IEC 61212-1-2006 Insulating materials - Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes - Part 1 Definitio.pdf

1、 IEC 61212-1 Edition 2.0 2006-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 1: Definitions, designations and general requirements Matriaux isolants Tubes et barres industr

2、iels rigides, ronds, stratifis base de rsines thermodurcissables usages lectriques Partie 1: Dfinitions, dsignations et exigences gnrales IEC 61212-1:2006-03(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2006 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no par

3、t of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyri

4、ght or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni u

5、tilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmen

6、taires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electro

7、technical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that

8、you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other docum

9、ents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publica

10、tions. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and ele

11、ctrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries

12、in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publi

13、cation or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux

14、 technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour

15、consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trou

16、ver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Publ

17、ished dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que le

18、s termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publica

19、tions IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61212-1 E

20、dition 2.0 2006-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 1: Definitions, designations and general requirements Matriaux isolants Tubes et barres industriels rigides,

21、ronds, stratifis base de rsines thermodurcissables usages lectriques Partie 1: Dfinitions, dsignations et exigences gnrales INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE L ICS 29.035.01 PRICE CODE CODE PRIX ISBN 978-2-8322-1597-5 Registered trademark of the Int

22、ernational Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 61212-1:20

23、06 IEC 2006 CONTENTS FOREWORD . 3 INTRODUCTION . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 6 4 Designations and abbreviations 7 4.1 General . 7 4.2 Designation . 7 4.3 Abbreviations 8 4.4 Characteristics of types . 8 5 General requirements Appearance 10 6 Conditions of suppl

24、y . 11 Table 1 Types of industrial laminated round rolled tubes 8 Table 2 Types of industrial laminated round moulded tubes . 9 Table 3 Types of industrial laminated round moulded rods . 10 IEC 61212-1:2006 IEC 2006 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INSULATING MATERIALS INDUSTRIAL RIGID

25、ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES Part 1: Definitions, designations and general requirements FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical com

26、mittees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technic

27、al Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmenta

28、l and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agr

29、eements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use

30、 and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promo

31、te international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indica

32、ted in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach t

33、o IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) an

34、d expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9

35、) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61212-1 has been prepared by IEC technical committee 15: Standard

36、s on specifications for electrical insulating materials. This bilingual version (2014-05) corresponds to the English version, published in 2006-03. This second edition cancels and replaces the first edition published in 1995 and constitutes a technical revision. The main changes from the previous ed

37、ition are as follows: added application use and safety statements. Reformatted document to bring it up to current IEC document format. Method for designation of tubes changed in line with common practice. New types EP GC 23 and PF CC 24 added. Type PF CP 24 removed. 4 IEC 61212-1:2006 IEC 2006 The t

38、ext of this standard is based on the following documents: FDIS Report on voting 15/271/FDIS 15/304/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This

39、 publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A bilingual version of this publication may be issued at a later date. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web sit

40、e under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. The contents of the corrigendum of March 2014 have been included in this copy. IEC 61212-1:2006 IEC 2006 5 INTRODU

41、CTION This International Standard is one of a series which deals with industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes. This series consists of three parts: Part 1: Definitions, designations and general requirements (IEC 61212-1) Part 2: Methods o

42、f test (IEC 61212-2) Part 3: Specifications for individual materials (IEC 61212-3) 6 IEC 61212-1:2006 IEC 2006 INSULATING MATERIALS INDUSTRIAL RIGID ROUND LAMINATED TUBES AND RODS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES Part 1: Definitions, designations and general requirements 1 Scope

43、 This part of IEC 61212 gives the definitions related to the designations to be used for, and the general requirements to be fulfilled by, industrial rigid round laminated tubes and rods for electrical purposes made with any of the following resins as the binder: phenolic, epoxy (epoxide), melamine

44、and silicone. The following reinforcements may be used either singly or in combination: cellulosic paper, woven cotton cloth, woven glass cloth, mica paper. Materials which conform to this specification meet established levels of performance. However, the selection of a material by a user for a spec

45、ific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. Safety warning: It is the responsibility of the user of the methods contained or referred to in this document to ensure that they are used in

46、a safe manner. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61212-2

47、:2006, Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purposes Part 2: Methods of test IEC 61212-3 (all parts): , Insulating materials Industrial rigid round laminated tubes and rods based on thermosetting resins for electrical purpo

48、ses Part 3: Specifications for individual materials 2ISO 472, Plastics Vocabulary 3 Terms and definitions For the purposes of this document, the following definitions, which are taken from ISO 472, apply. 3.1 round laminated rolled tube (as applied to thermosets) tube formed by rolling impregnated l

49、ayers of material on a mandrel between heated pressure rolls, curing in an oven, and then removing the mandrel ISO 472, MOD IEC 61212-1:2006 IEC 2006 7 3.2 round laminated moulded tube (as applied to thermosets) tube formed by rolling impregnated layers of material on a mandrel, curing the assembly in a cylindrical mould under heat and pressure, and then removing the mandrel ISO 47