IEC 61987-24-2-2017 Industrial-process measurement and control - Data structures and elements in process equipment catalogues - Part 24-2 Lists of properties (LOPs) of valve actuat.pdf

1、 IEC 61987-24-2 Edition 1.0 2017-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial-process measurement and control Data structures and elements in process equipment catalogues Part 24-2: Lists of properties (LOPs) of valve/actuator accessories for electronic data exchange Mesure et commande

2、dans les processus industriels Structures de donnes et lments dans les catalogues dquipements de processus Partie 24-2: Listes de proprits (LOP) des accessoires dactionneur/de vanne pour lchange lectronique de donnes IEC 61987-24-2:2017-06(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 201

3、7 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Com

4、mittee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf in

5、dication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez de

6、s questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 G

7、eneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of

8、 IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC In

9、ternational Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical

10、committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia

11、 - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 16 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - st

12、d.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore

13、iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internatio

14、nales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalo

15、gue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications

16、 IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublish

17、ed Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient 20 000 terme

18、s et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 16 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary 65 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites

19、 des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des ques

20、tions contactez-nous: csciec.ch. IEC 61987-24-2 Edition 1.0 2017-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Industrial-process measurement and control Data structures and elements in process equipment catalogues Part 24-2: Lists of properties (LOPs) of valve/actuator accessories for electronic d

21、ata exchange Mesure et commande dans les processus industriels Structures de donnes et lments dans les catalogues dquipements de processus Partie 24-2: Listes de proprits (LOP) des accessoires dactionneur/de vanne pour lchange lectronique de donnes INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSIO

22、N ELECTROTECHNIQUE INTERNATIONALE ICS 01.110; 25.040.40; 35.240.50 ISBN 978-2-8322-4405-0 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distr

23、ibutor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 61987-24-2:2017 IEC 2017 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normative references 6 3 Terms and definitions 7 4 General . 7 4.1 Overview. 7 4.2 Depiction of OLOP and DLOPs .

24、7 4.3 Example of DLOP block usage for a solenoid valve (informative) 7 Annex A (normative) Operating list of properties for valve/actuator accessories . 10 Annex B (normative) Device list of properties for valve/actuator accessories . 11 B.1 DLOP for filter regulator 11 B.2 DLOP for limit switch 11

25、B.3 DLOP for position transmitter 11 B.4 DLOP for solenoid valve . 12 Annex C (normative) List of properties for valve/actuator accessories Property library . 13 Annex D (normative) List of properties for valve/actuator accessories Block library . 14 Bibliography 15 Table 1 Example for a solenoid va

26、lve . 8 IEC 61987-24-2:2017 IEC 2017 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL-PROCESS MEASUREMENT AND CONTROL DATA STRUCTURES AND ELEMENTS IN PROCESS EQUIPMENT CATALOGUES Part 24-2: Lists of properties (LOPs) of valve/actuator accessories for electronic data exchange FOREWORD 1) The

27、International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and

28、electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical comm

29、ittees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization f

30、or Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committe

31、e has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is ac

32、curate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regi

33、onal publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in

34、 some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agen

35、ts including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of,

36、or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some o

37、f the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61987-24-2 has been prepared by subcommittee 65B: Measurement and control devices, of IEC technical committee 65: In

38、dustrial-process measurement, control and automation. The text of this International Standard is based on the following documents: CDV Report on voting 65B/1036/CDV 65B/1065/RVC Full information on the voting for the approval of this International Standard can be found in the report on voting indica

39、ted in the above table. 4 IEC 61987-24-2:2017 IEC 2017 This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 61987 series, published under the general title Industrial-process measurement and control Data structures and elements in process e

40、quipment catalogues, can be found on the IEC website. The committee has decided that the contents of this document will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific document. At this date, the document will b

41、e reconfirmed, withdrawn, replaced by a revised edition, or amended. IEC 61987-24-2:2017 IEC 2017 5 INTRODUCTION The exchange of product data between companies, business systems, engineering tools, data systems within companies and, in the future, control systems (electrical, measuring and control t

42、echnology) can run smoothly only when both the information to be exchanged and the use of this information has been clearly defined. Prior to IEC 61987, requirements on process control devices and systems were specified by customers in various ways when suppliers or manufacturers were asked to quote

43、 for suitable equipment. The suppliers in their turn described the devices according to their own documentation schemes, often using different terms, structures and media (paper, databases, CDs, e-catalogues, etc.). The situation was similar in the planning and development process, with device infor

44、mation frequently being duplicated in a number of different information technology (IT) systems. Any method that is capable of recording all existing information only once during the planning and ordering process and making it available for further processing, gives all parties involved an opportuni

45、ty to concentrate on the essentials. A precondition for this is the standardization of both the descriptions of the objects and the exchange of information. IEC 61987 (all parts) proposes a method for standardization which will help both suppliers and users of process control equipment to optimize w

46、orkflows both within their own companies and in their exchanges with other companies. Depending on their role in the process, engineering firms can be considered here to be either users or suppliers. The method specifies process control equipment by means of blocks of properties. These blocks are co

47、mpiled into lists of properties (LOPs), each of which describes a specific equipment (device) type. IEC 61987 (all parts) covers both properties that can be used in an inquiry or a proposal and detailed properties required for integration of the equipment in computer systems for other tasks. Part 10

48、 of IEC 61987 defines structure elements for constructing lists of properties for electrical and process control equipment in order to facilitate automatic data exchange between any two computer systems in any possible workflow, for example engineering, maintenance or purchasing workflow and to allo

49、w both the customers and the suppliers of the equipment to optimize their processes and workflows. Part 10 also provides the data model for assembling the LOPs. Part 11 of IEC 61987, while specifying a generic structure for measuring equipment, provides several important detail descriptions, such as the handling of composite devices that are also required for LOPs describing devices of other areas like the auto