IEC 61300-3-49-2013 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-49 Examinations and measurement Guide pin retention .pdf

1、 IEC 61300-3-49 Edition 1.0 2013-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-49: Examinations and measurements Guide pin retention force for rectangular ferrule multi-fibre connectors Dispositi

2、fs dinterconnexion et composants passifs fibres optiques Procdures fondamentales dessais et de mesures Partie 3-49: Examens et mesures Force de rtention de la broche de guidage des connecteurs multifibres frule rectangulaire IEC61300-3-49:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 I

3、EC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Commit

4、tee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indic

5、ation contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez d

6、es questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1

7、211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical conte

8、nt of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a varie

9、ty of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available o

10、n-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International E

11、lectrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) e

12、st la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous pos

13、sdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi d

14、es informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Ele

15、ctropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique Int

16、ernational (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61300-3-49 Edition 1.0 2013-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devic

17、es and passive components Basic test and measurement procedures Part 3-49: Examinations and measurements Guide pin retention force for rectangular ferrule multi-fibre connectors Dispositifs dinterconnexion et composants passifs fibres optiques Procdures fondamentales dessais et de mesures Partie 3-4

18、9: Examens et mesures Force de rtention de la broche de guidage des connecteurs multifibres frule rectangulaire INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-83220-656-0 Registered trademark of the International E

19、lectrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61300-3-49 IEC:2013 CONTEN

20、TS FOREWORD . 3 1 Scope . 5 2 Normative references . 5 3 General description 5 3.1 General . 5 3.2 Test conditions 5 4 Apparatus . 6 4.1 Fixture . 6 4.2 Guide pin chuck 6 4.3 Weight . 6 4.4 Tensile testing machine . 6 5 Procedure . 6 5.1 Method A: Method using weight (Figure 1) . 6 5.2 Method B: Met

21、hod using tensile testing machine (Figure 2) . 7 6 Details to be specified 8 Figure 1 Method for examination of guide pin retention force (method using weight) 7 Figure 2 Method for examination of guide pin retention force (method using tensile testing machine) . 8 Table 1 Test conditions 6 61300-3-

22、49 IEC:2013 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-49: Examinations and measurements Guide pin retention force for rectangular ferrule multi-fibre connectors FOREWORD 1) The International E

23、lectrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fiel

24、ds. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC

25、 National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardizati

26、on (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representa

27、tion from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cann

28、ot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publication

29、s. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, acc

30、ess to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including ind

31、ividual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon

32、, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements o

33、f this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61300-3-49 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical commi

34、ttee 86: Fibre optics. The text of this standard is based on the following documents: CDV Report on voting 86B/3437/CDV 86B/3497A/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted

35、in accordance with the ISO/IEC Directives, Part 2. 4 61300-3-49 IEC:2013 A list of all parts in the IEC 61300 series, published under the general title, Fibre optic interconnecting devices and passive components Basic test and measurement procedures, can be found on the IEC website. The committee ha

36、s decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or

37、amended. 61300-3-49 IEC:2013 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-49: Examinations and measurements Guide pin retention force for rectangular ferrule multi-fibre connectors 1 Scope The purpose of this part of IEC 61300 is to descri

38、be the procedure required to measure the guide pin retention force for rectangular ferrule multi-fibre connectors in order to ensure that the pins remain in place during mating/unmating. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document

39、and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1:2011, Fibre optic interconnecting devices and passive components Basic test and measu

40、rement procedures Part 1: General and guidance IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61754-7, Fibre optic interconnecting devices and passive components Fibre opti

41、c connector interfaces Part 7: Type MPO connector family IEC 61754-10, Fibre optic connector interfaces Part 10: Type Mini-MPO connector family IEC 61754-18, Fibre optic connector interfaces Part 18: Type MT-RJ connector family 3 General description 3.1 General This measurement method is applied for

42、 optical connectors specified in IEC 61754-7, IEC 61754-10 and IEC 61754-18. This standard describes two methods using weight or a tensile testing machine. The optical connector is held using a fixture. The guide pin is placed in a guide pin chuck. The weight or tensile testing machine is connected

43、to the guide pin chuck. A measurement of guide pin retention force is taken. 3.2 Test conditions For precise measurements such as for design verification, test conditions shall be controlled accurately as required in Table 1 of IEC 61300-1:2011. Table 1 below is an adaptation of that table. 6 61300-

44、3-49 IEC:2013 Table 1 Test conditions Temperature T Relative humidity RH 22,0 C to 24,0 C (50,0 10,0) % RH 4 Apparatus 4.1 Fixture The measurement shall not be affected by the connector fixture. The position and direction of connector during the test shall not change as the test is repeated. The con

45、nector shall be placed in the fixture so that the front face of connector housing is retained by the fixture as shown in Figure 1 and Figure 2. 4.2 Guide pin chuck The guide pin chuck shall have a pin retention force much larger than required connector guide pin retention force. More than 200 N is i

46、deal when using a tensile testing machine. The connection of the guide pin chuck to the weight or tensile testing machine shall not affect the measurement nor divert the applied force from the axis of guide pin. 4.3 Weight The weight to be used depends on the test to be carried out. The weight measu

47、rement is used for pass/fail tests including final inspection. 4.4 Tensile testing machine The tensile testing machine shall be able to record (and/or hold) the maximum value during the measurement. Tensile testing machine measurement is used for design verification testing. 5 Procedure 5.1 Method A

48、: Method using weight (Figure 1) a) Prepare the DUT according to the manufacturers instructions and check the appearance in accordance with IEC 61300-3-1. b) Place the DUT in the fixture and check the appearance. c) Place the guide pin in the chuck. d) Fix the weight to the guide pin chuck. Adjust t

49、he total weight of chuck and weight to the specified value. Ensure the DUT is fixed vertical. e) Apply the weight slowly. Be sure that the DUT remains vertical and the force is applied in the axis of the guide pin. f) Wait for the specified duration. Record whether or not the guide pin remains in place for the specified force. Unless otherwise specified, the minimum duration shall be 5