IEC 62642-1-2010 Alarm systems - Intrusion and hold-up systems - Part 1 System requirements《报警系统.入侵和拦截系统.第1部分 系统需求》.pdf

1、 IEC 62642-1 Edition 1.0 2010-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Alarm systems Intrusion and hold-up systems Part 1: System requirements Systmes dalarme Systmes dalarme contre lintrusion et les hold-up Partie 1: Exigences systme IEC 62642-1:2010 THIS PUBLICATION IS COPYRIGHT PROTECTED Co

2、pyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member N

3、ational Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rser

4、vs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur.

5、Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email

6、: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publica

7、tions is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, t

8、ext, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by em

9、ail. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online.

10、Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electr

11、otechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. V

12、euillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfren

13、ce, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues.

14、 Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egale

15、ment appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl

16、.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62642-1 Edition 1.0 2010-06 INTERNATIONAL STANDARD NORME INTERNATIONALE Alarm systems Intrusion and hold-up systems Part 1: System requirements Systmes dalarme Systmes dalarme contre lintrusion et les hold-up Partie 1: Exigences systme INTERNATIONAL ELEC

17、TROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE X ICS 13.320 PRICE CODE CODE PRIX ISBN 978-2-88910-970-8 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 62642-1 IEC:2010 CONTENTS FOREWORD.5 INTRO

18、DUCTION.7 1 Scope.9 2 Normative references9 3 Terms, definitions and abbreviations.10 3.1 Terms and definitions 10 3.2 Abbreviations.17 4 System functions 17 5 System components17 6 Security grading18 7 Environmental classification18 7.1 General .18 7.2 Environmental Class I Indoor 19 7.3 Environmen

19、tal Class II Indoor General .19 7.4 Environmental Class III Outdoor Sheltered or indoor extreme conditions.19 7.5 Environmental Class IV Outdoor General .19 8 Functional requirements19 8.1 Detection of intruders, triggering, tampering and the recognition of faults .19 8.1.1 Intruder detection.19 8.1

20、.2 Hold-up device triggering 20 8.1.3 Tamper detection.20 8.1.4 Recognition of faults 20 8.2 Other functions20 8.2.1 Masking.20 8.2.2 Movement detector range reduction .21 8.3 Operation 21 8.3.1 Access levels.21 8.3.2 Authorisation .22 8.3.3 Setting and unsetting .23 8.3.4 Setting.23 8.3.5 Preventio

21、n of setting 23 8.3.6 Overriding prevention of setting24 8.3.7 Set state24 8.3.8 Unsetting.25 8.3.9 Restoring.25 8.3.10 Inhibit 26 8.3.11 Isolate .26 8.3.12 Test.26 8.3.13 Other functions 26 8.4 Processing 26 8.4.1 Intruder signals or messages .26 8.4.2 Hold-up signals or messages .27 8.4.3 Tamper s

22、ignals or messages .27 8.4.4 Fault signals or messages .27 8.4.5 Masking signals or messages 27 8.4.6 Reduction of range signals or messages 27 62642-1 IEC:2010 3 8.5 Indications.29 8.5.1 General .29 8.5.2 Availability of indications 30 8.5.3 Cancelling indications 30 8.5.4 Indication Intrusion dete

23、ctors 30 8.6 Notification 31 8.7 Tamper security.32 8.7.1 Tamper protection32 8.7.2 Tamper detection.33 8.7.3 Monitoring of substitution .33 8.7.4 Monitoring of substitution Timing requirements34 8.8 Interconnections 34 8.8.1 General .34 8.8.2 Availability of interconnections .34 8.8.3 Monitoring of

24、 interconnections35 8.8.4 Verification 35 8.8.5 Security of communication .35 8.8.6 Signals or messages to be generated.36 8.9 I any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations l

25、iaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters exp

26、ress, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Commi

27、ttees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC Nation

28、al Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does n

29、ot provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have

30、the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoev

31、er, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publicatio

32、ns is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard

33、 IEC 62642-1 has been prepared by IEC technical committee 79: Alarm and electronic security systems. This standard is based on EN 50131-1 (2006) and its Amendment 1 (2009). The text of this standard is based on the following documents: FDIS Report on voting 79/280/FDIS 79/299/RVD Full information on

34、 the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 6 62642-1 IEC:2010 A list of all parts of the IEC 62642 series can be found, under the general title A

35、larm systems Intrusion and hold-up systems, on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this d

36、ate, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 62642-1 IEC:2010 7 INTRODUCTION This standard is part of the IEC 62642 series of International Standards and Technical Specifications “Alarm systems Intrusion and hold-up systems”, written to include the

37、following parts: Part 1 System requirements Part 2-2 Intrusion detectors Passive infrared detectors Part 2-3 Intrusion detectors Microwave detectors Part 2-4 Intrusion detectors Combined passive infrared / Microwave detectors Part 2-5 Intrusion detectors Combined passive infrared / Ultrasonic detect

38、ors Part 2-6 Intrusion detectors Opening contacts (magnetic) Part 2-71 Intrusion detectors Glass break detectors Acoustic Part 2-72 Intrusion detectors Glass break detectors Passive Part 2-73 Intrusion detectors Glass break detectors Active Part 3 Control and indicating equipment Part 4 Warning devi

39、ces Part 5-3 Requirements for interconnections equipment using radio frequency techniques Part 6 Power supplies Part 7 Application guidelines Part 8 Security fog devices This International Standard applies to Intrusion and Hold-up Alarm Systems (I&HAS). The standard is also intended to apply to Intr

40、uder Alarm Systems (IAS) which include only intrusion detectors and to Hold-up Alarm Systems (HAS) which include only hold-up devices. This International Standard is a specification for Intrusion and Hold-up Alarm Systems installed in buildings, it includes four security grades and four environmenta

41、l classes. The purpose of an I&HAS is to enhance the security of the supervised premises. To maximise its effectiveness an I&HAS should be integrated with appropriate physical security devices and procedures. This is particularly important to higher grade I&HAS. This standard is intended to assist i

42、nsurers, intruder alarm companies, customers and the police in achieving a complete and accurate specification of the supervision required in particular premises, but it does not specify the type of technology, the extent or degree of detection, nor does it necessarily cover all of the requirements

43、for a particular installation. All references to the requirements for I&HAS refer to basic minimum requirements and the designers of such installed I&HAS should take into account the nature of the premises, the value of the contents, the degree of risk of intrusion, the threat to personnel and any o

44、ther factors which may influence the choice of grade and content of an I&HAS. Recommendations for design, planning, operation, installation and maintenance are given in Application Guidelines EN/TS 50131-7. This standard is not intended to be used for testing individual I&HAS components. Requirements for testing individual I&HAS components are given in the relevant component standards.