IEC 61300-2-52-2013 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-52 Tests - Bending test for cord.pdf

1、 IEC 61300-2-52 Edition 1.0 2013-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-52: Tests Bending test for cords Dispositifs dinterconnexion et composants passifs fibres optiques Procdures fondame

2、ntales dessais et de mesures Partie 2-52: Essais Essai de courbure pour les cordons IEC61300-2-52:2013 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any for

3、m or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to th

4、is publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lect

5、ronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci

6、-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organ

7、ization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendm

8、ent might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IE

9、C Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical

10、terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publicat

11、ion or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux

12、technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/search

13、pub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform su

14、r les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 t

15、ermes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous

16、 avez des questions contactez-nous: csciec.ch. IEC 61300-2-52 Edition 1.0 2013-02 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 2-52: Tests Bending test for cords Dispositifs dinterconnexion et compos

17、ants passifs fibres optiques Procdures fondamentales dessais et de mesures Partie 2-52: Essais Essai de courbure pour les cordons INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE J ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-83220-652-2 Registered trademark of t

18、he International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61300-2-

19、52 IEC:2013 CONTENTS FOREWORD . 3 1 Scope . 5 2 Normative references 5 3 General description . 5 4 Apparatus . 5 4.1 General . 5 4.2 Cord 5 4.3 Specimen 6 4.4 Optical measurements . 6 5 Procedure . 6 5.1 General . 6 5.2 Preconditioning 6 5.3 Initial examinations and measurements 6 5.4 Procedure 6 5.

20、5 Final examinations and measurements 7 6 Severity 7 7 Details to be specified . 8 Bibliography 9 Figure 1 Specimen fixed onto mandrel 7 Figure 2 Cable wrapped around mandrel 7 Figure 3 Required number of mandrel rotations applied 7 Table 1 Severity . 8 61300-2-52 IEC:2013 3 INTERNATIONAL ELECTROTEC

21、HNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 2-52: Tests Bending test for cords FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electro

22、technical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specificat

23、ions, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International

24、, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal deci

25、sions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for inter

26、national use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In or

27、der to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be cl

28、early indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification

29、 bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, pro

30、perty damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in

31、 this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying an

32、y or all such patent rights. International Standard IEC 61300-2-52 has been prepared by sub-committee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. The text of this standard is based on the following documents: FDIS Report on voting 86B

33、/3547/FDIS 86B/3590/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 61300-2-52 IEC:2013 A list of all the parts in the IEC 61

34、300 series, published under the general title, Fibre optic interconnecting devices and passive components Basic test and measurement procedures can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on

35、 the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61300-2-52 IEC:2013 5 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND ME

36、ASUREMENT PROCEDURES Part 2-52: Tests Bending test for cords 1 Scope This part of the IEC 61300 series describes a procedure to determine the suitability of a cord to withstand bending around a mandrel of the sort to be applied during normal use. This test is only applied to single fibre cables and

37、multiple fibre circular cables. It is not applicable to ribbon cables. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated referen

38、ces, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 1: General and guidance IEC 61300-3-1, Fibre optic interconnecting devices and passive components

39、Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61300-3-3, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-3: Examinations and measurements Active monitoring of changes in attenuation and ret

40、urn loss IEC 61300-3-4, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-4: Examinations and measurements Attenuation 3 General description The purpose of this test is to determine the capability of the cord when repeatedly bent. Optical measure

41、ments are made before and after the test to screen for evidence of damage to the fibre/cable. 4 Apparatus 4.1 General A single mandrel apparatus shall enable the sample to be wrapped tangentially in a close helix around a single test mandrel. 4.2 Cord A cord is a fibre optic cable terminated with an

42、y passive fibre optic connector on both ends, regardless of its expected use. Examples include equipment cords, work area cords or patchcords. 6 61300-2-52 IEC:2013 4.3 Specimen The specimen shall be a cord. The connectors shall be terminated according to the manufacturers instructions so that the f

43、ibre, cable and resilient members are fixed together. 4.4 Optical measurements Unless otherwise specified, measuring equipment specified in IEC 61300-3-4 shall be connected to the specimen for monitoring optical performance during the test. 5 Procedure 5.1 General Sufficient tension shall be applied

44、 to ensure that the sample contours the mandrel. The sample shall then be unwrapped. A cycle consists of one wrapping and one unwrapping. The diameter of the test mandrel, the number of turns of the mandrel and the number of cycles shall be shown in the relevant specification. 5.2 Preconditioning Pr

45、econdition the specimen and all equipment for 2 h under standard test conditions as defined in IEC 61300-1, unless otherwise specified in the relevant specification. 5.3 Initial examinations and measurements Complete the initial examinations and measurements. 5.4 Procedure a) Connect the specimen to

46、 the optical measurement equipment according to IEC 61300-3-3. b) The specimen shall be initially positioned as shown in Figure 1. The two straight sections shall be perpendicular to the mandrel and spacing between the two straight sections shall be such that the diameter of the loop is greater than

47、 the cables minimum bend diameter. c) Start the optical power measurements. d) The specimen shall be wrapped around the mandrel at a uniform tension such that there are no gaps between the cable and the mandrel during the bending cycles (see Figure 2). The required number of turns around the mandrel

48、 shall be applied. Each revolution of cable on the mandrel shall be close to the adjacent revolutions or cable wraps (see Figure 3). e) The specimen shall be kept in this position for at least 1 min. f) The specimen shall be unwrapped and kept in this position for at least 1 min. g) The required num

49、ber of cycles shall be applied by repeating steps d) to f) in a timely manner at a rate no greater than 1 wrap per minute. h) Stop optical power measurements. 61300-2-52 IEC:2013 7 Specimen Mandrel IEC 482/13 Figure 1 Specimen fixed onto mandrel IEC 483/13 Figure 2 Cable wrapped around mandrel IEC 484/13 Figure 3 Required number of mandrel rotations applied 5.5 Final examinat