IEC 61196-10-1-2014 Coaxial communication cables - Part 10-1 Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric《同轴通.pdf

1、 IEC 61196-10-1 Edition 1.0 2014-09 INTERNATIONAL STANDARD Coaxial communication cables Part 10-1: Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric IEC 61196-10-1:2014-09(en) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerlan

2、d All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of

3、the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax:

4、 +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publicatio

5、ns The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliograp

6、hical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (referen

7、ce number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a m

8、onth by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocab

9、ulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 an

10、d CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 61196-10-1 Edition 1.0 2014-09 INTERNATIONAL STANDARD Coaxial communication cables Part 10-1: Bla

11、nk detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric INTERNATIONAL ELECTROTECHNICAL COMMISSION J ICS 33.120.10 PRICE CODE ISBN 978-2-8322-1863-1 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this pub

12、lication from an authorized distributor. 2 IEC 61196-10-1:2014 IEC 2014 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Guidance for the preparation of detail specifications 5 4 Blank detail specification . 6 Annex A (normative) Maximum attenuation 9 IEC 61196-10-1:2014 IEC 2014 3 INTERNA

13、TIONAL ELECTROTECHNICAL COMMISSION _ COAXIAL COMMUNICATION CABLES Part 10-1: Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all

14、national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Tech

15、nical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory wor

16、k. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2

17、) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommen

18、dations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any e

19、nd user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional public

20、ation shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independ

21、ent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any per

22、sonal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative re

23、ferences cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible f

24、or identifying any or all such patent rights. International Standard IEC 61196-10-1 has been prepared by subcommittee 46A: Coaxial cables, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. The text of this standard is ba

25、sed on the following documents: FDIS Report on voting 46A/1214/FDIS 46A/1233/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4

26、IEC 61196-10-1:2014 IEC 2014 This publication is to be used in conjunction with IEC 61196-1:2005 and IEC 61196-10:2014. A list of all parts in the IEC 61196 series, published under the general title Coaxial communication cables, can be found on the IEC website. The committee has decided that the con

27、tents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual v

28、ersion of this publication may be issued at a later date. IEC 61196-10-1:2014 IEC 2014 5 COAXIAL COMMUNICATION CABLES Part 10-1: Blank detail specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric 1 Scope This part of IEC 61196 applies to coaxial communication cables desc

29、ribed in IEC 61196-10. It specifies the requirements for semi-rigid radio frequency and coaxial cables with solid dielectric and semi-airspace dielectric. These cables are intended for use in microwave and wireless equipment or other signal transmission equipment or units at frequencies above 500 MH

30、z. This part of IEC 61196 is to be read in conjunction with IEC 61196-1 and IEC 61196-10. The blank detail specification determines the layout and style for detail. Detail specifications, based on the blank detail specification, may be prepared by a national organization, a manufacturer or a user. 2

31、 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendm

32、ents) applies. IEC 61196-1:2005, Coaxial communication cables Part 1: Generic specification General, definitions and requirements IEC 61196-10:2014, Coaxial communication cables Part 10: Sectional specification for semi-rigid cables with polytetrafluoroethylene (PTFE) dielectric NOTE Documents which

33、 are needed to achieve the tests according to Clause 4, item 9 or item 10, respectively, are listed in IEC 61196-10. 3 Guidance for the preparation of detail specifications The detail specification shall be written in accordance with the layout of the blank detail specification, which forms part of

34、this standard. NOTE 1 When a characteristic does not apply, then NA (for not applicable) is entered in the appropriate space. NOTE 2 When a characteristic applies but a specific value is not considered necessary, then NS (for not specified) is entered. The numbers shown in brackets in this and the f

35、ollowing pages correspond to the following items of required information, which should be entered in the space provided. 1 Name and address of the organization that has prepared the document 2 IEC document number and date of issue 3 Address of the organization from which the document is available 4

36、Related documents 5 Any other references to the cable, national reference, trade name, etc. 6 Complete description of the cable 6 IEC 61196-10-1:2014 IEC 2014 7 Cable construction 8 Engineering information 9 Parameter to be verified 10 Reference to the relevant subclause of the sectional specificati

37、on 11 Minimum requirements, the values entered shall meet as a minimum the requirements of sectional specification IEC 61196-10 12 Remarks 4 Blank detail specification Title 1 Prepared by: 2 Document No.: Issue: Date: 3 Available from: 4 Generic specification IEC 61196-1 Sectional specification IEC

38、61196-10 5 Additional references: 6 Cable description: a) Cable variant b) Material of inner conductor c) Material of dielectric d) Outer conductor e) Material of sheath (if any) 7 Cable construction: a) Inner conductor Material Diameter (mm) nominal Tolerance (mm): b) Dielectric Material Diameter (

39、mm) nominal Tolerance (mm): c) Outer conductor Material Diameter (mm) nominal Tolerance (mm): . d) Sheath (if any) Material Minimum thickness (mm) Diameter (mm) Tolerance (mm): IEC 61196-10-1:2014 IEC 2014 7 8 Engineering information (reference only): a) Operating temperature range b) Installation t

40、emperature range c) Storage temperature range d) Maximum operating frequency e) Nominal characteristic impedance f) Maximum continue working voltage g) Minimum bending radius (static state) h) Minimum bending radius (dynamic state) i) Nominal weight j) Power rating 9 Parameter 10 Subclause of IEC 61

41、196-10:2014 11 Value 12 Remarks Electrical characteristics 7.2 Continuity 7.2.1 pass Conductor direct current resistance 7.2.2 /km Withstand voltage of dielectric 7.2.3 kV r.m.s. 40 Hz to 60 Hz Withstand voltage of sheath 7.2.4 kV r.m.s. 40 Hz to 60 Hz Insulation resistance 7.2.5 M km 5 000 M km acc

42、ording to IEC 61196-10 Capacitance 7.2.6 Frequency: pF/m Mean characteristic impedance 7.2.7 ( ) 200 MHz Regularity of impedance 7.2.8 Test procedure: Regularity 40 dB resp. 1 % aRelative propagation velocity (velocity ratio) 7.2.9 Frequency: ( ) % Return loss 7.2.10 at MHz dB If necessary, refer to

43、 a table or graph at the end of the detail specification Attenuation 7.2.11 at MHz dB/100 m If necessary, refer to a table or graph at the end of the detail specification Attenuation stability 7.2.12 Intermodulation (IM3) 7.2.13 dBm f 1 = MHz af 2 = MHz a Input power: W Only applicable to 50 cable v

44、ariants Environmental characteristics 7.3 Dimensional stability 7.3.1 ns See IEC 61196-10 Heat behaviour 7.3.2 ns See IEC 61196-10 8 IEC 61196-10-1:2014 IEC 2014 Ageing 7.3.3 NS See IEC 61196-10 Solderability 7.3.4 NS See IEC 61196-10 Resistance to soldering 7.3.5 NS See IEC 61196-10 Mechanical char

45、acteristics 7.4 Visual examination 7.4.1 NS See IEC 61196-10 Dimensional examination 7.4.2 Ovality of dielectric 7.4.3 % 7 % according to IEC 61196-10 Eccentricity of dielectric 7.4.4 % 10 % according to IEC 61196-10 Ovality of sheath 7.4.5 % 7 % according to IEC 61196-10 Adhesion testing 7.4.6 N Be

46、ndability (single bend) b7.4.7 1 cycle No cracks or longitudinal splits in outer conductor Transmission characteristics shall remain within specified tolerances Thermal cycling 7.4.8 Low temperature C min. High temperature C max. Rate of temperature change s Number of cycles Duration of cycle Detail

47、s of sample placement Quality assessment Annex A NS See IEC 61196-10 NS: not specified, i.e. the appropriate requirement in the sectional specification shall apply. aMark NA, if not applicable bFrequencies are not always fixed frequencies and can be a swept over a range. IEC 61196-10-1:2014 IEC 2014 9 Annex A (normative) Maximum attenuation Frequency specified MHz Maximum attenuation: dB/100 m at 20 C 200 800 1 000 _ INTERNATIONAL ELECTROTECHNICAL COMMISSION 3, rue de Varemb PO Box 131 CH-1211 Geneva 20 Switzerland Tel: + 41 22 919 02 11 Fax: + 41 22 919 03 00 infoiec.ch www.iec.ch