IEC 60938-2-1-1999 Fixed inductors for electromagnetic interference suppression - Part 2-1 Blank detail specification - Inductors for which safety tests are req.pdf

1、 IEC 60938-2-1 Edition 1.0 1999-10 INTERNATIONAL STANDARD NORME INTERNATIONALE Fixed inductors for electromagnetic interference suppression Part 2-1: Blank detail specification Inductors for which safety tests are required Assessment level D Inductances fixes dantiparasitage Partie 2-1: Spcification

2、 particulire cadre Inductances ncessitant des essais de scurit Niveau dvaluation D IEC 60938-2-1:1999-10(EN-FR) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 1999 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized i

3、n any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rig

4、hts to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun pr

5、ocd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes

6、 ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global orga

7、nization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amend

8、ment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and i

9、Pad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpubli

10、shed Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and d

11、efinitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and De

12、finitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the

13、 Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications I

14、EC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques su

15、r les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critr

16、es (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disp

17、onible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. E

18、galement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres a

19、ntrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 60938-2-1 Edition 1.0 1999-10 INTERNATIONAL STANDARD NORME INT

20、ERNATIONALE Fixed inductors for electromagnetic interference suppression Part 2-1: Blank detail specification Inductors for which safety tests are required Assessment level D Inductances fixes dantiparasitage Partie 2-1: Spcification particulire cadre Inductances ncessitant des essais de scurit Nive

21、au dvaluation D INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE L ICS 29.100.10; 31.020 PRICE CODE CODE PRIX ISBN 978-2-8322-1335-3 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale

22、 Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 60938-2-1 IEC:1999 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SU

23、PPRESSION Part 2-1: Blank detail specification Inductors for which safety tests are required Assessment level D FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees

24、). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; a

25、ny IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Sta

26、ndardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee

27、has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sens

28、e. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standa

29、rd shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that some of the elements of this Inter

30、national Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60938-2-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This bilingual version

31、2014-01) corresponds to the monolingual English version, published in 1999-10. The text of this standard is based on the following documents: FDIS Report on voting 40/1112/FDIS 40/1138/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicate

32、d in the above table. The French version of this standard has not been voted upon. 60938-2-1 IEC:1999 3 This publication has been drafted in accordance with the ISO/IEC Directives, Part 3. The committee has decided that this publication remains valid until 2005. At this date, in accordance with the

33、committees decision, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. 4 60938-2-1 IEC:1999 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION Part 2-1: Blank detail specification Inductors for which safety tests are required Assessment level D INTR

34、ODUCTION Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requirements for style, layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as b

35、eing in accordance with IEC specifications nor shall they so be described. In the preparation of detail specifications the content of 1.4 of the sectional specification shall be taken into account. The numbers between square brackets on the first page of the detail specification correspond to the fo

36、llowing information which shall be inserted in the position indicated. Identification of the detail specification 1 The “International Electrotechnical Commission“ or the National Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number

37、 of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national generic specification. 4 The IEC number of the blank detail specification. Identification of the inductor 5 A short description of the type of

38、 inductor. 6 Information on typical construction (when applicable). 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail speci

39、fication. 8 Application or group of applications covered and/or assessment level. 9 Reference data on the most important properties, to allow comparison between the various inductor types. 60938-2-1 IEC:1999 5 1 IEC 60938-2-1XX 2 QC XXXXXXXXXXXX ELECTRONIC COMPONENTS OF ASSESSED IEC 60938-2-1 4 QUAL

40、ITY IN ACCORDANCE WITH: QC XXXXXX 3 FIXED INDUCTORS FOR ELECTROMAGNETIC INTERFERENCE SUPPRESSION FOR WHICH SAFETY 5 Outline drawing: (see table 1) TESTS ARE REQUIRED (. angle projection) 7 6 (Other shapes are permitted within the dimensions given) Assessment level: D 8 NOTES 1 to 9 see page 3. 9 Inf

41、ormation on the availability of components qualified to this detail specification is given in the Register of Approvals. 1 General data 1.1 Recommended method(s) of mounting (to be inserted) (See 1.4.3 of IEC 60938-2.) 1.2 Dimensions Table 1 Dimensions related to case size Case size reference or typ

42、e Dimensions mm L W H NOTE 1 When there is no case size reference, the dimensions should be given per type designation. NOTE 2 The dimensions should be given as maximum dimensions or as nominal dimensions with a tolerance. 6 60938-2-1 IEC:1999 1.3 Ratings and characteristics Inductance range (see ta

43、ble 2) Tolerance on rated inductance Rated current (I) range (see table 2) DC resistance (R) (see table 2) Rated voltage Rated temperature Climatic category Category of passive flammability Table 2 Type designation related to values of inductance, rated current and d.c. resistance Type designation r

44、elated to values of inductance, rated current and d.c. resistance L Rper line mH I RA R maxper line 1.4 Related documents Generic specification: IEC 60938-1:(1999), Fixed inductors for electromagnetic interference suppression Part 1: Generic specification Sectional specification: IEC 60938-2:(1999),

45、 Fixed inductors for electromagnetic interference suppression Part 2: Sectional specification 1.5 Marking The marking of the inductor and the package shall be in accordance with the requirements of 1.6 of IEC 60938-2. The details of the marking of the component and packaging shall be given in full i

46、n the detail specification. 1.6 Ordering information Orders for inductors covered by this specification shall contain, in clear or in coded form, the following minimum information: a) type designation; b) rated inductance; c) tolerance on rated inductance; d) rated voltage; e) rated current; f) numb

47、er and issue reference of the detail specification and style reference. 1.7 Certified records of released lots Required/non required. 60938-2-1 IEC:1999 7 1.8 Additional information (not for inspection purposes) 1.9 Additional or increased severities or requirements to those specified in the generic

48、 or sectional specification NOTE Additions or increased requirements should be specified only when essential. Table 3 Other characteristics This table is to be used for defining characteristics which are additional to or more severe than those given in the sectional specification. 2 Inspection requi

49、rements 2.1 Procedures 2.1.1 For qualification approval, the procedure shall be in accordance with 3.4 of IEC 60938-2. 2.1.2 For quality conformance inspection, the test schedule (table 4) includes sampling, periodicity, severities and requirements. The formation of inspection lots is covered by 3.5.1 of the sectional specification. Table 4 Test