IEC 60384-11-1-2008 Fixed capacitors for use in electronic equipment - Part 11-1 Blank detail specification - Fixed polyethylene terephthalate film dielectric m.pdf

1、 IEC 60384-11-1 Edition 2.0 2008-02 INTERNATIONAL STANDARD Fixed capacitors for use in electronic equipment Part 11-1: Blank detail specification Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Assessment level EZ IEC 60384-11-1:2008(E) QC 300101 THIS PUBLICATION IS COPYR

2、IGHT PROTECTED Copyright 2008 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC

3、 or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Centra

4、l Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies

5、. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enable

6、s you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month al

7、l new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also kn

8、own as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11

9、Fax: +41 22 919 03 00 IEC 60384-11-1 Edition 2.0 2008-02 INTERNATIONAL STANDARD Fixed capacitors for use in electronic equipment Part 11-1: Blank detail specification Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Assessment level EZ INTERNATIONAL ELECTROTECHNICAL COMMIS

10、SION M ICS 31.060.30 PRICE CODE ISBN 2-8318-9609-6 QC 300101 2 60384-11-1 IEC:2008(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 11-1: Blank detail specification Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Assessm

11、ent level EZ FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardi

12、zation in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation i

13、s entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the

14、 International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects

15、since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical cont

16、ent of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possib

17、le in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipme

18、nt declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC

19、National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attenti

20、on is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC

21、shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-11-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This second edition cancels and replaces the first edition published in 1988 and cons

22、titutes a minor revision related to tables, figures and references. The text of this standard is based on the following documents: CDV Report on voting 40/1840/CDV 40/1865/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above

23、 table. 60384-11-1 IEC:2008(E) 3 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The QC number that appears on the front cover of this publication is the specification number in the IECQ Quality Assessment System for Electronic Components (IECQ). The list of all

24、parts of the IEC 60384 series, under the (new) general title Fixed capacitors for use in electronic equipment, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under

25、“http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. 4 60384-11-1 IEC:2008(E) FIXED CAPACITORS FOR USE I

26、N ELECTRONIC EQUIPMENT Part 11-1: Blank detail specification Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Assessment level EZ INTRODUCTION Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains re

27、quirements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. In the preparation of detail specifications, the content of 1

28、.4 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification 1 The “International Electrotechnical Commission“ or the

29、 National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national generic spec

30、ification. 4 The IEC number of the blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construction (when applicable). NOTE When the capacitor is not designed for use in printed-board applications, this shall be clearly

31、 stated in the detail specification in this position. 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. 8 Ap

32、plication or group of applications covered and/or assessment level. NOTE The assessment level(s) to be used in a detail specification are selected from 3.5.4 of the sectional specification. This implies that one blank detail specification may be used in combination with several assessment levels, pr

33、ovided the grouping of the tests does not change. 9 Reference data on the most important properties, to allow comparison between the various capacitor types. 60384-11-1 IEC:2008(E) 5 1 IEC 60384-11-1-XXX 2 QC 300101-XXX IEC 60384-11-1 4 QC 300101 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDAN

34、CE WITH: 3 FIXED POLYETHYLENE- 5 TEREPHTHALATE FILM DIELECTRIC METAL FOIL D.C. CAPACITORS 6 Outline drawing: (see Table 1) .angle projection 7 Other shapes are permitted within the dimensions given. Assessment level(s): EZ 8 For Notes 1 to 9 see preceding page. Information on the availability of com

35、ponents qualified to this detail specification is given in the Qualified Products List. (9) 1 General data 1.1 Recommended method(s) of mounting (to be inserted) See IEC 60384-11, 1.4.2. 1.2 Dimensions Table 1 Case size reference and dimensions Dimensions mm Case size reference L H d . NOTE 1 When t

36、here is no case size reference, Table 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Table 1. NOTE 2 The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 6 60384-11-1 IEC:2008(E) 1.3 Ratings and characteristics Capacitance

37、range (see Table 2) Tolerance on rated capacitance Rated voltage (see Table 2) Category voltage (if applicable) (see Table 2) Climatic category Rated temperature Max. a.c. voltage (if applicable) Tangent of loss angle (tan ) Insulation resistance Table 2 Values of capacitance and of voltage related

38、to case sizes Rated voltage Category voltage aCase size Case size Case size Case size Rated capacitance (in nF and/or F) aIf different from the rated voltage. 1.4 Normative references The following referenced documents are indispensable for the application of this document. For dated references, onl

39、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60384-11, Fixed capacitors for use in electronic equipment Part 11: Sectional specification Fixed polyethylene-terephthalate film dielectric metal foil d.c. capa

40、citors 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of 1.6 of IEC 60384-11. The details of the marking of the component and package shall be given in full in the detail specification. 1.6 Ordering information Orders for capacitors covered by t

41、his specification shall contain, in clear or in coded form, the following minimum information: a) rated capacitance; b) tolerance on rated capacitance; c) rated d.c. voltage; d) number and issue reference of the detail specification and style reference; e) packaging instructions. 60384-11-1 IEC:2008

42、(E) 7 1.7 Certified records of released lots Required/not required. 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic and/or sectional specification NOTE Additions or increased requirements should be spec

43、ified only when essential. Table 3 Other characteristics This table is to be used for defining characteristics which are additional to, or more severe than, those given in the sectional specification. 2 Inspection requirements 2.1 Procedures 2.1.1 For qualification approval, the procedures shall be

44、in accordance with 3.4 of the sectional specification, IEC 60384-11. 2.1.2 For quality conformance inspection, the test schedule (Table 4) includes sampling, periodicity, severities and requirements. The formation of inspection lots is covered by 3.5.1 of IEC 60384-11. Table 4 Test schedule for qual

45、ity conformance inspection Number of specimens and number of non- conforming items cSubclause number and test aD or ND cConditions of testaIL n c Performance requirements aGroup A inspection (lot-by-lot) Sub-group A0 4.2.2 Capacitance Within specified tolerance 4.2.3 Tangent of lossangle (tan ) Freq

46、uency : 1 kHz for all capacitance values As in 4.2.3.2 4.2.1 Voltage proof (Test A) Method: Measuring point 1a No breakdown or flashover 4.2.4 Insulationresistance (Test A) ND Measuring point 1a 100% dAs in 4.2.4.2 S-3 Group A inspection (lot-by-lot) Sub-group A1 4.1 Visual examination ND b 0 As in

47、4.1 Legible marking and as specified in 1.5 of this specification Sub-group A2 4.1 Dimensions(gauging) eND S-3 b0 As specified in Table 1 of this specification 8 60384-11-1 IEC:2008(E) Table 4 Test schedule for quality conformance inspection (continued) Number of specimens and number of non- conform

48、ing items cSubclause number and test aD or ND cConditions of testaIL n c Performance requirements aGroup B inspection (lot-by-lot) Sub-group B1 4.5 Solderability (ifapplicable) Without ageing Method: Good tinning as evidenced by free flowing of the solder with wetting of the termina- tions or solder

49、 shall flow within . s, as applicable 4.14 Solvent resistance of the marking (if applicable ND Solvent: Solvent temperature: Method 1 Rubbing material: cotton wool Recovery: S-3 b0 Legible marking aSubclause numbers of tests and performance requirements refer to the sectional specification, IEC 60384-11, and Clause 1of this specification. bNumber to be tested: sample size as directly allotted to the code letter f