IEC 61249-2-43-2016 Materials for printed boards and other interconnecting structures - Part 2-43 Reinforced base materials clad and unclad - Non-halogenated epoxide cellulose pape.pdf

1、 IEC 61249-2-43 Edition 1.0 2016-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Materials for printed boards and other interconnecting structures Part 2-43: Reinforced base materials clad and unclad Non-halogenated epoxide cellulose paper/woven E-glass reinforced laminate sheets of defined flammabil

2、ity (vertical burning test), copper-clad for lead-free assembly Matriaux pour circuits imprims et autres structures dinterconnexion Partie 2-43: Matriaux de base renforcs, plaqus et non plaqus Feuilles stratifies renforces en verre de type E tiss/papier cellulose poxyde non halogn, plaques cuivre, d

3、inflammabilit dfinie (essai de combustion verticale) pour les assemblages sans plomb IEC 61249-2-43:2016-05(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2016 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilize

4、d in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional

5、rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun

6、 procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordon

7、nes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global o

8、rganization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an am

9、endment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets an

10、d iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpu

11、blished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definiti

12、ons in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause

13、of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service

14、 Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu tec

15、hnique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes inte

16、rnationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfre

17、nce, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne e

18、t aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 15 langues additionnelles. Egalement appel Vocabulair

19、e Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary 65 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publicati

20、ons des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61249-2-43 Edition 1.0 2016-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Materials for printe

21、d boards and other interconnecting structures Part 2-43: Reinforced base materials clad and unclad Non-halogenated epoxide cellulose paper/woven E-glass reinforced laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly Matriaux pour circuits imprims et au

22、tres structures dinterconnexion Partie 2-43: Matriaux de base renforcs, plaqus et non plaqus Feuilles stratifies renforces en verre de type E tiss/papier cellulose poxyde non halogn, plaques cuivre, dinflammabilit dfinie (essai de combustion verticale) pour les assemblages sans plomb INTERNATIONAL E

23、LECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 31.180 ISBN 978-2-8322-3393-1 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an au

24、thorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 61249-2-43:2016 IEC 2016 CONTENTS FOREWORD 4 1 Scope .6 2 Normative references 6 3 Materials and construction .6 3.1 General 6 3.2 Resin system 6 3.3 Metal foil .7 3.4 Reinfor

25、cement 7 4 Internal marking 7 5 Electrical properties .7 6 Non-electrical properties of the copper-clad laminate .7 6.1 Appearance of the copper-clad sheet 7 6.1.1 General .7 6.1.2 Indentations (pits and dents) 8 6.1.3 Wrinkles 8 6.1.4 Scratches 8 6.1.5 Raised areas .8 6.1.6 Surface waviness .9 6.2

26、Appearance of the unclad face 9 6.3 Laminate thickness .9 6.4 Bow and twist .9 6.5 Properties related to the copper foil bond 10 6.6 Punching and machining . 11 6.7 Dimensional stability . 11 6.8 Sheet sizes . 11 6.8.1 Typical sheet sizes 11 6.8.2 Tolerances for sheet sizes . 11 6.9 Cut panels 12 6.

27、9.1 Cut panel sizes 12 6.9.2 Size tolerances for cut panels 12 6.9.3 Rectangularity of cut panels . 12 7 Non-electrical properties of the base material after complete removal of the copper foil . 12 7.1 Appearance of the dielectric base material 12 7.2 Flexural strength . 13 7.3 Flammability . 13 7.

28、4 Water absorption 14 7.5 Measling . 14 7.6 Glass transition temperature and cure factor . 14 7.7 Decomposition temperature . 14 7.8 Time to delamination (TMA) 15 8 Quality assurance 15 8.1 Quality system 15 8.2 Responsibility for inspection 15 8.3 Qualification inspection . 15 8.4 Quality conforman

29、ce inspection . 15 IEC 61249-2-43:2016 IEC 2016 3 8.5 Certificate of conformance 15 8.6 Safety data sheet 16 9 Packaging and marking . 16 10 Ordering information 16 Annex A (informative) Engineering information . 17 A.1 General 17 A.2 Chemical properties 17 A.3 Electrical properties 17 A.4 Flammabil

30、ity properties . 17 A.5 Mechanical properties . 17 A.6 Physical properties . 17 A.7 Thermal properties 17 Annex B (informative) Common laminate constructions 19 Annex C (informative) Guideline for qualification and conformance inspection 20 Bibliography . 21 Table 1 Electrical properties 7 Table 2 S

31、ize and indentations 8 Table 3 Nominal thickness and tolerance of metal-clad laminate.9 Table 4 Bow and twist requirements . 10 Table 5 Pull-off and peel strength requirements . 10 Table 6 Dimensional stability . 11 Table 7 Size tolerances for cut panels 12 Table 8 Rectangularity of cut panels 12 Ta

32、ble 9 Flexural strength requirements 13 Table 10 Flammability requirements . 13 Table 11 Water absorption requirements 14 Table 12 Measling requirements 14 Table 13 Glass transition temperature and cure factor requirements . 14 Table 14 Decomposition temperature requirements 14 Table 15 Time to dela

33、mination requirements 15 Table C.1 Qualification and conformance inspection . 20 4 IEC 61249-2-43:2016 IEC 2016 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES Part 2-43: Reinforced base materials clad and unclad Non-halogenated epoxide c

34、ellulose paper/woven E-glass reinforced laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committ

35、ees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical R

36、eports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental an

37、d non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreeme

38、nts of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and

39、 are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote i

40、nternational uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated

41、in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All

42、users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or

43、other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publicatio

44、n. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such pa

45、tent rights. International Standard IEC 61249-2-43 has been prepared by IEC technical committee 91: Electronics assembly technology. The text of this standard is based on the following documents: FDIS Report on voting 91/1350/FDIS 91/1363/RVD Full information on the voting for the approval of this s

46、tandard can be found in the report on voting indicated in the above table. IEC 61249-2-43:2016 IEC 2016 5 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 61249 series, under the general title Materials for printed boards and other i

47、nterconnecting structures, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the pu

48、blication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 IEC 61249-2-43:2016 IEC 2016 MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES Part 2-43: Reinforced base materials clad and unclad Non-halogenated epoxide cellulose paper/woven E-glass reinforced

49、laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly 1 Scope This part of IEC 61249 gives requirements for properties of non-halogenated epoxide cellulose paper reinforced core/woven E-glass reinforced surface laminate sheets of defined flammability (vertical burning test), copper-clad for lead-free assembly in thicknesse