IEC 61300-3-29-2014 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-29 Examinations and measurements.pdf

1、 IEC 61300-3-29 Edition 2.0 2014-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-29: Examinations and measurements Spectral transfer characteristics of DWDM devices Dispositifs dinterconnexion et c

2、omposants passifs fibres optiques Procdures fondamentales dessais et de mesures Partie 3-29: Examens et mesures Caractristiques de transfert spectral des dispositifs DWDM IEC 61300-3-29:2014-03(en-fr) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerland All r

3、ights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the req

4、uester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune parti

5、e de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de

6、lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland

7、www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under

8、constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical

9、 Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives infor

10、mation on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worl

11、ds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More

12、 than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc

13、If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (IEC) est la premire organisation mondiale qui labore et publie des Normes internationales pour t

14、out ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - we

15、bstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIEC. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.i

16、ec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez in

17、form sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et

18、 dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/glossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extra

19、ites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des

20、questions contactez-nous: csciec.ch. IEC 61300-3-29 Edition 2.0 2014-03 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-29: Examinations and measurements Spectral transfer characteristics of DWDM devi

21、ces Dispositifs dinterconnexion et composants passifs fibres optiques Procdures fondamentales dessais et de mesures Partie 3-29: Examens et mesures Caractristiques de transfert spectral des dispositifs DWDM INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE W ICS 33

22、.180.20 PRICE CODE CODE PRIX ISBN 978-2-8322-1479-4 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assur

23、er que vous avez obtenu cette publication via un distributeur agr. colour inside 2 IEC 61300-3-29:2014 IEC 2014 CONTENTS FOREWORD . 5 1 Scope 7 2 Normative references 7 3 Terms, definitions, abbreviations and symbols . 7 3.1 Terms and definitions . 7 3.2 Symbols and abbreviations 8 3.2.1 Symbols . 8

24、 3.2.2 Abbreviations 8 4 General description . 9 5 Apparatus 10 5.1 Measurement set-up 10 5.2 Light source, S . 12 5.2.1 Tuneable narrowband light source (TNLS) Method A . 12 5.2.2 Broadband source (BBS) Method B . 12 5.3 Tracking filter (TF) . 12 5.4 Reference branching device (RBD) 12 5.5 Waveleng

25、th meter (WM) 13 5.6 Polarizer (PL). 13 5.7 Polarization controller (PC) 13 5.8 Device under test (DUT) 13 5.8.1 General 13 5.8.2 Device input/output optics . 14 5.9 Detector (D) . 14 5.9.1 Broadband detectors, BBD1, BBD2, Method A.1 . 14 5.9.2 Tuneable narrowband detector (TND) Method A.2 and Metho

26、d B 14 5.10 Temporary joints (TJ) . 15 6 Procedure 15 6.1 General 15 6.2 Preparation of DUTs 15 6.3 System initialization . 15 6.4 System reference measurement . 16 6.4.1 General 16 6.4.2 Measurement of the reference spectra for Method A . 16 6.4.3 Measurement of reference spectra for Method B . 16

27、6.5 Measurement of device spectra . 16 7 Characterization of the device under test . 17 7.1 Determination of transfer functions 17 7.1.1 General 17 7.1.2 Accounting for the source variations . 17 7.1.3 Calculations for the Mueller matrix method . 17 7.2 Transmission (T() spectra measurements . 18 7.

28、2.1 General 18 7.2.2 Peak power calculation . 19 IEC 61300-3-29:2014 IEC 2014 3 7.2.3 Normalization of the transfer function . 20 7.3 Calculation of optical attenuation (A) 20 7.4 Insertion loss (IL) . 20 7.5 Bandwidth and full spectral width . 21 7.5.1 General 21 7.5.2 Centre wavelength 21 7.5.3 Ce

29、ntre wavelength deviation . 22 7.5.4 X dB bandwidth 22 7.6 Passband ripple . 22 7.7 Isolation (I) and crosstalk (XT) . 23 7.7.1 General 23 7.7.2 Channel isolation 24 7.7.3 Channel crosstalk . 24 7.7.4 Adjacent channel isolation 24 7.7.5 Adjacent channel crosstalk . 25 7.7.6 Minimum adjacent channel

30、isolation . 25 7.7.7 Maximum adjacent channel crosstalk 25 7.7.8 Non-adjacent channel isolation . 25 7.7.9 Non-adjacent channel crosstalk 26 7.7.10 Minimum non-adjacent channel isolation . 26 7.7.11 Maximum non-adjacent channel crosstalk . 26 7.7.12 Total channel isolation 26 7.7.13 Total channel cr

31、osstalk . 26 7.7.14 Minimum total channel isolation 26 7.7.15 Maximum total channel crosstalk 26 7.8 Polarization dependent loss (PDL() . 27 7.9 Polarization dependent centre wavelength (PDCW) . 27 7.10 Channel non-uniformity 28 7.11 Out-of-band attenuation . 28 8 Details to be specified . 28 8.1 Li

32、ght source (S) . 28 8.1.1 Tuneable narrowband light source (TNLS) 28 8.1.2 Broadband source (BBS) (unpolarized) . 28 8.2 Polarization controller (PC) 29 8.3 Polarizer (PL). 29 8.4 Tracking filter (TF) . 29 8.5 Reference branching device (RBD) 29 8.6 Temporary joint (TJ) 29 8.7 Wavelength meter (WM)

33、29 8.8 Detector (D) . 29 8.8.1 Broadband detector (BBD) 29 8.8.2 Tuneable narrowband detector (TNBD) . 29 8.9 DUT . 30 Annex A (informative) Reflection spectrum measurements . 31 A.1 General 31 A.2 Apparatus 31 A.2.1 General 31 A.2.2 Reference branching device . 31 4 IEC 61300-3-29:2014 IEC 2014 A.2

34、.3 Optical termination . 32 A.3 Measurement procedure 32 A.3.1 General 32 A.3.2 Determination of source reference spectrum . 32 A.3.3 Determination of system constant . 32 A.3.4 Determination of reference reflectance spectrum 33 A.3.5 Determination of device reflectance spectrum . 33 A.3.6 Determina

35、tion of optical attenuation 33 A.4 Reflection R() spectra measurements 34 Annex B (informative) Determination of the wavelength increment parameter 35 Annex C (informative) Determination of a mean value using the shorth function . 37 Bibliography 39 Figure 1 Basic measurement set-up . 10 Figure 2 Me

36、asurement set-up for tuneable narrowband light source (TNLS) system . 11 Figure 3 Measurement set-up for TNLS and tuneable narrowband detector (TND) system 11 Figure 4 Measurement set-up for BBS and tuneable narrowband detector (TND) system 11 Figure 5 System reference for transmission measurement .

37、 16 Figure 6 Normalized transfer functions . 19 Figure 7 BW and full spectral width for a fibre Bragg grating 21 Figure 8 X dB bandwidth 22 Figure 9 Passband ripple . 23 Figure 10 Channel isolation and crosstalk 24 Figure 11 Minimum adjacent channel isolation . 25 Figure 12 Polarization dependence o

38、f the transfer function 27 Figure 13 Polarization dependent centre wavelength (PDCW) 28 Figure A.1 Measurement set-up for a single port device . 31 Figure A.2 Source reference set-up . 32 Figure A.3 Set-up for measurement of system constant . 33 Figure C.1 Example response and x dB wavelengths . 37

39、Figure C.2 Example showing the 0,5 dB wavelengths based on the shorth (dotted vertical lines) and the mean (solid vertical lines) . 38 Table 1 Test methods 10 IEC 61300-3-29:2014 IEC 2014 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC T

40、EST AND MEASUREMENT PROCEDURES Part 3-29: Examinations and measurements Spectral transfer characteristics of DWDM devices FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National

41、Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly A

42、vailable Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmenta

43、l organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on tech

44、nical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by I

45、EC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international unifo

46、rmity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5)

47、IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensur

48、e that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of an

49、y nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publica