IEC 62314-2006 Solid-state relays《固态继电器》.pdf

1、 INTERNATIONAL STANDARD IEC 62314First edition 2006-05Solid-state relays Reference number IEC 62314:2006(E) Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editi

2、ons The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC pu

3、blications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to ne

4、w editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue

5、 of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced pu

6、blications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/online_news/ justpub) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding

7、 this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IEC 62314First edition 2006-05Solid-state relays IEC 2006 Copyright - all rights reserved No part of this publication may

8、 be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 1

9、1 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch W For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 62314 IEC:2006(E) CONTENTS FOREWORD.4 1 Scope and object6 2 Normative references .7 3 Terms and defini

10、tions .8 4 Characteristics of solid-state relays 12 4.1 Summary of characteristics .12 4.2 Type of solid-state relay 12 4.3 Rated and limiting values for load circuits12 4.4 Load category .13 4.5 Rated and limiting values for control circuits14 5 Marking and documentation14 5.1 Marking .14 5.2 Data

11、15 5.3 Instructions for installation, operation and maintenance 15 6 Normal conditions.15 6.1 Normal service, transport and storage conditions 15 6.2 Normal mounting conditions 16 7 Constructional requirements.16 7.1 Materials .16 7.2 Clearances and creepage distances 16 7.3 Heat and fire resistance

12、 16 7.4 Terminals 16 8 Performance requirements .17 8.1 Temperature-rise.17 8.2 Overload test.18 8.3 Endurance test20 8.4 Insulation tests21 8.5 Impact test 21 8.6 Ball pressure test 21 8.7 OFF-state leakage current measurement.21 8.8 ON-state voltage drop measurement .21 9 Type test 22 Annex A (nor

13、mative) Insulation coordination 23 Annex B (normative) Glow-wire test.34 Annex C (normative) Quick-connect terminations.37 Figure B.1 Glow-wire and position of the thermocouple35 Figure B.2 Glow-wire test apparatus (example)36 62314 IEC:2006(E) 3 Table 1 Load categories.13 Table 2 Required data .15

14、Table 3 Test conditions for test Tb.17 Table 4 Minimum requirements for overload capability test conditions .19 Table 5 Endurance test20 Table A.1 Rated impulse withstand voltages (waveform: 1,2/50 s) for solid-state relays connected directly to the mains 24 Table A.2 Minimum clearances 26 Table A.3

15、 Minimum creepage distances for solid-state relays 27 Table A.4 Preconditioning29 Table C.1 Cross-sectional areas for conductors depending on the resistive current carried by the terminal 38 4 62314 IEC:2006(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ SOLID-STATE RELAYS FOREWORD 1) The Internatio

16、nal Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic

17、 fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; an

18、y IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standar

19、dization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has repr

20、esentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IE

21、C cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publi

22、cations. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an

23、 IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal in

24、jury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references

25、 cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for ident

26、ifying any or all such patent rights. International Standard IEC 62314 has been prepared by technical committee 94: All-or- nothing electrical relays. The text of this standard is based on the following documents: FDIS Report on voting 94/232/FDIS 94/235/RVD Full information on the voting for the ap

27、proval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 62314 IEC:2006(E) 5 The committee has decided that the contents of this publication will remain unchanged until the maintena

28、nce result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date.

29、 6 62314 IEC:2006(E) SOLID-STATE RELAYS 1 Scope and object This International Standard applies to particular all-or-nothing electrical relays denominated solid-state relays intended for performing electrical operations by single step function changes to the state of electric circuits between the OFF

30、-state and the ON-state and vice versa. It is applicable to solid-state relays with rated voltages up to 750 V and with a.c. output current up to 160 A. NOTE Requirements for solid-state relays with d.c. output circuits are under consideration. This standard deals with solid-state relays which are i

31、ntended for incorporation in other products or equipment. As such, solid state relays are considered to be components and this standard defines the basic safety-related and functional requirements for solid-state relays as stand-alone components. Such solid-state relays are incorporated in products

32、or equipment which themselves have to comply with the relevant product and/or application standard(s) to meet their intended application. The following are examples of such applications: general industrial equipment; electrical facilities; electrical machines; electrical appliances; office communica

33、tions; building automation and environmental control; automation and process control; electrical installation engineering; medical engineering; telecommunications; vehicle engineering; transportation engineering; lighting control. Solid state relays are components (not stand alone devices) and as su

34、ch do not perform a direct function. Therefore, no EMC requirements are included in this standard. NOTE This is in line with the European EMC Directive. Where the application of a solid-state relay determines additional requirements such as EMC and overcurrent protection, the solid-state relay shall

35、 be assessed in accordance with the relevant IEC standard(s). Solid-state switching devices with monolithic structures fall within the scope of IEC sub- committee 47E and are not covered in this standard. Semiconductor controllers and contactors fall within the scope of the IEC 60947 series of stand

36、ards Low-voltage switchgear and controlgear developed by IEC subcommittee 17B and are not covered in this standard. Compliance with the requirements of this standard is verified by the type tests indicated. 62314 IEC:2006(E) 7 The object of this standard is to state: the characteristics of solid-sta

37、te relays; the requirements which solid-state relays shall comply with reference to a) their operation and behaviour; b) their dielectric properties; c) the degrees of protection provided by their enclosures, where applicable; the tests verifying that the requirements have been met, and the test met

38、hods to be adopted; the information to be given with the solid-state relay or in the manufacturers documentation. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refere

39、nces, the latest edition of the referenced document (including any amendments) applies. IEC 60038:1983, IEC standard voltages Amendment 1 (1994) Amendment 2 (1997) IEC 60050-195:1998, International Electrotechnical Vocabulary (IEV) Part 195: Earthing and protection against electric shock IEC 60050-4

40、44:2002, International Electrotechnical Vocabulary (IEV) Part 444: Elementary relays IEC 60068-2-1:1990, Environmental testing Part 2: Tests. Tests A: Cold IEC 60068-2-2:1974, Environmental testing Part 2: Tests. Tests B: Dry heat IEC 60068-2-14:1984, Environmental testing Part 2: Tests. Test N: Cha

41、nge of temperature Amendment 1 (1986) IEC 60068-2-20:1979, Environmental testing Part 2: Tests. Test T: Soldering Amendment 2 (1987) IEC 60068-2-78:2001, Environmental testing Part 2-78: Tests Test Cab: Damp heat, steady state IEC 60112:2003, Method for the determination of the proof and the compara

42、tive tracking indices of solid insulating materials IEC 60529, Degrees of protection provided by enclosures (IP Code) IEC 60664-1, Insulation coordination for equipment within low-voltage systems Part 1: Principles, requirements and tests IEC 60664-3:2003, Insulation coordination for equipment withi

43、n low-voltage systems Part 3: Use of coating, potting or moulding for protection against pollution IEC 60695-2-10:2000, Fire hazard testing Part 2-10: Glowing/hot-wire based test methods Glow-wire apparatus and common test procedure 8 62314 IEC:2006(E) IEC 60695-10-2:2003, Fire hazard testing Part 1

44、0-2: Abnormal heat Ball pressure test IEC 60695-11-10:2003, Fire hazard testing Part 11-10: Test flames 50 W horizontal and vertical flame test methods IEC 60999-1:1999, Connecting devices Electrical copper conductors Safety requirements for screw-type and screwless-type clamping units Part 1: Gener

45、al requirements and particular requirements for clamping units for conductors from 0,2 mm 2up to 35 mm 2(included) IEC 61210:1993, Connecting devices Flat quick-connect terminations for electrical copper conductors Safety requirements IEC 61760-1:1998, Surface mounting technology Part 1: Standard me

46、thod for the specification of surface mounting components (SMDs) 3 Terms and definitions For the purposes of this document the terms and definitions given in IEC 60050(444) and the following apply. . 3.1 Terms and definitions related to relays 3.1.1 solid-state relay electrical relay in which the in

47、tended response is produced by electronic, magnetic, optical or other components without mechanical motion IEV 444-01-06 3.1.2 electrical relay device designed to produce sudden and predetermined changes in one or more output circuits when certain conditions are fulfilled in the electrical input cir

48、cuits controlling the device IEV 444-01-01 3.1.3 rated operational voltage U evalue of voltage which determines the application of the solid-state relay and to which the relevant tests and the load categories are referred 3.1.4 rated insulation voltage U ivalue of voltage to which dielectric tests a

49、nd creepage distances are referred 3.1.5 rated impulse withstand voltage U imppeak value of an impulse voltage of prescribed form and polarity which the solid-state relay is capable of withstanding without failure under specified conditions of test and to which the values of the clearances are referred 62314 IEC:2006(E) 9 3.1.6 rated operational curre