IEC 62343-3-1-2016 Dynamic modules - Part 3-1 Performance specification templates - Dynamic channel equalizers《动态模块.第3-1部分 性能规范模块.动态通道均衡器》.pdf

1、 IEC 62343-3-1 Edition 2.0 2016-04 INTERNATIONAL STANDARD Dynamic modules Part 3-1: Performance specification templates Dynamic channel equalizers IEC 62343-3-1:2016-04(en) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2016 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified

2、, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IE

3、C copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Sw

4、itzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is k

5、ept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards,

6、 Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also g

7、ives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.or

8、g The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 0

9、00 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wis

10、h to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 62343-3-1 Edition 2.0 2016-04 INTERNATIONAL STANDARD Dynamic modules Part 3-1: Performance specification templates Dynamic channel equalizers INTERNATIONAL ELECTROTEC

11、HNICAL COMMISSION ICS 33.180.20 ISBN 978-2-8322-3321-4 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. 2 IEC 62343-3-1:2016 IEC 2016 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope 6 2 Normativ

12、e references. 6 3 Terms and definitions 7 4 Test report. 7 5 Reference components 7 6 Performance requirements . 7 6.1 Dimensions . 7 6.2 Sample size 7 6.3 Test details and requirements 7 Bibliography . 10 Table 1 Tests and requirements . 8 IEC 62343-3-1:2016 IEC 2016 3 INTERNATIONAL ELECTROTECHNICA

13、L COMMISSION _ DYNAMIC MODULES Part 3-1: Performance specification templates Dynamic channel equalizers FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The o

14、bject of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifica

15、tions (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations li

16、aising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters expr

17、ess, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Commit

18、tees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Nationa

19、l Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does no

20、t provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have t

21、he latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoeve

22、r, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publication

23、s is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard

24、IEC 62343-3-1 has been prepared by subcommittee 86C: Fibre optic systems and active devices, of IEC technical committee 86: Fibre optics. This second edition cancels and replaces the first edition published in 2010. This edition constitutes a technical revision. This edition includes the following s

25、ignificant technical change with respect to the previous edition: modification of terms and definitions and references. 4 IEC 62343-3-1:2016 IEC 2016 The text of this standard is based on the following documents: FDIS Report on voting 86C/1370/FDIS 86C/1372/RVD Full information on the voting for the

26、 approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62343 series, published under the general title Dynamic modules, can be found on the IEC w

27、ebsite. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by

28、 a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IEC 62343-3-1:2016 IEC 2016 5 INTRODUCTION A dynamic channel equalizer (DCE) is used to compensate and equalize the variations in channel power spectrum as the optical channels propagate through DW

29、DM networks. A typical DCE module is an electrically controlled two port device, which controls the time varying power levels of multichannel input signals such that, at the output channel, powers are nominally equalized. 6 IEC 62343-3-1:2016 IEC 2016 DYNAMIC MODULES Part 3-1: Performance specificat

30、ion templates Dynamic channel equalizers 1 Scope This part of IEC 62343 provides a performance specification template for the dynamic channel equalizer (DCE). The object of this performance specification template is to provide a framework for the preparation of detail specifications on the product o

31、r performance of dynamic channel equalizers. Additional specification parameters may be included for product specifications or performance specifications. However, specification parameters specified in this standard should not be removed from the product specifications or performance specifications.

32、 Technical information regarding dynamic channel equalizers and their applications in DWDM systems is described in IEC TR 62343-6-1. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated r

33、eferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-2-14, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-14: Tests High optical power IE

34、C 61300-3-2, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-2: Examinations and measurements Polarization dependent loss in a single-mode fibre optic device IEC 61300-3-6, Fibre optic interconnecting devices and passive components Basic test a

35、nd measurement procedures Part 3-6: Examinations and measurements Return loss IEC 61300-3-29, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-29: Examinations and measurements Spectral transfer characteristics of DWDM devices IEC 61300-3-32, Fi

36、bre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-32: Examinations and measurements Polarization mode dispersion measurement for passive optical components IEC 61300-3-38, Fibre optic interconnecting devices and passive components Basic test and me

37、asurement procedures Part 3-38: Examinations and measurements Group delay, chromatic dispersion and phase ripple IEC 61753-021-2, Fibre optic interconnecting devices and passive components performance standard Part 021-2: Grade C/3 single-mode fibre optic connectors for category C Controlled environ

38、ment IEC 62343, Dynamic modules General and guidance IEC 62343-3-1:2016 IEC 2016 7 ITU-T Recommendation G.694.1, Spectral grids for WDM applications: DWDM frequency grid 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 62343 apply. 4 Test report Fully

39、 documented test reports and supporting evidence shall be prepared and be available for inspections as evidence that the tests have been carried out and complied with. 5 Reference components The testing for DCE components does not require the use of reference components. 6 Performance requirements 6

40、.1 Dimensions Dimensions shall comply with either an appropriate IEC interface standard, or with those given in the manufacturers drawings, where the IEC interface standard does not exist or cannot be used. 6.2 Sample size The test sample size and sequencing requirements for the module components sh

41、all be defined in the relevant specification. 6.3 Test details and requirements The requirements are given only for non-connectorized DCE devices. For connectorized components, the connector performances shall be in compliance with IEC 61753-021-2. A minimum length of fibre or cable of 1,5 m per por

42、t shall be included in all climatic and environmental tests. The channel spacings, unless otherwise specified, shall be in accordance with ITU-T Recommendation G.694.1. Environmental tests shall be measured for a single input/output port combination. The test details and requirements are given in Ta

43、ble 1. 8 IEC 62343-3-1:2016 IEC 2016 Table 1 Tests and requirements No. Test parameters Unit Details 1 Insertion loss dB Over the operating wavelength range IEC 61300-3-29 Source: The source shall be tuneable over the operating wavelength range and shall have a spectral width of 1 GHz The source sta

44、bility shall be 0,25 GHz The source output shall be unpolarized Detector: The linearity of the detector shall be within 0,05 dB The spectral response shall be matched to the source The dynamic range shall be consistent with the attenuation values to be measured The maximum attenuation value specifie

45、d applies to any combination of input/output ports 2 In band extinction ratio dB Method under consideration 3 Out of band attenuation dB Method under consideration 4 Return loss (branching device method) dB Class W IEC 61300-3-6 Branching device: The nominal splitting ratio shall be 50/50 The direct

46、ivity shall be 60 d B Source: The central wavelength shall be 1 550 nm 20 nm The power stability of the light source shall be better than 0,05 dB over the measuring period Detector: The linearity of the detector shall be within 0,05 dB The detector sensitivity shall be -80 dBm All ports not under te

47、st shall be terminated to avoid unwanted back reflections contributing to the measurement 5 Polarization dependent loss dB IEC 61300-3-2, Method 1 Other details shall be the same as in test no. 1 The polarization dependant loss shall be measured between any input/output port combination 6 Polarizati

48、on mode dispersion ps IEC 61300-3-32 Other details shall be the same as in test no. 1 The polarization mode dispersion shall be measured between any input/output port combination 7 Output channel non- uniformity dB IEC 61300-3-29 8 Input channel non- uniformity dB IEC 61300-3-29 9 Ripple dB IEC 6130

49、0-3-29 10 Channel frequency range GHz Method under consideration 11 Channel response time s Method under consideration 12 Channel spacing GHz Method under consideration 13 Chromatic dispersion ps/nm IEC 61300-3-38 IEC 62343-3-1:2016 IEC 2016 9 No. Test parameters Unit Details 14 Channel crosstalk dB IEC 61300-3-29 15 Adjacent channel attenuation crosstalk dB IEC 61300-3-29 16 Maximum input power dBm IEC 61300-2-14 10 IEC 62343-3-1:2