IEC 61326-2-5-2012 Electrical equipment for measurement control and laboratory use - EMC requirements - Part 2-5 Particular requirements - Test configurations operational condition.pdf

1、 IEC 61326-2-5 Edition 2.0 2012-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-5: Particular requirements Test configurations, operational conditions and performance criteria for field devices with field bus int

2、erfaces according to IEC 61784-1 Matriel lectrique de mesure, de commande et de laboratoire Exigences relatives la CEM Partie 2-5: Exigences particulires Configurations dessai, conditions de fonctionnement et critres daptitude la fonction pour les quipements de terrain avec des interfaces utilisant

3、des bus de terrain conformes la CEI 61784-1 IEC61326-2-5:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanic

4、al, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the addres

5、s below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photoco

6、pie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de l

7、a CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes Inter

8、national Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful lin

9、ks: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpu

10、blished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms a

11、nd definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please co

12、ntact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des pub

13、lications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche avance vous permet de tr

14、ouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications de la CEI. J

15、ust Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en fran

16、ais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: cscie

17、c.ch. IEC 61326-2-5 Edition 2.0 2012-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Electrical equipment for measurement, control and laboratory use EMC requirements Part 2-5: Particular requirements Test configurations, operational conditions and performance criteria for field devices with field bu

18、s interfaces according to IEC 61784-1 Matriel lectrique de mesure, de commande et de laboratoire Exigences relatives la CEM Partie 2-5: Exigences particulires Configurations dessai, conditions de fonctionnement et critres daptitude la fonction pour les quipements de terrain avec des interfaces utili

19、sant des bus de terrain conformes la CEI 61784-1 INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE Q ICS 17.220; 25.040.40; 33.100 PRICE CODE CODE PRIX ISBN 978-2-83220-396-5 Registered trademark of the International Electrotechnical Commission Marque dpose de la C

20、ommission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61326-2-5 IEC:2012 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative referenc

21、es . 5 3 Terms and definitions . 6 4 General 6 5 EMC test plan . 6 5.1 General . 6 5.2 Configuration of EUT during testing . 6 5.3 Operation conditions of EUT during testing 6 5.4 Specification of functional performance . 6 5.5 Test description . 6 6 Immunity requirements . 6 6.1 Conditions during t

22、he tests 6 6.2 Immunity test requirements . 6 6.3 Random aspects 6 6.4 Performance criteria 7 7 Emission requirements . 7 8 Test results and test report . 7 9 Instructions for use . 7 Annex AA (normative) Particular requirements Test configurations, operational conditions and performance criteria fo

23、r field devices with field bus interfaces according to IEC 61784-1 CP 1/1 8 Annex BB (normative) Particular requirements Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1 CP 3/2 13 Figure AA.1 Test set up for EUT

24、 with CP 1/1 interface . 10 Figure BB.1 Test set up for EUT with CP 3/2 interface . 15 61326-2-5 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATORY USE EMC REQUIREMENTS Part 2-5: Particular requirements Test configurations, operational

25、 conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1 FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The

26、 object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifi

27、cations (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations l

28、iaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters exp

29、ress, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Commi

30、ttees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Nation

31、al Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does n

32、ot provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have

33、the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoev

34、er, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publicatio

35、ns is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard

36、 IEC 61326-2-5 has been prepared by subcommittee 65A: System aspects, of IEC technical committee 65: Industrial-process measurement, control and automation. This second edition cancels and replaces the first edition published in 2006. This edition constitutes a technical revision. 4 61326-2-5 IEC:20

37、12 The main technical changes with regard to the previous edition are as follows: Update with respect to IEC 61326-1:2012. The text of this standard is based on the following documents: FDIS Report on voting 65A/643/FDIS 65A/654/RVD Full information on the voting for the approval of this standard ca

38、n be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. This part of IEC 61326 series is to be used in conjunction with IEC 61326-1:2012 and follows the same numbering of clauses, subclauses, tables and fig

39、ures. When a particular subclause of IEC 61326-1 is not mentioned in this part, that subclause applies as far as is reasonable. When this standard states “addition”, “modification” or “replacement”, the relevant text in IEC 61326-1 is to be adapted accordingly. NOTE The following numbering system is

40、 used: subclauses, tables and figures that are numbered starting from 101 are additional to those in IEC 61326-1; unless notes are in a new subclause or involve notes in IEC 61326-1, they are numbered starting from 101 including those in a replaced clause or subclause; additional annexes are lettere

41、d AA, BB, etc. A list of all parts of IEC 61326 series, under the general title Electrical equipment for measurement, control and laboratory use EMC requirements can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability

42、 date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61326-2-5 IEC:2012 5 ELECTRICAL EQUIPMENT FOR MEASUREMENT, CONTROL AND LABORATOR

43、Y USE EMC REQUIREMENTS Part 2-5: Particular requirements Test configurations, operational conditions and performance criteria for field devices with field bus interfaces according to IEC 61784-1 1 Scope In addition to the requirements of International Standard IEC 61326-1, this part of IEC 61326 tre

44、ats the particular features for EMC testing of field devices with field bus interfaces. This part of IEC 61326 covers only the field bus interface of the equipment. NOTE The other functions of the equipment remain covered by other parts of IEC 61326 series. This part refers only to field devices int

45、ended for use in process control and process measuring. In this standard field devices with interfaces according to IEC 61784-1, CP 3/2 and CP 1/1 as defined in IEC 61784 are covered. Other field busses may be included in future editions of this standard. The IEC 61784-1 specifies a set of protocol

46、specific communication profiles based on IEC 61158. The manufacturer specifies the environment for which the product is intended to be used and/or selects the appropriate test level specifications of IEC 61326-1. 2 Normative references The following documents, in whole or in part, are normatively re

47、ferenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Clause 2 of IEC 61326-1 applies except as follows: Addition: IEC 61158-

48、2:2010, Industrial communication networks Fieldbus specifications Part 2: Physical layer specification and service definition IEC 61158-3-3:2007, Industrial communication networks Fieldbus specifications Part 3-3: Data-link layer service definition Type 3 elements IEC 61158-5-5:2007, Industrial comm

49、unication networks Fieldbus specifications Part 5-5: Application layer service definition Type 5 elements IEC 61158-6-10:2010, Industrial communication networks Fieldbus specifications Part 6-10: Application layer protocol specification Type 10 elements 6 61326-2-5 IEC:2012 IEC 61784-1:2010, Industrial communication networks Profiles Part 1: Fieldbus profiles 3 Terms