IEC 61300-3-25-2016 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-25 Examinations and measurements - Concentricity of .pdf

1、 IEC 61300-3-25 Edition 3.0 2016-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-25: Examinations and measurements Concentricity of non-angled ferrules and non-angled ferrules with fibre installed

2、Dispositifs dinterconnexion et composants passifs fibroniques Procdures fondamentales dessais et de mesures Partie 3-25: Examens et mesures Concentricit des frules sans angle et des frules sans angle avec fibre monte IEC 61300-3-25:2016-08(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 201

3、6 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Com

4、mittee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf in

5、dication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez de

6、s questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 G

7、eneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of

8、 IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC In

9、ternational Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical

10、committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia

11、 - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - st

12、d.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore

13、.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internatio

14、nales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalo

15、gue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications

16、 IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublish

17、ed Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient 20 000 terme

18、s et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 15 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary 65 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites

19、 des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des ques

20、tions contactez-nous: csciec.ch. IEC 61300-3-25 Edition 3.0 2016-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-25: Examinations and measurements Concentricity of non-angled ferrules and non-angle

21、d ferrules with fibre installed Dispositifs dinterconnexion et composants passifs fibroniques Procdures fondamentales dessais et de mesures Partie 3-25: Examens et mesures Concentricit des frules sans angle et des frules sans angle avec fibre monte INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSIO

22、N ELECTROTECHNIQUE INTERNATIONALE ICS 33.180.20 ISBN 978-2-8322-3618-5 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention!

23、Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 61300-3-25:2016 IEC 2016 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references. 5 3 General description . 5 3.1 General . 5 3.2 Method A: ferrule surface reference method (reference test method) 6 3.3 Method

24、 B: core centre reference method on a ferrule with fibre installed 6 4 Apparatus 6 4.1 Method A 6 4.2 Method B 6 5 Procedure . 6 5.1 Method A-1 . 6 5.2 Method A-2 . 7 5.3 Method B 8 6 Details to be specified . 9 6.1 Method A 9 6.2 Method B 9 Bibliography . 10 Figure 1 Definition of concentricity . 5

25、 Figure 2 Set-up example for concentricity measurement (method A-1) of ferrules with fibre installed . 7 Figure 3 Set-up example for concentricity measurement (method A-2) of bare ferrules . 8 Figure 4 Set-up example for concentricity measurement (method B) of ferrules with fibre installed 9 IEC 613

26、00-3-25:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-25: Examinations and measurements Concentricity of non-angled ferrules and non-angled ferrules with fibre installed FOREWORD 1)

27、The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical

28、and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical

29、committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organizati

30、on for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical comm

31、ittee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications i

32、s accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and

33、regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and

34、, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or

35、agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use

36、of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that so

37、me of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61300-3-25 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of

38、 IEC technical committee 86: Fibre optics. This third edition cancels and replaces the second edition published in 2013 and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: a) deletion of method C due to potenti

39、al damage of ferrule end face by the spindle. Method C is the ferrule bore reference method for bare ferrules according to IEC 61300-3-25:2013; b) separation of original method A into method A-1 and method A-2 relating to the two different types of ferrule (with/without fibre fitted); c) integration

40、 of the content of Annexes A and B into the test procedure. 4 IEC 61300-3-25:2016 IEC 2016 The text of this standard is based on the following documents: CDV Report on voting 86B/3900/CDV 86B/3956A/RVC Full information on the voting for the approval of this document can be found in the report on vot

41、ing indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 61300 series, published under the general title, Fibre optic interconnecting devices and passive components Basic test and measurement procedures, can be

42、 found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will be reconfirmed, withdrawn, r

43、eplaced by a revised edition, or amended. IEC 61300-3-25:2016 IEC 2016 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-25: Examinations and measurements Concentricity of non-angled ferrules and non-angled ferrules with fibre installed 1 Scope

44、 This part of IEC 61300 describes the procedure to determine the concentricity of the axis of the bore in a non-angled ferrule with the axis of the ferrule, and in the case of non-angled ferrules with fibre installed, to determine the concentricity of the axis of the fibre core with the axis of the

45、ferrule. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (

46、including any amendments) applies. There are no normative references in this document. 3 General description 3.1 General This procedure describes the measurement of concentricity of ferrules and ferrules with assembled fibres. Concentricity is defined as twice the distance between the axis of the fe

47、rrule and the axis of the inner diameter of the ferrule (ferrule bore), or in the case of ferrules with fibre installed, twice the distance between the axis of the ferrule and the axis of the core of the installed fibre (see Figure 1). When concentricity measurements are made on a ferrule with fibre

48、 installed the results will be affected by the geometry of the fibre, and by the fit of the fibre in the ferrule inner diameter. Imperfections of the cylindricity and circularity of the outside diameter of the ferrule will influence the measurement results. Figure 1 Definition of concentricity Two m

49、ethods of concentricity measurement are described in 3.2 and 3.3. IEC C Axis of ferrule Concentricity Axis of fibre core or ferrule bore Fibre core or ferrule bore Ferrule 6 IEC 61300-3-25:2016 IEC 2016 3.2 Method A: ferrule surface reference method (reference test method) In Method A, the ferrule is placed in a V-groove or outer diameter (OD) reference mechanism, and rotated. The displacement o