IEC 61300-2-15-2008 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-15 Tests - Torque strength of co.pdf

1、 IEC 61300-2-15 Edition 2.0 2008-02 INTERNATIONAL STANDARD Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-15: Tests Torque strength of coupling mechanism IEC 61300-2-15:2008(E) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2008 IEC, Geneva

2、, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the

3、 country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office 3, rue de Varemb CH-1211 Geneva

4、20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical co

5、ntent of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria

6、(reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on

7、-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical

8、 Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61300-2-15 Edit

9、ion 2.0 2008-02 INTERNATIONAL STANDARD Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-15: Tests Torque strength of coupling mechanism INTERNATIONAL ELECTROTECHNICAL COMMISSION H ICS 33.180.20 PRICE CODE ISBN 2-8318-9601-0 2 61300-2-15 IEC:2008

10、(E) CONTENTS FOREWORD.3 1 Scope.5 2 Normative references5 3 General description.5 4 Apparatus.5 4.1 Stand 5 4.2 Specimen holder5 4.3 Coupling6 4.4 Coupling shaft .6 4.5 Alignment mechanism6 4.6 Torque applicator and gauge .6 5 Procedure.7 5.1 Preparation of specimens 7 5.2 Pre-conditioning 7 5.3 Spe

11、cimen mounting .7 5.4 Torque loading 7 5.5 Post-test examination 7 6 Severity 7 7 Details to be specified.7 Figure 1 Coupling torque tester 6 61300-2-15 IEC:2008(E) 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PRO

12、CEDURES Part 2-15: Tests Torque strength of coupling mechanism FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international

13、co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referre

14、d to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in t

15、his preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an internatio

16、nal consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable

17、efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publi

18、cations transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval

19、and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual expert

20、s and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Pub

21、lication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Pub

22、lication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61300-2-15 has been prepared by sub-committee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibr

23、e optics. This second edition cancels and replaces the first edition published in 1995. It constitutes a technical revision. Specific technical changes from the previous edition include reexamination of the pre-conditioning and rewriting of the entire composition according to the latest IEC Directiv

24、es. 4 61300-2-15 IEC:2008(E) The text of this standard is based on the following documents: CDV Result of voting 86B/2539/CDV 86B/2650/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. A list of all parts of IEC 61

25、300 series, published under the general title Fibre optic interconnecting devices and passive components Basic test and measurement procedures, can be found on the IEC website. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the con

26、tents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bi

27、lingual version of this publication may be issued at a later date. 61300-2-15 IEC:2008(E) 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-15: Tests Torque strength of coupling mechanism 1 Scope This part of IEC 61300 applies an overload torqu

28、e to twist-type coupling mechanisms. It is applicable to threaded or bayonet-twist type coupling mechanisms. It can be used to ensure that the coupling mechanism of a connector set or connector-device combination will withstand the torsional loads likely to be applied during normal service. 2 Normat

29、ive references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-3-1: Fibre optic interco

30、nnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination 3 General description A torsional load is smoothly applied to a mated connector set or connector-device combination in a manner that will over-torque threaded or b

31、ayonet twist-type coupling mechanisms. The torque is normally applied between the connector plug and the adapter or between the connector plug and the device being tested. 4 Apparatus The test apparatus shall be capable of applying a torque, either manually or automatically, to a threaded or bayonet

32、 coupling nut while the adapter or device is held in place. An example of a test apparatus is shown in Figure 1. Some or all of the following apparatus components will be required. 4.1 Stand Use a stand capable of ensuring that the specimen and the torque applicator are always held in the proper rel

33、ationship during the test. 4.2 Specimen holder The specimen holder shall be a floating fixture to which the device under test is mounted. The holder shall be prohibited from rotating, but shall otherwise be capable of moving freely in order to obtain the proper alignment between the coupling nut or

34、cap and the adapter or other device under test. 6 61300-2-15 IEC:2008(E) Specimen holder Torque gauge and applicator Alignment mechanism Coupling shaft Stand Coupling Device under test IEC 090/08 Figure 1 Coupling torque tester 4.3 Coupling Use a coupling designed to mate with the cap or coupling nu

35、t of the specimen in a such a manner that the torque is applied orthogonally to the coupling interface without the presence of any bending moment. 4.4 Coupling shaft A coupling shaft shall be used to connect the torque applicator through the coupling to the device under test. 4.5 Alignment mechanism

36、 Use an alignment mechanism to ensure that the coupling shaft is always in the proper position relative to the specimen. A clearance hole or low friction sleeve bearing will usually be satisfactory. 4.6 Torque applicator and gauge Torque shall be applied using a torque wrench or equivalent and a tor

37、que gauge, having a torque range of no more than three times the required torque test value. A maximum reading torque indicator is preferred, but not required. The gauge shall be accurate to within 10 % of the applied torque value. 61300-2-15 IEC:2008(E) 7 5 Procedure 5.1 Preparation of specimens Ma

38、te the device to be tested according to the manufacturers instructions. For screw type couplings, use a torque wrench to ensure that the couplings are tightened to the proper value. 5.2 Pre-conditioning Pre-condition the prepared specimens for 2 h at the standard test conditions specified in IEC 613

39、00-1 before beginning the test, unless otherwise specified in the relevant specification. 5.3 Specimen mounting Securely mount each specimen under test, usually the connector adapter, switch, attenuator, etc., to the stationary portion of the test fixture. Connect the torque applicator to the plug c

40、ap or coupling nut through the coupling, coupling shaft and alignment mechanism. 5.4 Torque loading Using the torque applicator, smoothly apply the specified torque to the cap or coupling nut at a nominal rate such that there is no element of impact loading. Unless otherwise specified in the relevan

41、t specification, maintain the specified torque for a minimum period of 15 s. 5.5 Post-test examination Remove the torque load and remove the specimen from the mounting. Unless otherwise specified, examine the specimen and its component parts in accordance with the requirements of IEC 61300-3-1. Chec

42、k for any evidence of cracking, bending or permanent deformation. Check for other damage which might impair its function, and any other pass/fail criteria specified in the relevant specification. 6 Severity The severity of the test is dependant upon the magnitude of the applied torque and to a lesse

43、r extent the duration of the load. The magnitude and duration of the load shall be given in the relevant specification. The following preferred severities are non-mandatory severities which may be applied to this test: Overload torques N m 0,4 0,6 0,8 7 Details to be specified The following details,

44、 as applicable, shall be specified in the relevant specification: magnitude of overload torque; required coupling torque; duration of torque application, if other than 15 s; 8 61300-2-15 IEC:2008(E) pre-conditioning procedure, if different from 5.2; recovery procedure; specimen optical functioning o

45、r not functioning; specimen mated or unmated; initial examinations and measurements and performance requirements; examinations and measurements during test and performance requirements, if required; final examinations and measurements and performance requirements; deviations from the test procedure; additional pass/fail criteria. _ INTERNATIONAL ELECTROTECHNICAL COMMISSION 3, rue de Varemb P.O. Box 131 CH-1211 Geneva 20 Switzerland Tel: + 41 22 919 02 11 Fax: + 41 22 919 03 00 infoiec.ch www.iec.ch