IEC 61755-2-5-2015 Fibre optic interconnecting devices and passive components - Connector optical interfaces - Part 2-5 Connection parameters of non-dispersion shifted single-mode .pdf

1、 IEC 61755-2-5 Edition 1.0 2015-01 INTERNATIONAL STANDARD Fibre optic interconnecting devices and passive components Connector optical interfaces Part 2-5: Connection parameters of non-dispersion shifted single-mode physically contacting fibres Angled for reference connection applications IEC 61755-

2、2-5:2015-01(en) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and m

3、icrofilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member

4、 National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and pub

5、lishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published

6、. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search -

7、 www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all ne

8、w IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and Fren

9、ch, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC public

10、ations issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csci

11、ec.ch. IEC 61755-2-5 Edition 1.0 2015-01 INTERNATIONAL STANDARD Fibre optic interconnecting devices and passive components Connector optical interfaces Part 2-5: Connection parameters of non-dispersion shifted single-mode physically contacting fibres Angled for reference connection applications INTE

12、RNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.180.20 ISBN 978-2-8322-2194-5 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. colour inside 2 IEC 61755-2-5:2015 IEC 2015 CONTENTS FOREWORD . 3 1 S

13、cope 5 2 Normative references 5 3 Performance grades 6 4 Description 6 5 Criteria for a fit within performance grades 7 5.1 General . 7 5.2 Attenuation grades and criteria . 7 6 Use of selected fibre to assemble reference connector plugs . 9 7 Reference adaptor . 9 8 Attenuation measurement uncertai

14、nty contribution . 9 Annex A (informative) Example of determination of the attenuation measurement uncertainty 10 Figure 1 Representation of fibre core position of single connector plug under the assumption of worst case alignment with identical connector plug. 8 Figure A.1 Attenuation measurement u

15、ncertainty contribution for Grade 1 reference connectors 10 Table 1 Single-mode attenuation grades at 1 310 nm (dB) . 6 Table 2 Mode field diameter and fibre core nominal index of refraction for fibre to be used in reference connector plugs 7 Table 3 Measurement uncertainty contribution of reference

16、 connectors . 9 IEC 61755-2-5:2015 IEC 2015 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS CONNECTOR OPTICAL INTERFACES Part 2-5: Connection parameters of non-dispersion shifted single-mode physically contacting fibres Angled for reference co

17、nnection applications FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning

18、standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their prep

19、aration is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

20、 with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant

21、subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the techn

22、ical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum exte

23、nt possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide

24、conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its

25、directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses ar

26、ising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention i

27、s drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61755-2-5 has been prepared by subcommittee 86B: Fibre optic interconnecting d

28、evices and passive components, of IEC technical committee 86: Fibre optics. The text of this standard is based on the following documents: FDIS Report on voting 86B/3846/FDIS 86B/3867/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated

29、in the above table. 4 IEC 61755-2-5:2015 IEC 2015 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 61755 series, published under the general title Fibre optic interconnecting devices and passive components Connector optical interface

30、s, can be found on the IEC website. Future standards in this series will carry the new general title as cited above. Titles of existing standards in this series will be updated at the time of the next edition. The committee has decided that the contents of this publication will remain unchanged unti

31、l the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later

32、date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. IEC 61755-2-5:2015 IEC 2015 5 FIBRE OPTI

33、C INTERCONNECTING DEVICES AND PASSIVE COMPONENTS CONNECTOR OPTICAL INTERFACES Part 2-5: Connection parameters of non-dispersion shifted single-mode physically contacting fibres Angled for reference connection applications 1 Scope This part of IEC 61755 defines a set of prescribed conditions that sho

34、uld be maintained in order to satisfy the requirements of angled polished reference connections. The prescribed conditions include dimensional limits and optical fibre requirements of the optical interface to meet specific requirements for reference connection (plugs and adaptors) used for attenuati

35、on measurements. Two different grades for reference connections are defined in this standard. The use of each of these grades depends on the application and on the targeted attenuation measurement uncertainty. The model uses a Gaussian distribution of light intensity over the specified restricted mo

36、de field diameter (MFD) range. This standard is intended to be used for shipping and acceptance inspections. The reference connector plug is specified for B1.1, B1.3 and B6 fibres as specified in IEC 60793-2-50. The use of the reference connector plug would not be recommended where classification of

37、 fibre is difficult, for example construction and maintenance of cable plant. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated

38、references, the latest edition of the referenced document (including any amendments) applies. IEC 60793-2-50, Optical fibres Part 2-50: Product specifications Sectional specification for class B single-mode fibres IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test a

39、nd measurement procedures Part 3-4: Examinations and measurements Attenuation IEC 61300-3-42, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-42: Examinations and measurements Attenuation of single mode alignment sleeves and or adaptors with re

40、silient alignment sleeves IEC 61755-2-1, Fibre optic interconnecting devices and passive components Connector optical interfaces Part 2-1: Connection parameters of non-dispersion shifted single-mode physically contacting fibres Non-angled 6 IEC 61755-2-5:2015 IEC 2015 IEC 61755-2-2, Fibre optic inte

41、rconnecting devices and passive components Connector optical interfaces Part 2-2: Connection parameters of non-dispersion shifted single-mode physically contacting fibres Angled IEC 61755-3 (all parts), Fibre optic interconnecting devices and passive components Connector optical interfaces Part 3-x:

42、 Connector parameters of non-dispersion shifted single-mode physically contacting fibres IEC TR 62627-04, Fibre optic interconnecting devices and passive components Technical report Part 04: Example of uncertainty calculation: Measurement of the attenuation of an optical connector. 3 Performance gra

43、des Performance grades for APC polished reference connectors are given in Table 1. The specified attenuation for each grade is obtained when the reference plugs are connected to each other with the reference adaptor. Table 1 Single-mode attenuation grades at 1 310 nm (dB) Reference grade aAttenuatio

44、n adB Contribution to measurement uncertainty bdB R1 0,1 0,1 R2 0,2 0,2 aUnder the assumption of worst case alignment with identical connector plug. Expected attenuation measured when connecting two plugs of the same grade may be higher due to significant measurement uncertainty bAs described in Cla

45、use 8. 4 Description Optical reference connector plugs are connector plugs manufactured with restricted tolerances for dimensions relevant to lateral and angular offset. These connector plugs are used for attenuation measurement purposes according to IEC 61300-3-4, and shall be considered as part of

46、 the measurement set-up since they strongly contribute to its measurement uncertainty (for example see IEC TR 62627-04). The attenuation measurement uncertainty contributions for both grades of reference connectors are listed in Table 3. The principal performance of a reference connector plug is giv

47、en by its contribution to measurement uncertainty (estimated based on the reproducibility of an attenuation measurement of the same device performed using multiple different reference connector plugs of the same grade) which is determined by the accuracy with which the core of the optical fibre is a

48、ligned to the optical datum target and determines the random attenuation performance of a reference connector population. The main parameters influencing the performance of the reference connector plugs are fibre core location, fibre core axis angle and mode field diameter variability. Figure 1 repr

49、esents the fibre alignment tolerances for the two different reference grades described in this standard, under the assumption of using selected reference fibre, described in Table 2. The design curves given in Figure 1 each represent maximum allowable combinations of a given specific fibre core location and an associated fibre core axis angle to not exceed the specified attenuation of any single considered connection. The design curves shown represent