IEC IEEE 60076-57-1202-2017 Power transformers - Part 57-1202 Liquid immersed phase-shifting transformers《电力变压器 第57-1202部分 液浸相位变换器》.pdf

1、 IEC/IEEE 60076-57-1202 Edition 1.0 2017-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Power transformers Part 57-1202: Liquid immersed phase-shifting transformers Transformateurs de puissance Partie 57-1202: Transformateurs dphaseurs immergs dans un liquide IEC/IEEE 60076-57-1202:2017-05(en-fr) co

2、lour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2017 IEC, Geneva, Switzerland Copyright 2017 IEEE All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and

3、 microfilm, without permission in writing being secured. Requests for permission to reproduce should be addressed to either IEC at the address below or IECs member National Committee in the country of the requester or from IEEE. IEC Central Office Institute of Electrical and Electronics Engineers, I

4、nc. 3, rue de Varemb 3 Park Avenue CH-1211 Geneva 20 New York, NY 10016-5997 Switzerland United States of America Tel.: +41 22 919 02 11 stds.iprieee.org Fax: +41 22 919 03 00 www.ieee.org infoiec.ch www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global o

5、rganization that prepares and publishes International Standards for all electrical, electronic and related technologies. About the IEEE IEEE is the worlds largest professional association dedicated to advancing technological innovation and excellence for the benefit of humanity. IEEE and its members

6、 inspire a global community through its highly cited publications, conferences, technology standards, and professional and educational activities. About IEC/IEEE publications The technical content of IEC/IEEE publications is kept under constant review by the IEC and IEEE. Please make sure that you h

7、ave the latest edition, a corrigendum or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents

8、. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publication

9、s. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electri

10、cal terms containing 20 000 terms and definitions in English and French, with equivalent terms in 16 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French ex

11、tracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further a

12、ssistance, please contact the Customer Service Centre: csciec.ch. IEC/IEEE 60076-57-1202 Edition 1.0 2017-05 INTERNATIONAL STANDARD NORME INTERNATIONALE Power transformers Part 57-1202: Liquid immersed phase-shifting transformers Transformateurs de puissance Partie 57-1202: Transformateurs dphaseurs

13、 immergs dans un liquide INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE ICS 29.180 ISBN 978-2-8322-4258-2 Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publicatio

14、n via un distributeur agr. Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale colour inside 2 IEC/IEEE 60076-57-1202:2017 IEC/IEEE 2017 CONTENTS FOREWORD . 5 1 Scope 7 2 Normative references 7 2.1 IEC references 7 2.2 I

15、EEE references 7 3 Terms and definitions 8 4 Use of normative references 11 5 Service conditions . 11 5.1 General . 11 5.2 Usual service conditions . 11 5.2.1 Switching arrangement 11 5.2.2 Power flow . 11 5.2.3 Operation with two or more PSTs in series or parallel 11 5.2.4 Phase unbalance . 12 5.2.

16、5 Surge protection 12 6 Rating and general requirements . 12 6.1 Rated power . 12 6.2 Loading at other than rated conditions 12 6.3 Specification of buck capability . 12 6.4 Cooling modes 13 6.5 Short circuit impedance and load phase angle capability . 13 6.5.1 Specification 13 6.5.2 Short circuit i

17、mpedance for asymmetric designs 13 6.6 Neutral earthing (grounding) . 13 6.7 Rated voltage . 13 6.8 Voltage variation and asymmetric design 13 6.9 Rated frequency . 14 6.10 Operation at higher than rated voltage and/or at other than rated frequency . 14 6.11 Highest voltage for equipment and dielect

18、ric test levels 14 6.12 Taps . 14 6.13 Sound level . 14 6.14 Transport 14 7 Construction 14 7.1 General . 14 7.2 Liquid-filled connections between tanks 15 7.3 Liquid insulation and preservation system . 15 7.4 Alignment between tanks 15 7.5 Core and core frame earthing arrangements . 16 7.6 Test co

19、nnections . 16 8 Short circuit capability . 16 9 Connection phase displacement symbols . 16 9.1 General . 16 9.2 Special symbols for PSTs . 16 9.3 Clock number notation 17 9.4 Examples 17 9.4.1 Single core phase shifting transformers . 17 IEC/IEEE 60076-57-1202:2017 3 IEC/IEEE 2017 9.4.2 Two core ph

20、ase shifting transformers 19 9.4.3 Transformers incorporating a phase shifting element . 21 10 Rating plates (nameplates) 22 11 Terminal markings and phase rotation . 23 12 Information to be provided by the manufacturer . 23 13 Tests . 24 13.1 General . 24 13.2 Routine tests. 24 13.3 Type (design) t

21、ests . 24 13.4 Special tests . 24 13.5 Winding resistance 25 13.6 Measurement of voltage ratio, phase angle and check of phase displacement 25 13.7 Measurement of short-circuit impedance and load loss . 25 13.8 Temperature-rise test 26 13.9 Measurement of no-load loss and current . 26 13.10 Determin

22、ation of sound level . 26 13.10.1 General . 26 13.10.2 For PSTs with one combined cooling system . 26 13.10.3 For PSTs with separate exciting and series unit cooling systems . 27 13.11 Measurement of zero sequence impedance 27 13.12 Dielectric tests 27 13.12.1 General . 27 13.12.2 Induced voltage te

23、st with partial discharge measurement (IVPD) . 28 13.12.3 Switching impulse test (SI) 28 13.12.4 Lightning impulse test 28 13.12.5 Lightning impulses applied to multiple line terminals simultaneously (LIMT) . 29 13.13 Tests on on-load tap-changers operation test . 29 13.14 Leak testing with pressure

24、 30 13.15 Vacuum deflection test 30 13.16 Pressure deflection test 30 14 Tolerances 30 14.1 General . 30 14.2 Tolerance for impedance and phase angle 30 Annex A (informative) Check list of information to be provided with enquiry and order . 32 A.1 Rating and general data 32 A.1.1 Normal information

25、32 A.1.2 Special information 33 A.2 Parallel operation 34 Annex B (informative) Behaviour of a phase shifting transformer with non-symmetrical fault currents. 35 Annex C (informative) Example specification of buck capability . 37 Annex D (informative) Additional noise measurements . 38 Annex E (info

26、rmative) Calculation of phase angle under load . 40 Annex F (informative) Additional information on advance-retard switch 44 F.1 Principle . 44 F.2 Classification within the international standardization system 44 4 IEC/IEEE 60076-57-1202:2017 IEC/IEEE 2017 F.3 Requirements according to IEC 60214-1

27、and IEEE Std C57.131 . 44 Bibliography 45 Figure 1 Example A: DS0-3/9 18 Figure 2 Example B: PS0-3/9 18 Figure 3 Example C: DA0-3 19 Figure 4 Example D: YNyn/IIId S0-3/9 . 20 Figure 5 Example E: YNyn+d/IIId A0-3/9 . 20 Figure 6 Example F: YNa0yn/dIII A0-3/9 . 21 Figure 7 Example G: V A0-2/8. 22 Figu

28、re B.1 PST with single phase fault and surge protection 36 Figure E.1 Phase angle diagram for a PST under load where 0 0 and L0 and L 0 . 41 Figure E.4 Phase angle diagram for a PST under load where 00 . 41 Table C.1 Required PST capability in buck operation . 37 Table D.1 Combinations of sound leve

29、l measurements needed to represent different loading conditions . 39 IEC/IEEE 60076-57-1202:2017 5 IEC/IEEE 2017 POWER TRANSFORMERS Part 57-1202: Liquid immersed phase-shifting transformers FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardizatio

30、n comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes Internationa

31、l Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in thi

32、s preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEEE Standards documents are developed within IEEE Societies and Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Boa

33、rd. IEEE develops its standards through a consensus development process, approved by the American National Standards Institute, which brings together volunteers representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily members of IEEE and serve without

34、 compensation. While IEEE administers the process and establishes rules to promote fairness in the consensus development process, IEEE does not independently evaluate, test, or verify the accuracy of any of the information contained in its standards. Use of IEEE Standards documents is wholly volunta

35、ry. IEEE documents are made available for use subject to important notices and legal disclaimers (see http:/standards.ieee.org/IPR/disclaimers.html for more information). IEC collaborates closely with IEEE in accordance with conditions determined by agreement between the two organizations. This Dual

36、 Logo International Standard was jointly developed by the IEC and IEEE under the terms of that agreement. 2) The formal decisions of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representati

37、on from all interested IEC National Committees. The formal decisions of IEEE on technical matters, once consensus within IEEE Societies and Standards Coordinating Committees has been reached, is determined by a balanced ballot of materially interested parties who indicate interest in reviewing the p

38、roposed standard. Final approval of the IEEE standards document is given by the IEEE Standards Association (IEEE-SA) Standards Board. 3) IEC/IEEE Publications have the form of recommendations for international use and are accepted by IEC National Committees/IEEE Societies in that sense. While all re

39、asonable efforts are made to ensure that the technical content of IEC/IEEE Publications is accurate, IEC or IEEE cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undert

40、ake to apply IEC Publications (including IEC/IEEE Publications) transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC/IEEE Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5

41、) IEC and IEEE do not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC and IEEE are not responsible for any services carried out by independent certification bodies. 6) All users

42、should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or IEEE or their directors, employees, servants or agents including individual experts and members of technical committees and IEC National Committees, or volunteers of IEEE Societies and the Sta

43、ndards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board, for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or relia

44、nce upon, this IEC/IEEE Publication or any other IEC or IEEE Publications. 8) Attention is drawn to the normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that i

45、mplementation of this IEC/IEEE Publication may require use of material covered by patent rights. By publication of this standard, no position is taken with respect to the existence or validity of any patent rights in connection therewith. IEC or IEEE shall not be held responsible for identifying Ess

46、ential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patent Claims or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are re

47、asonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. 6 IEC/IEEE 60076-57-1202:2017 IEC/IEEE 2017 International Standard IEC/IEEE 60076-5

48、7-1202 has been prepared by IEC technical committee 14: Power transformers, in cooperation with the Transformers Committee of the IEEE Power & Energy Society 1 , under the IEC/IEEE Dual Logo Agreement. This publication is published as an IEC/IEEE Dual Logo standard. The text of this standard is base

49、d on the following IEC documents: FDIS Report on voting 14/892/FDIS 14/902/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The IEC Technical Committee and IEEE Technical Committee have decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC websit