IEC 61249-4-1-2008 Materials for printed boards and other interconnecting structures - Part 4-1 Sectional specification set for prepreg materials unclad (for the manufacture of mul.pdf

1、 IEC 61249-4-1 Edition 1.0 2008-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Materials for printed boards and other interconnecting structures Part 4-1: Sectional specification set for prepreg materials, unclad (for the manufacture of multilayer boards) Epoxide woven E-glass prepreg of defined fla

2、mmability Matriaux pour circuits imprims et autres structures dinterconnexion Partie 4-1: Srie de spcifications intermdiaires pour matriaux primprgns, non plaqus (pour la fabrication des cartes multicouches) Tissu de verre poxyde primprgn de type E dinflammabilit dfinie IEC 61249-4-1:2008 THIS PUBLI

3、CATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing

4、from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further informat

5、ion. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national

6、de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-

7、1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The

8、technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety

9、of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released.

10、Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Elec

11、trotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propo

12、s de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications d

13、e la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant d

14、iffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois le

15、s nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans l

16、es langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou con

17、tactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61249-4-1 Edition 1.0 2008-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Materials for printed boards and other interconnecting structures Part 4-1: Sectional specification set for prepreg materials, unclad (for the manuf

18、acture of multilayer boards) Epoxide woven E-glass prepreg of defined flammability Matriaux pour circuits imprims et autres structures dinterconnexion Partie 4-1: Srie de spcifications intermdiaires pour matriaux primprgns, non plaqus (pour la fabrication des cartes multicouches) Tissu de verre poxy

19、de primprgn de type E dinflammabilit dfinie INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE M ICS 31.180 PRICE CODE CODE PRIX ISBN 2-8318-1052-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique I

20、nternationale 2 61249-4-1 IEC:2008 CONTENTS CONTENTS 2 FOREWORD.3 1 Scope.5 2 Normative references .5 3 Materials and construction5 3.1 Reinforcement.6 3.2 Epoxide resin 6 4 Properties.6 4.1 Properties related to the appearance of the prepreg6 4.1.1 Dewetted areas (fish eyes) 6 4.1.2 Broken filament

21、s6 4.1.3 Distortion.6 4.1.4 Creases.6 4.1.5 Edge conditions.6 4.2 Properties related to B stage prepreg 7 4.2.1 Resin content 7 4.2.2 Treated weight.7 4.2.3 Resin flow .7 4.2.4 Scaled flow thickness 7 4.2.5 Melting viscosity8 4.2.6 Gel time.8 4.2.7 Volatile content8 4.3 Properties of prepregs after

22、curing to C stage .8 4.3.1 Electric strength 8 4.3.2 Flammability8 4.3.3 Relative permittivity and dissipation factor.9 4.3.4 Cured thickness.9 5 Delivery form9 5.1 Rolls9 5.2 Sheets.9 5.3 Cut panels.9 6 Quality assurance.10 6.1 Quality system.10 6.2 Responsibility for inspection10 6.3 Qualification

23、 inspection .10 6.4 Quality conformance inspection.10 6.5 Certificate of conformance.10 6.6 Safety data sheet 10 7 Packaging and marking 10 8 Shelf life.11 9 Ordering information.11 Bibliography12 Table 1 Flammability9 61249-4-1 IEC:2008 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MATERIALS FOR PR

24、INTED BOARDS AND OTHER INTERCONNECTING STRUCTURES Part 4-1: Sectional specification set for prepreg materials, unclad (for the manufacture of multilayer boards) Epoxide woven E-glass prepreg of defined flammability FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organi

25、zation for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, I

26、EC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt wi

27、th may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by

28、agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3)

29、IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are

30、used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the

31、 corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have

32、 the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoe

33、ver, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publicati

34、ons is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standar

35、d IEC 61249-4-1 has been prepared by IEC technical committee 91: Electronics assembly technology. This bilingual version, published in 2009-08, corresponds to the English version. The text of this standard is based on the following documents: FDIS Report on voting 91/739/FDIS 91/747/RVD Full informa

36、tion on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 4 61249-4-1 IEC:2008 The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all

37、 parts belonging to the IEC 61249 series, under the general title Materials for printed boards and other interconnecting structures, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on t

38、he IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 61249-4-1 IEC:2008 5 MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES Part 4-1: Sec

39、tional specification set for prepreg materials, unclad (for the manufacture of multilayer boards) Epoxide woven E-glass prepreg of defined flammability 1 Scope This part of IEC 61249 gives requirements for properties of prepreg that is mainly intended to be used as bonding sheets in connection with

40、laminates according to IEC 61249-2-7 when manufacturing multilayer boards in line with IEC 62326-4. This material may be also used to bond other types of laminates. Prepreg according to this standard is of defined flammability (vertical burning test). The flammability rating on fully cured prepreg i

41、s achieved through the use of brominated fire retardants contained as an integral part of the polymeric structure. After lamination according to the suppliers instructions, the glass transition temperature is defined as being 120 C minimum. 2 Normative references The following referenced documents a

42、re indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61189-2:2006, Test methods for electrical materials, printed boards and other int

43、erconnection structures and assemblies Part 2: Test methods for materials for interconnection structures IEC 61189-3:1997, Test methods for electrical materials, printed boards and other interconnection structures and assemblies Part 3: Test methods for interconnection structures (printed boards) IE

44、C 61249-2-7:2002, Materials for printed boards and other interconnecting structures Part 2-7: Reinforced base materials clad and unclad Epoxide woven E-glass laminated sheet of defined flammability (vertical burning test), copper-clad IEC 62326-4, Printed boards Part 4: Rigid multilayer printed boar

45、ds with interlayer connections Sectional specification ISO 9000:2005, Quality management systems Fundamentals and vocabulary ISO 11014-1:1994, Safety data sheet for chemical products Part 1: Content and order of sections ISO 14001:2004, Environmental management systems Requirements with guidance for

46、 use 3 Materials and construction The prepreg consists of a reinforcing E-glass fabric which is impregnated with epoxide resin and partially cured to the B stage. 6 61249-4-1 IEC:2008 3.1 Reinforcement NOTE Woven E-glass is intended to be specified in the future IEC 61249-6-3. 3.2 Epoxide resin Majo

47、rity di-functional epoxide resin with a glass transition temperature of 120 C when cured according to the manufacturers recommendation. Contrast agents may be added to enhance processing such as optical inspection. Its flame resistance is defined in terms of the flammability requirements of 4.3.2. 4

48、 Properties 4.1 Properties related to the appearance of the prepreg The prepreg shall be substantially free from defects that may have an impact on the materials fitness for use for the intended purpose. For the following specific defects, the requirements given shall apply when inspection is made i

49、n accordance with IEC 61189-3, method 3V01: Visual examination 3 magnification. 4.1.1 Dewetted areas (fish eyes) Dewetted areas with a diameter 5 mm are not permissible. Dewetted areas with a diameter 5 mm are permitted to an extent of a maximum 10 fish eyes in any 300 mm 300 mm area of the prepreg. 4.1.2 Broken filaments When judging the presence of broken f