the individual type; dimensions (in millimetres of the moulded rod: diameter x length) a letter designating the finish on the external diameter of the moulded rod: “A“ designating rods in the “as produced“ condition; “B“ designating rods in ground or turned condition. EXAMPLE: Moulded

47、rod, IEC 61212-3-3 EP CC 41 25x1000 A 4.3 Abbreviations Types of resin Types of reinforcement EP Epoxy (epoxide) CC Woven cotton cloth PF Phenolic GC Woven glass cloth SI Silicone CP Cellulosic paper 5 Requirements In addition to the general requirements given in IEC 61212-1, the moulded rods shall

48、comply with the additional requirements given in Tables 2a, 2b, 3, and 4, with the exception of the length of rod supplied, which shall be subject to agreement between buyer and seller. 61212-3-3 IEC:2006 7 Table 1 Types of round moulded rods Resin Reinforce- ment Serial number Applications and dist

49、inguishing characteristicsaCC 41 Mechanical, electrical and electronic applications. Good resistance to tracking. Fine weaveb .41 Mechanical and electrical applications. High mechanical strength at moderate temperatures. Good stability of electrical properties when exposed to high relative humidity. 42 Similar to EP GC 41, but with high